Will there be an update for your scopes that don’t have an internal rangefinder? I have a couple of the Thermion 2 XP 50’s, which don’t have built-in internal rangefinders because I wanted to do field sweeps with a monocular instead of a rifle barrel. To that end, I also have 2 Axion 2 LRF XG 35’s, so no need for a LRF within the scope. Any ballistics support coming eventually for those of us that have your Axion monoculars to scan and determine range? It would be just a simple mathematical table that could be transferred from the Stream app to the riflescope, and the shooter uses the dial to select the distance. Please support your long time customers too that don’t have an LRF scope, but do have the same capabilities using your monoculars.
@@PulsarVision I have two Thermion 2 XP 50 scopes, which are not the Pro model. Are my models upgradeable to this firmware? If no, why wouldn’t they be capable of doing the exact same thing?
Got mine to pair. Sequence - 1. scope off, phone off, turn scope on, set bluetooth on scope to on. start phone insure blue tooth is on. set pairing on scope, open app on phone, follow screen directions, pairing should occur and you should get a 4 digit code on your scope, enter the 4 digits into the app. You should be ready to go. However, I found many more bugs in the app!
Hi! Please follow these steps: 1. connect your non-LRF riflescope to the Stream Vision Ballistics mobile application 2. create up to ten ballistic profiles and upload them to the scope. 3. After uploading the profiles, disconnect from the app, go to the long menu of the device and select one of the profiles. 4. Then switch to the short menu and manually input the preferred distance to the target. 5. Now the ballistic calculations will be made inside the riflescope and the suggested point of aim will be displayed on your scope’s screen.
Really looking forward to being able to upgrade my Thermion 2 LRF XG50, When I read this in the IWA news, it made me go with Pulsar. Can you please give me some idea of when it will be released? thanks
I purchased my XP50 pro LRF about 2 years ago. I like it. This new firmware and app seem like a great idea. BUT it does not work. I installed both the firmware and the app. Continuously get a "red flashing screen" in the scope when I try to use the new LRF BC parameter. I talked to Pulsar and sent my unit back under warranty for a fix. After 4 weeks of no communication I called. After another 10 days or so Pulsar decided to send me a new XP50 pro LRF. Well I have the same problem. The app also has bugs all over the place and changes my parameters to metric when saving the profiles. I am an old guy but was a software developer and programmer during my early career. In my humble opinion this version of the product is not yet ready for release.
I think this is really neat idea, but I have some suggestions on the implementation. First, why not build this into the current Stream Vision app? Let me store all of these attributes for each cartridge AND rifle as a 'zero' or 'sight-in.' I'm sure that the app can generate and store holdover/under in a table from 0 to X yards, and then once the distance is ranged the right figure is read from the table and a new line added to the vertical cross hair. That's how it works, right? Updating the Stream Vision app instead of having a separate app means I can connect to my Trail 2 LRF that doesn't support Bluetooth, just WiFi. But this functionality could readily be added to a variety of scopes. Guys, I like my Trail 2 LRF's form factor over that of the Thermion 2 LRF... it's easier for me to mount to a variety of firearms with Picatinny rails. Please, get the update out for the Trail 2 LRF... thanks!
Hello! Thank you for your feedback and suggestions for improving Stream Vision 2 app. We are working on an update for Trail 2 LRF that will allow you to use the ballistic calculator. As soon as the release is ready, we will announce it in our official channels.
Thanks for your feedback. please specify at what stage the connection fails? Please contact us directly: support@pulsar-vision.com we need more details of this issue
Hello! A new firmware for Thermion 2 LRF XQ Pro / Thermion 2 LRF XG50 is now on the priority list for release, it will be released soon. we will prepare a release for Trail 2 LRF later.
I hope there's options for different aiming indicators, that cross obscures way too much of the target. Hopefully won't much longer and the ballistics app will be downloadable in Australia, damn keen to try this out.
@55gnvmax damn, really gotta wonder what they were thinking when they designed that. Might work fine for shooting massive steel gongs but totally useless for pest control. The app still isn't downloadable for us Aussies yet either 🤦♂️
@@55gnvmax Hi! There is an option to change reticle types: www.pulsar-nv.com/glo/support/manuals/2966/thermion-2-lrf-xp50-pro-reticle-type/s1557/ and here you will find info how to change the LRF reticle: www.pulsar-nv.com/glo/support/manuals/2966/thermion-2-lrf-xp50-pro-rangefinder/s1565/
@@stuartgillahan Hi! How to change reticle type of the riflescope: www.pulsar-nv.com/glo/support/manuals/2966/thermion-2-lrf-xp50-pro-reticle-type/s1557/ and here you will find info how to change the LRF reticle: www.pulsar-nv.com/glo/support/manuals/2966/thermion-2-lrf-xp50-pro-rangefinder/s1565/ or do you mean something else?
@@PulsarVision the coment was not about the reticle type, its about an option to change the type of sugested aiming point (the X) as could obstruct a small target as it is quite thick as its overlaid on the reticle. would it not be better for the whole reticle to move to the sugested aiming point
@@PulsarVision thanks for answering my question.iy will glad to wait update to use calculator od c50.can you say approximately when will be update available?thanks upfront!!!!best regards Tomislav!
Hi! We released a new FW update for the Digex C50 yesterday. Please download the update to your device. If you have any questions, please contact us directly: support@pulsar-vision.com
@@PulsarVision Greetings. Thank you very much for the upgrade. Yesterday I downloaded it and upgraded the c50. Today we will play a little and see how the ballistic calculator works. I tried the zoom last night and it works much smoother. Thank you once again and if I have any questions and suggestions I will write to you. Greetings Tomislav
Bugs in the program! Told me to hold under at over 400 yds. My zero is 124 yds. Had to restart the scope to get it to work again. Then it did it again. Now knockked it off its a waste of time. Dont get to excited folks. Lots of people must be having issues with this, as there are no videos on RUclips or other social media, even from retailers to promote the product (weird)
I'm shocked that a rifle scope manufacturing company does not understand hold under. The suggested aiming point was above the horizontal line of the cross hair, therefore suggests I hold under @ 400yds. My current zero is 124 yards, so should be hold over. Suggest aiming point should be below the horizontal line. I shut down my scope and restarted it which fixed the issue temporarily until it happened again.
Could you please send us screenshots from the application with the settings in the profile, as well as the coordinates on which the distance is reset to zero ( screenshots from the riflescope) support@pulsar-vision.com
This ballistic app was a MAJOR deciding factor for me choosing pulsar.
Thanks Pulsar for leading the market in the right direction!!
Hello! Thanks for your support! It is very important for us! we will continue to offer the most interesting and progressive solutions in this field.
I have the thermion XL50 on order and I can’t wait to get it and start testing it out
Will there be an update for your scopes that don’t have an internal rangefinder?
I have a couple of the Thermion 2 XP 50’s, which don’t have built-in internal rangefinders because I wanted to do field sweeps with a monocular instead of a rifle barrel. To that end, I also have 2 Axion 2 LRF XG 35’s, so no need for a LRF within the scope. Any ballistics support coming eventually for those of us that have your Axion monoculars to scan and determine range?
It would be just a simple mathematical table that could be transferred from the Stream app to the riflescope, and the shooter uses the dial to select the distance.
Please support your long time customers too that don’t have an LRF scope, but do have the same capabilities using your monoculars.
Hi! We have released an update for Thermion 2 XP50 Pro (without LRF) series. please specify the model of your scope.
@@PulsarVision I have two Thermion 2 XP 50 scopes, which are not the Pro model. Are my models upgradeable to this firmware? If no, why wouldn’t they be capable of doing the exact same thing?
Bluetooth does not pair with android. I have tried with a borrowed iPhone and it worked. When will the android issue be resolved?
Hi! Our developer is working on the issue, they will release a fix very soon
Got mine to pair. Sequence - 1. scope off, phone off, turn scope on, set bluetooth on scope to on. start phone insure blue tooth is on. set pairing on scope, open app on phone, follow screen directions, pairing should occur and you should get a 4 digit code on your scope, enter the 4 digits into the app. You should be ready to go. However, I found many more bugs in the app!
So my question is how can I use this with my XQ50 PRO without the range finder on the scope
Hi! Please follow these steps:
1. connect your non-LRF riflescope to the Stream Vision Ballistics mobile application
2. create up to ten ballistic profiles and upload them to the scope.
3. After uploading the profiles, disconnect from the app, go to the long menu of the device and select one of the profiles.
4. Then switch to the short menu and manually input the preferred distance to the target.
5. Now the ballistic calculations will be made inside the riflescope and the suggested point of aim will be displayed on your scope’s screen.
Really looking forward to being able to upgrade my Thermion 2 LRF XG50, When I read this in the IWA news, it made me go with Pulsar. Can you please give me some idea of when it will be released?
thanks
Hi! The update is in its final stages. we hope to release it as soon as possible.
Same here, all the XG folks are VERY eager for this roll out
I purchased my XP50 pro LRF about 2 years ago. I like it. This new firmware and app seem like a great idea. BUT it does not work. I installed both the firmware and the app. Continuously get a "red flashing screen" in the scope when I try to use the new LRF BC parameter. I talked to Pulsar and sent my unit back under warranty for a fix. After 4 weeks of no communication I called. After another 10 days or so Pulsar decided to send me a new XP50 pro LRF. Well I have the same problem. The app also has bugs all over the place and changes my parameters to metric when saving the profiles. I am an old guy but was a software developer and programmer during my early career. In my humble opinion this version of the product is not yet ready for release.
Hello! Thank you for providing extensive feedback about the app. We have passed the information to the software developer for investigation.
Please tell me there is an option to change the marker to a straight horizontal line from a cross.
Exelent! Line should be with hashmarks for 2, 4, 6 etc... meters/sec at that distance for your shooting profile.
@@user-kq9wb7uk5x Hello! could you send us a clarification of your proposal - what should the aiming indicator look like support@pulsar-vision.com
I think this is really neat idea, but I have some suggestions on the implementation. First, why not build this into the current Stream Vision app? Let me store all of these attributes for each cartridge AND rifle as a 'zero' or 'sight-in.' I'm sure that the app can generate and store holdover/under in a table from 0 to X yards, and then once the distance is ranged the right figure is read from the table and a new line added to the vertical cross hair. That's how it works, right?
Updating the Stream Vision app instead of having a separate app means I can connect to my Trail 2 LRF that doesn't support Bluetooth, just WiFi. But this functionality could readily be added to a variety of scopes. Guys, I like my Trail 2 LRF's form factor over that of the Thermion 2 LRF... it's easier for me to mount to a variety of firearms with Picatinny rails.
Please, get the update out for the Trail 2 LRF... thanks!
Hello! Thank you for your feedback and suggestions for improving Stream Vision 2 app.
We are working on an update for Trail 2 LRF that will allow you to use the ballistic calculator.
As soon as the release is ready, we will announce it in our official channels.
@@PulsarVision Do you have any updates on when the Trail 2 LRF firmware update will be available?
What mounts are you using and height of mount?
Looking forward to try this one out !🎉
Hi! have you tried a new SV Ballistics app?
Is there a way to get rid of the adjusted hold over (red X) and return to an uncluttered crosshair and normal zero?
Hi! sure, just turn off Ballistic calculator in your device (www.pulsar-nv.com/glo/support/manuals/2966/thermion-2-lrf-xp50-pro-rangefinder/s1565/)
Why it’s not possible to download from German store. I’m hunting a lot in other Austria and I can’t use the app…
Hello! Thermal and digital sights are prohibited in Germany, so the app is not available.
I have the latest download supposedly fixing android connection issues and mine still won't connect
Thanks for your feedback. please specify at what stage the connection fails? Please contact us directly: support@pulsar-vision.com
we need more details of this issue
It is great news! But why point of aim is SO big? If we are tallking about sharp shooting - the point of aim must be very small and thin.
Hi! Thank you for your opinion. It is very important for us to receive feedback from users. it allows us to make our products better
Is the trail 2 update still coming? it been 2 months...
Hello! A new firmware for Thermion 2 LRF XQ Pro / Thermion 2 LRF XG50 is now on the priority list for release, it will be released soon.
we will prepare a release for Trail 2 LRF later.
Hello just checking in to see if the Trail 2 update is any closer? @@PulsarVision
Bluetooth doesn't pair with Android. When is this going to be fixed?
Hi! We are sorry that you have to wait, we are working on a solution.
@@PulsarVision Thank you.
For thermion XQ50 LRF When will it be available?
Hi! a new FW for thr Thermion 2 LRF XQ Pro is under development now, it will be released soon.
I hope there's options for different aiming indicators, that cross obscures way too much of the target. Hopefully won't much longer and the ballistics app will be downloadable in Australia, damn keen to try this out.
I have this on my scope and there is no option that i can see to change the aiming indicator.
@55gnvmax damn, really gotta wonder what they were thinking when they designed that. Might work fine for shooting massive steel gongs but totally useless for pest control. The app still isn't downloadable for us Aussies yet either 🤦♂️
@@55gnvmax Hi! There is an option to change reticle types: www.pulsar-nv.com/glo/support/manuals/2966/thermion-2-lrf-xp50-pro-reticle-type/s1557/
and here you will find info how to change the LRF reticle: www.pulsar-nv.com/glo/support/manuals/2966/thermion-2-lrf-xp50-pro-rangefinder/s1565/
@@stuartgillahan Hi! How to change reticle type of the riflescope: www.pulsar-nv.com/glo/support/manuals/2966/thermion-2-lrf-xp50-pro-reticle-type/s1557/
and here you will find info how to change the LRF reticle: www.pulsar-nv.com/glo/support/manuals/2966/thermion-2-lrf-xp50-pro-rangefinder/s1565/
or do you mean something else?
@@PulsarVision the coment was not about the reticle type, its about an option to change the type of sugested aiming point (the X) as could obstruct a small target as it is quite thick as its overlaid on the reticle.
would it not be better for the whole reticle to move to the sugested aiming point
How to connect to Digex C 50?
Iy want to know too how to connect and use calculator on digex c50
Hello! The Digex C50 cannot yet use the ballistics calculator, but we will soon offer a FW update that will allow to use it.
@@PulsarVision thanks for answering my question.iy will glad to wait update to use calculator od c50.can you say approximately when will be update available?thanks upfront!!!!best regards Tomislav!
Hi! We released a new FW update for the Digex C50 yesterday. Please download the update to your device. If you have any questions, please contact us directly: support@pulsar-vision.com
@@PulsarVision Greetings. Thank you very much for the upgrade. Yesterday I downloaded it and upgraded the c50. Today we will play a little and see how the ballistic calculator works. I tried the zoom last night and it works much smoother. Thank you once again and if I have any questions and suggestions I will write to you. Greetings Tomislav
Trail 2 xp50 lrf in the list ??
Yes it's supposed to follow shortly. I'm pretty sure it was a official pulsar news release not 3rd party that said it. I'm trying to find it.
@@04firebolt that'll be epic
Is the app going to work with my trail 2 in the future???
Hi! we are going to add the Trail 2 LRF to the list of compatible devices compatible with the SV Ballistics app, but later
Bugs in the program! Told me to hold under at over 400 yds. My zero is 124 yds. Had to restart the scope to get it to work again. Then it did it again. Now knockked it off its a waste of time. Dont get to excited folks. Lots of people must be having issues with this, as there are no videos on RUclips or other social media, even from retailers to promote the product (weird)
Hi! thank you for your feedback. we need more details to understand and to analyze the issue. please contact us directly support@pulsar-vision.com
I'm shocked that a rifle scope manufacturing company does not understand hold under.
The suggested aiming point was above the horizontal line of the cross hair, therefore suggests I hold under @ 400yds. My current zero is 124 yards, so should be hold over. Suggest aiming point should be below the horizontal line.
I shut down my scope and restarted it which fixed the issue temporarily until it happened again.
Could you please send us screenshots from the application with the settings in the profile, as well as the coordinates on which the distance is reset to zero ( screenshots
from the riflescope) support@pulsar-vision.com
I have created a video:
ruclips.net/video/P2RZXDlEWos/видео.html