Sir, can you create a time delay, for example if you have an blackout and power to return, would this device be able to delay for 10 seconds before the current pass through to the loads? Great video👍🏽
I've mistakenly turned on the prepaid and went to the extent of removing the device from the system assuming it's faulty. We don't have a prepaid system in my country. Also was wondering why not a postpaid bill value calculator
I also wished they had an option to disable the power button. If you press the button before you enter the device, you can press it off with a single click (it doesn't ask you like when you enter the device page). Does this also measure cumulative power? I have the power meter variant. It shows me total KW instead of instantaneous power. I wish it would show both, instead of current ;-)
Can we put a limit on the kWh Units Consumed? for example we set a litmit of 150 kWh energy usage. So once we consume 150 kWh, the Switch turns Off automatically
i think power button and prepaid feature on that application is good feature...the main problem is that you don't have any backup/battery power on your internet router/modem so where when you used that feature it will cut power also on your router...so make sure you have power backup on your internet router/modem...CMIIW
Maybe I was not clear enough about what I was complaining. The problem is that you can't override from the unit itself the prepaid feature. If it would have a key combination to restart it, at least for a few minutes to change the prepaid value from the app, you would not need backup or battery power. But, now that I'm thinking about it, battery power is not even enough, you would need something to keep the router going for weeks, to be absolutely sure you don't end up in the same situation I did. So, it would only be ok if the router would be powered before the circuit that this breaks.
I was trying to guess what that cost management function was for. I thank you for the warning, that part really is a poorly thought out design, I was lucky not to activate it with 0.
it is for restrict your electricity usage. Like you wanted to stop using your electricity after 200/100 / etc.. Units. Just stop the option if you don’t want it. Though it is a Very neddy option for many people.
You did not get it. It's close to impossible to reactivate the unit once that triggers. Just watch my video again to undrstand it. The option is really good for who needs it, but an override should exist on the unit itself, not only in software.
Maine ye lagaya hai 2 month sahi chala hai par ab output nai dera Input ari hai, volt b show hore hein lcd pr, wifi b chalra hai Sirf output nai nikal raha Kya solution hai?
Hello. At work I have to connect devices to 220 volts. But the devices may be faulty. My knowledge of electrical engineering is low. Is it possible to connect this protective device to the output of a laboratory transformer and gradually raise the voltage to turn on the computer power supply? Because it is unknown whether the computer power supply circuit is working or not...
Hello. Talk to an electrician about that. But, my guess is that this is not the right device for the job, as for sure it will not like changing in voltage.
Testeaza dar la mine daca deconectez si pica netul,apas comanda de conectare si cand s a conectat la net ,porneste tensiunea,deci are un fel de memorare. Testeaza,al meu e de 63A
Daca ii pica netul nici ca nu isi mai revine.Trebui resetat manual ca la prima pornire.Gresesc eu undeva de se dezactiveaza si nu se mai activeaza automat Desi el inregistreaza nu mai arata in aplicatia Tuya iar cand il resetez din butonul wifi calculeaza consumul de unde a rămas pana la reconectare.Are functie cumva de reconectare automata cand revine net si nu stiu eu sau care este problema ?
@@gabrielchis5664 sincer sa fiu nu stiu daca eu am activat aceasta functie, dar ale mele,ca am doua,cand pica netul si reapare ele se conecteaza automat
@@carlos_sacalulNu am gasit nimic de conectat in setări insa la mine problema este săptămânală.Asta a fost banuiala mea ca daca ii pica net-ul nu se mai reconecteaza.Oare sa fie altceva ? In rplicatie imi apare contor electric (așa l-am numit )dezactivat.Intru in aplicație si imi cere activarea bloothoot si reinregistrare dispozitiv.Pasi ce ii fac la fiecare conectare.El inregistreaza consumul in dispozitiv iar in Tuia nimic.La reconectare imi afiseaza in aplicatie tot consumul de la dezactivare până la reactivare .
Si la mine se reconecteaza automat. Dar...am avut un router la care unele device-uri nu se reconectau cum trebuie singure. Deci e posibil sa fie si ceva de genul.
Thanks for your quick reponse! One more question if you let me: if you do not need to connect remotely to the breaker, and only need to connect to it at home, does it connect to your phone thru "wi-fi direct"?
You can reset by using remove device and wipe data feature but the only thing that wont reset would be Total KWH reading - However you can set a new KWH reading on the device by pressing power button and stopping at 0.0 KWH
@@UltimateDIY yeah it is, only issue it doesnt have the terminals wide enough for a mk unit. but managed to get higher gauge wiring to make it all connect
Maybe you made the same mistake as I made and you activared prepay mode without setting a value bigger than 0. Or maybe you set aome other protection at a level that gets directly triggered.
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
THANK YOU FOR WATCHING!
PLEASE LIKE AND SUBSCRIBE!
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
Sir, can you create a time delay, for example if you have an blackout and power to return, would this device be able to delay for 10 seconds before the current pass through to the loads? Great video👍🏽
Yes. That is exactly like I have it configured. I avoid flickering.
Thank you very much. a very nice video from a fellow RO guy. Maybe an UPS to the Router will resolve the no power issue with the router :).
Thank you! Yes, that would be the fix 👍🏻
Hello, can you create automations based on the readings given by the meter? For example if the instant consumption is >500w turn off a relay
Hello. Yes, it can do that.
11:00 thanks for the warning
Welcome!
I've mistakenly turned on the prepaid and went to the extent of removing the device from the system assuming it's faulty. We don't have a prepaid system in my country. Also was wondering why not a postpaid bill value calculator
If they would want, most likely they can code the software for that.
I also wished they had an option to disable the power button. If you press the button before you enter the device, you can press it off with a single click (it doesn't ask you like when you enter the device page).
Does this also measure cumulative power? I have the power meter variant. It shows me total KW instead of instantaneous power. I wish it would show both, instead of current ;-)
I don't have a power button anywhere alse, only in the app.
Mine measures instant power and shows it as Active Power in kW.
How to change total forward energy Reading?
No idea
Thx for this Video, its perfect for my Hobbyroom.
Welcome!
Can we switch the mcb on/off from the app? If we have the wifi always available
Yes.
Can we put a limit on the kWh Units Consumed? for example we set a litmit of 150 kWh energy usage. So once we consume 150 kWh, the Switch turns Off automatically
Yes, it can be done. I did this by mistake 🤭
So this acts as a breaker as well or should add another breaker after this?
It also acts like a breaker, but an electronically controlled one. I would also add a standard breaker.
i think power button and prepaid feature on that application is good feature...the main problem is that you don't have any backup/battery power on your internet router/modem so where when you used that feature it will cut power also on your router...so make sure you have power backup on your internet router/modem...CMIIW
Maybe I was not clear enough about what I was complaining. The problem is that you can't override from the unit itself the prepaid feature. If it would have a key combination to restart it, at least for a few minutes to change the prepaid value from the app, you would not need backup or battery power. But, now that I'm thinking about it, battery power is not even enough, you would need something to keep the router going for weeks, to be absolutely sure you don't end up in the same situation I did. So, it would only be ok if the router would be powered before the circuit that this breaks.
Wi-Fi modern take power from this breaker in coming
over voltage sensing time VHEE is 1 or can also be down to 0.1sec?@@UltimateDIY
I was trying to guess what that cost management function was for. I thank you for the warning, that part really is a poorly thought out design, I was lucky not to activate it with 0.
Welcome 👍🏻
I had the same issue thing with the expense prepaid, needed to disconnect it again and try it out inside my home
Yup, that is a big and ugly trap
it is for restrict your electricity usage. Like you wanted to stop using your electricity after 200/100 / etc.. Units. Just stop the option if you don’t want it. Though it is a Very neddy option for many people.
You did not get it. It's close to impossible to reactivate the unit once that triggers. Just watch my video again to undrstand it. The option is really good for who needs it, but an override should exist on the unit itself, not only in software.
Hello. Can we control Heaters like dimmer?
Not really sure what you want to do.
Maine ye lagaya hai 2 month sahi chala hai par ab output nai dera
Input ari hai, volt b show hore hein lcd pr, wifi b chalra hai
Sirf output nai nikal raha
Kya solution hai?
Really hard to guess without seing myself. It seems to be off somehow.
@@UltimateDIY sahi, sab kuch sahi chal raha hai siwaye output k, mujhe lga kahein ksi setting ka masla na ho…. Ksi technician ko dikhata hun
@@AhsanZafar try that, but could also be from settings. Maybe you activated the cost/consumption limit in the app by mistake.
@@UltimateDIY i have tried after turning it off, I also have added a balance of 1000 units but still no output
No other idea then...
I wish you showed how you installed it
I never show electrical work, as people might get hurt trying to replicate it. Get an electrician to do it.
@UltimateDIY ah ok gotcha.
Hello. At work I have to connect devices to 220 volts. But the devices may be faulty. My knowledge of electrical engineering is low. Is it possible to connect this protective device to the output of a laboratory transformer and gradually raise the voltage to turn on the computer power supply? Because it is unknown whether the computer power supply circuit is working or not...
Hello. Talk to an electrician about that. But, my guess is that this is not the right device for the job, as for sure it will not like changing in voltage.
Testeaza dar la mine daca deconectez si pica netul,apas comanda de conectare si cand s a conectat la net ,porneste tensiunea,deci are un fel de memorare. Testeaza,al meu e de 63A
Pai e normal. Problema e daca routerul e deconectat prin siguranta asta, atunci nu are de unde sa mai primeasca net 🤭
Daca ii pica netul nici ca nu isi mai revine.Trebui resetat manual ca la prima pornire.Gresesc eu undeva de se dezactiveaza si nu se mai activeaza automat Desi el inregistreaza nu mai arata in aplicatia Tuya iar cand il resetez din butonul wifi calculeaza consumul de unde a rămas pana la reconectare.Are functie cumva de reconectare automata cand revine net si nu stiu eu sau care este problema ?
@@gabrielchis5664 sincer sa fiu nu stiu daca eu am activat aceasta functie, dar ale mele,ca am doua,cand pica netul si reapare ele se conecteaza automat
@@carlos_sacalulNu am gasit nimic de conectat in setări insa la mine problema este săptămânală.Asta a fost banuiala mea ca daca ii pica net-ul nu se mai reconecteaza.Oare sa fie altceva ? In rplicatie imi apare contor electric (așa l-am numit )dezactivat.Intru in aplicație si imi cere activarea bloothoot si reinregistrare dispozitiv.Pasi ce ii fac la fiecare conectare.El inregistreaza consumul in dispozitiv iar in Tuia nimic.La reconectare imi afiseaza in aplicatie tot consumul de la dezactivare până la reactivare .
Si la mine se reconecteaza automat. Dar...am avut un router la care unele device-uri nu se reconectau cum trebuie singure. Deci e posibil sa fie si ceva de genul.
How restart to factory parameters?
Sorry, but that I don't remember. I should be in the manual and I show the manual in the video.
Can we reset the total kwh?
Good question. I don't remember seeing any way to do that.
Hello, sir. Can it only show the total kWt consumed so far, or also the current power in watts being consumed?
It is probably shown in kWt/h.
Hello. It shows instant power also in kW.
Thanks for your quick reponse!
One more question if you let me: if you do not need to connect remotely to the breaker, and only need to connect to it at home, does it connect to your phone thru "wi-fi direct"?
Never tested that, but you can create a hotspot with your phone and connect it trough that for sure.
Thanks alot!
I want to always light one of the displays if possible.
I don't remember that, but in case I show in the video somewhere in the settings a display timeout, maybe it can be set to off.
Is there a way to export the energy data in kwH to Excel?
I don't think so.
@@UltimateDIYNo, and tuya only records hourly data for a week. After that the best you get is daily stats.
Yes, you are right. I thought it's an error, but now you confirmed it.
Tengo 2 líneas para generar 220V, como se conectaría con 2 Líneas más el neutro?
Sorry, but you need to contact someone local to see your setup.
How to reset thos device?
You can reset by using remove device and wipe data feature but the only thing that wont reset would be Total KWH reading - However you can set a new KWH reading on the device by pressing power button and stopping at 0.0 KWH
@@uschhudrophae3078 i want to reset by device... How is it possible
My device app is giving Credit Alarm red alert again and again, any solution?
Maybe you set some limit wrong.
What is A B C on Green card How we Can Use other green cards showing ampere vlot etc
I only have A
Salut. Cum dau un hard reset? Am dat din gresela off la dispaly si acum nu stiu cum să-l mai pornesc. Din aplicație nu imi da posibilitatea asta😂. Ms
Salut. Nu am idee. Ai gasit cumva?
Good job :P
Thanks 👍🏻
My device is not giving output watts even there is no error like leakage, voltage, ampere etc
Device is in on condition, only wifi light is on,
Really hard to guess without seing myself...
I got a 60amp one
From the same "brand"? Is it reliable?
@@UltimateDIY yeah it is, only issue it doesnt have the terminals wide enough for a mk unit. but managed to get higher gauge wiring to make it all connect
But its already a 63amp ,why you said you you got 60amp one @aminkhan1292
@@pannuharkanwal the one I bought was similar to this same brand but lower amp
برآے مھربانی اس پروڈکٹر سے اجتناب کی جائے ہم نے استعمال کیا ہے بہت کمزور ہے اسکی کل 7 دن ذندہ گی ہیں
Mine is still perfectly working.
My controller turns off as soon as it is turned on. Please tell me any remedy
Maybe you made the same mistake as I made and you activared prepay mode without setting a value bigger than 0.
Or maybe you set aome other protection at a level that gets directly triggered.