No ebike that is 48V is able to get to 40 mph. Closest you can get to is 52v ebike with 1000w or 1500w motor will get you to 37-39mph. To get to 40 mph you will need 2000w and 60V and that bike will weight 135 lbs
I Ritch, I have 2 other e bikes that have great pedal assist right from the start where the Ridstar you must pedal a few times before assist kicks in. Even at speed when I let off throttle and pedal the assist will kick in when it wants to. I have bought a new controller and no difference. I found a video that explained all settings and set for max assist but it's just a little better. ??
Some bikes PAS kick is much quicker then other and sensitivity can be adjusted in the settings. I wonder if the cadence sensor on crank has too few magnets and the sensors is limited. Maybe try changing sensor or increasing the setting for the number magnets to fool the controller?
Does the mg01 not use this screen? a Link to the full user manual is below: drive.google.com/file/d/11lAw9iM5LSeClU6BIZ9uhWouXFD8nR_3/view?usp=share_link
Hi B Rich love your videos. I have purchased this bike after watching the unboxing and review video of yours. To be clear p17 cruise is that throttle on and off? ( I live in Australia and it legally cannot be ridden with a throttle in public areas) so I need to disable the throttle. My bike hasn’t arrived yet and like you will raise the stem.
I believe it is p17 to disable the throttle. See this link for full manual drive.google.com/file/d/11lAw9iM5LSeClU6BIZ9uhWouXFD8nR_3/view?usp=share_link
Please help!! I have a new model M5 display on my ridstar it has P0 1 Thur 0 and P1. 1 thru 0. Most of the settings are the same as the old one. P0 8 is speed control. Problem is I was messing around with it and now I have no throttle.
Thanks for this! Can you tell me the best settings for good pedal assist from a dead start and still have max speed throttle? I would like dial it in to have a faster pedal assist.
My pas 5 only has 000 or 1 or 2 and on 000 I get 29 MPH with throttle on 1 or 2 I only get10.5 MPH with the throttle. Is this the normal?? @@BRichSolution
To factory reset the display : P16 - hold mode and down button until the screen flashes. It will reset all settings to default. Mine had P08 032 and would not let us change it to anything else. Had to call the ebike manufacturer and he had us do the above steps which factory reset it. It was then back to max speed of 100 on P08.
Just bought the Ridstar 48v 1000w foldable. But it will not accept any input changes PO1 thru P20. The M5 display shows the changes but the bike reacts exactly the same to manual pedal and throttle inputs. Also, I can turn it on and start the bike up without the battery key inserted or in either of it's two positions?? Any idea's anyone?
Hi I have similar problem on my ridstar but not with every settings. But for example I change P11 or P12 or p14 and bike reacts exactly the same regardless of values in settings. Did you find any solution for that?
@@mrgodzio1750 I finally emailed the manufacturer in Thailand. They sent me a new controller after I complained about the inability to self customize. They initially said it was a safety issue. I threatened to return since I bought it on Amazon. That changed their tone. And sent me an extra battery to keep me happy. 😁👍
How do I do cruise control ? I broke my M5 on my ridstar got a new one and it finally give me cruise ? I saw that if it’s on you can throttle the bike and the hold down button at the same time
Setting Current Limit (P14) to 22Ampere give you more current (if your battery can provide enough) and you get more power, but if the controller isn't designed to support 22A (you have to check on your controller specs)you will break it quickly, specially if you ask that current for long time, so i will suggest to keep it at default value, or just few amp more.
Hi, my display is only @ 16 which is confusing. I did install a turning signal and moved the display around on the handle bar so does that have something to do with it? I want to completely reset this screen back to all factory setting. Please help😅 thanks
I did not see factory reset option in the manual. Use the video to set each option to factory setting. Link to full manual drive.google.com/file/d/11lAw9iM5LSeClU6BIZ9uhWouXFD8nR_3/view?usp=share_link
I have 5 miles on mine and two days later went to ride it and it will not power up. Checked the battery and it is fully charged with 54.4 volts. Any suggestions?
I have the Ridstar H20...just arrived. I went in to the advanced settings as described and changed the distance to km, and screen brightness. I'm a bit concerned that P05 which in the video shows to be set at 01....mine is set to 05. Toggling up and down does not allow me to change that value to 01. So my first question is....what does P05 control and secondly...is the setting of 05 correct or not?
See full user manual p05 is help bit file which i believe allow 0-3 PAS mode or 0-5 PAS. drive.google.com/file/d/11lAw9iM5LSeClU6BIZ9uhWouXFD8nR_3/view?usp=share_link
P5 is number of gears, it’s set at 5 you can make 3 or 9. Not sure why it changes the first number when you hit down compared to cycling through by pressing up. In other words idk the difference between 0.05 and 1.05
hello i have this M5 pannel too, but i cannot go to settings when i press down on arrow buttons. it kinda asks me a code with 3 digits could you help me about this ?
H20 must have different settings then. Put settings back to default and then change each setting individually and test before going to the next setting
I just received my new bike and the controller switch is a different style than the one you have to adjust the screen settings. Mine has a + and a - button with out an M to make changes. Also my manual has the older style switch noted. I can get into the screen menu buy cant make any changes. Any suggestions? Thank you
Hi, i have an ouxi V8 with the M5 display, but i cant change all of the settings, only the brightness, speed limit and PAS mode. Any suggestions for a display that will let me change all of the settings? also, the bike only goes 40/42 km/h on GPS, yet the display says 50.. should i just buy a better controller so it goes faster?
Witam. Jest taki problem ,lub niema ? Jak cofam rowerem do tyłu to nie idzie płynnie jak na luzie tylko z lekkim oporem ? Klocki nie trzymają ? Może być problem z silnikiem ?
Hi I was watching your video about ridstar adjusting the lcd I tried to follow all your numbers but my bike stop running no more I don’t know if I press something wrong & that’s the reason my bike stop running pls if you guide me how to run my bike back I had the 1000w 48v15ah ridstar I just finished assembling the bike & I start adjusting control panel LCD while watching you & unfortunately my bike stop running & I didn’t put any mile on it even ten feet I never try to ride the bike yet pls my name is oscar avs
see this video for M5 display settings: ruclips.net/video/pnaEkvOyHwE/видео.html If this does not work then ask manufacturer how to reset to factory default settings
According to manual error code 10 is communication reception which not sure what that means. Check throttle, screen connection to controller? See full manual drive.google.com/file/d/11lAw9iM5LSeClU6BIZ9uhWouXFD8nR_3/view?usp=share_link
P09 Zero Start is simply allowing the throttle to power you off from a standing still position (you don't have to get the bike moving yourself first).
Ok
How do you enbale throttle and pedal assist
Excellent video
Glad it was helpful
Man, you got that thing memorized 😂
Yes
I can't wait until they make a more powerful version, one that goes up to 40mph! I love the fact that the bike is foldable!
No ebike that is 48V is able to get to 40 mph. Closest you can get to is 52v ebike with 1000w or 1500w motor will get you to 37-39mph. To get to 40 mph you will need 2000w and 60V and that bike will weight 135 lbs
Very very helpful. Thank you
Glad i could help
Changing the tire size made a big as$ difference thank you. Keep up the good work. Is there a white cable in the box to control the speed ??
Changing tire size didn’t change the top speed like on some of my other ebikes. No white wire
@@BRichSolutionI unhooked white wire then displays would not show speed
ridstar h20 pro Good afternoon! Tell me a quality product! Is it well made, high-quality?
H20 pro is nearly the same bike has MG01 except larger front headlight and some frames the rear shock is different position. Yes good quality
I Ritch, I have 2 other e bikes that have great pedal assist right from the start where the Ridstar you must pedal a few times before assist kicks in. Even at speed when I let off throttle and pedal the assist will kick in when it wants to. I have bought a new controller and no difference. I found a video that explained all settings and set for max assist but it's just a little better. ??
Some bikes PAS kick is much quicker then other and sensitivity can be adjusted in the settings. I wonder if the cadence sensor on crank has too few magnets and the sensors is limited. Maybe try changing sensor or increasing the setting for the number magnets to fool the controller?
In your video you left the number of magnets set to one witch was the default. Does your bike respond as good as your other bikes?@@BRichSolution
Where can I get the manual for the ridstar mg-01 please help
Does the mg01 not use this screen? a Link to the full user manual is below:
drive.google.com/file/d/11lAw9iM5LSeClU6BIZ9uhWouXFD8nR_3/view?usp=share_link
I forgot how to put it in walk mode? Please advise. thanks
Try holding + button for 3 seconds. If that doesn’t work then try - button
@@BRichSolution thanks. Yes - button worked but it walks way to fast.
Hi B Rich love your videos. I have purchased this bike after watching the unboxing and review video of yours. To be clear p17 cruise is that throttle on and off? ( I live in Australia and it legally cannot be ridden with a throttle in public areas) so I need to disable the throttle. My bike hasn’t arrived yet and like you will raise the stem.
I believe it is p17 to disable the throttle. See this link for full manual
drive.google.com/file/d/11lAw9iM5LSeClU6BIZ9uhWouXFD8nR_3/view?usp=share_link
I put this on my ouxi v8 1.0 or 2.0 but how do i get the speed to 25 because theirs no speed setting
See this video to get max speed. Change amps to highest it will go
ruclips.net/video/pnaEkvOyHwE/видео.html
@@BRichSolution no i want it to stay at 25 kmhs
Any way to auto on this display on key turn?
No, i wish there was
Please help!! I have a new model M5 display on my ridstar it has P0 1 Thur 0 and P1. 1 thru 0. Most of the settings are the same as the old one. P0 8 is speed control. Problem is I was messing around with it and now I have no throttle.
Change p10 to 2 so throttle and pedal assist are active
See video
ruclips.net/video/pnaEkvOyHwE/видео.html
Change p10 to 2 so throttle and pedal assist are activated see video for ruclips.net/video/pnaEkvOyHwE/видео.html
صحيح 👍 @@BRichSolution
@@BRichSolution
Speed is about 25 km/h
When changing the speed, a four-digit code is requested
Please help, guys
I want to increase the speed to 40
Thanks for this! Can you tell me the best settings for good pedal assist from a dead start and still have max speed throttle? I would like dial it in to have a faster pedal assist.
PAS mode 5; max assist
In PAS 5 I have 3 settings,000,1,and 2, witch is the choise?@@BRichSolution
My pas 5 only has 000 or 1 or 2 and on 000 I get 29 MPH with throttle on 1 or 2 I only get10.5 MPH with the throttle. Is this the normal??
@@BRichSolution
To factory reset the display : P16 - hold mode and down button until the screen flashes. It will reset all settings to default.
Mine had P08 032 and would not let us change it to anything else. Had to call the ebike manufacturer and he had us do the above steps which factory reset it. It was then back to max speed of 100 on P08.
Great information, thanks for sharing
Just bought the Ridstar 48v 1000w foldable.
But it will not accept any input changes PO1 thru P20. The M5 display shows the changes but the bike reacts exactly the same to manual pedal and throttle inputs.
Also, I can turn it on and start the bike up without the battery key inserted or in either of it's two positions??
Any idea's anyone?
doesn't sound right. Reach out the manufacturer or seller and tell them the issue. Sounds like bad Controller?
Hi I have similar problem on my ridstar but not with every settings. But for example I change P11 or P12 or p14 and bike reacts exactly the same regardless of values in settings. Did you find any solution for that?
@@mrgodzio1750
I finally emailed the manufacturer in Thailand.
They sent me a new controller after I complained about the inability to self customize. They initially said it was a safety issue. I threatened to return since I bought it on Amazon.
That changed their tone.
And sent me an extra battery to keep me happy. 😁👍
How do I do cruise control ? I broke my M5 on my ridstar got a new one and it finally give me cruise ? I saw that if it’s on you can throttle the bike and the hold down button at the same time
Looks like p17 activates cruise controls see full user manual drive.google.com/file/d/11lAw9iM5LSeClU6BIZ9uhWouXFD8nR_3/view?usp=share_link
Speed is about 25 km/h
When changing the speed, a four-digit code is requested
Please help, guys
I want to increase the speed to 40
Try 1212 if that does not work ask seller
i have a problem with my gas push button , how to fix that?
Did it get wet or stop working?
I held the down and the mode button now my bike wont go over 15.6
Did you hold down the + and - button as the same time to get to advanced menu?
@@BRichSolution yea the speed is locked at 25 kmh
Setting Current Limit (P14) to 22Ampere give you more current (if your battery can provide enough) and you get more power, but if the controller isn't designed to support 22A (you have to check on your controller specs)you will break it quickly, specially if you ask that current for long time, so i will suggest to keep it at default value, or just few amp more.
20A is controllers max output so I dialed it back to 20A and all is well
Hi, my display is only @ 16 which is confusing. I did install a turning signal and moved the display around on the handle bar so does that have something to do with it? I want to completely reset this screen back to all factory setting. Please help😅 thanks
I did not see factory reset option in the manual. Use the video to set each option to factory setting.
Link to full manual drive.google.com/file/d/11lAw9iM5LSeClU6BIZ9uhWouXFD8nR_3/view?usp=share_link
I have the 1000w 20 ah. Is the link you sent me applicable to it?
do you have the chinese version of the manual (so pre-translated)?
it's a bit difficult to read the translated version 😅😅
I do not, ask seller
I have 5 miles on mine and two days later went to ride it and it will not power up. Checked the battery and it is fully charged with 54.4 volts. Any suggestions?
Will it accelerate when pedaling? I had another ebike do this to me and throttle died
No nothing. No head or tail lights, no horn.
@@BRichSolution
I have the Ridstar H20...just arrived. I went in to the advanced settings as described and changed the distance to km, and screen brightness. I'm a bit concerned that P05 which in the video shows to be set at 01....mine is set to 05. Toggling up and down does not allow me to change that value to 01. So my first question is....what does P05 control and secondly...is the setting of 05 correct or not?
See full user manual p05 is help bit file which i believe allow 0-3 PAS mode or 0-5 PAS. drive.google.com/file/d/11lAw9iM5LSeClU6BIZ9uhWouXFD8nR_3/view?usp=share_link
P5 is number of gears, it’s set at 5 you can make 3 or 9. Not sure why it changes the first number when you hit down compared to cycling through by pressing up. In other words idk the difference between 0.05 and 1.05
hello i have this M5 pannel too, but i cannot go to settings when i press down on arrow buttons. it kinda asks me a code with 3 digits could you help me about this ?
Ask manufacturer for code or how to reset
I've seen "6666" as an unlock code, so try "666"
I copied your settings and my h20 not working after that. Any suggestions? Need help. Thank you.
H20 must have different settings then. Put settings back to default and then change each setting individually and test before going to the next setting
@@BRichSolution yeah. I already figured it out. Working now. Thanks.
I just received my new bike and the controller switch is a different style than the one you have to adjust the screen settings. Mine has a + and a - button with out an M to make changes. Also my manual has the older style switch noted. I can get into the screen menu buy cant make any changes. Any suggestions?
Thank you
How do you turn the power on/off to the screen? If you have a power button use the on/of switch to cycle thru options once in the options menu
@@BRichSolution Great information. Thank you very much.
Hi, i have an ouxi V8 with the M5 display, but i cant change all of the settings, only the brightness, speed limit and PAS mode. Any suggestions for a display that will let me change all of the settings? also, the bike only goes 40/42 km/h on GPS, yet the display says 50.. should i just buy a better controller so it goes faster?
Ask seller or manufacturer for password to unlock the speed
@@BRichSolutionthe thing is that i bought it used. So i don't know who to contact..
Witam. Jest taki problem ,lub niema ? Jak cofam rowerem do tyłu to nie idzie płynnie jak na luzie tylko z lekkim oporem ? Klocki nie trzymają ? Może być problem z silnikiem ?
Not sure if that is an issue when in reverse
Tak. Cofam do tyłu i jakby był na biegu ? I jeszcze jedno pytanie moc mam do (PAS3) jak to zmienić ?
How do I switch my odometer from km to mph ?
See video p02
How can i enable pedal assist?
P10 setting. 0 i believe is pedal only, 1 is throttle only and 2 is both. See link to full manual in description below video
Hi I was watching your video about ridstar adjusting the lcd I tried to follow all your numbers but my bike stop running no more I don’t know if I press something wrong & that’s the reason my bike stop running pls if you guide me how to run my bike back I had the 1000w 48v15ah ridstar I just finished assembling the bike & I start adjusting control panel LCD while watching you & unfortunately my bike stop running & I didn’t put any mile on it even ten feet I never try to ride the bike yet pls my name is oscar avs
see this video for M5 display settings: ruclips.net/video/pnaEkvOyHwE/видео.html If this does not work then ask manufacturer how to reset to factory default settings
Go to pas5 and set it to 000
Go to p10 set to 2
i have error code 10 how to fix?
According to manual error code 10 is communication reception which not sure what that means. Check throttle, screen connection to controller? See full manual drive.google.com/file/d/11lAw9iM5LSeClU6BIZ9uhWouXFD8nR_3/view?usp=share_link
Short in lcd line . wiggle around
Any way to restore M5 to factory default? My young nephew started messing around with the menu and now pas1 doesn’t work. Ty
See manual in description under video there is reset to factory settings
@@BRichSolution I downloaded pdf file you included. Subscribed. Ok thank you
P 16 hold mode button untill the screen flashes
@@jimtrump1450 thank you very much.
3:07
P17 is cruise control option for on or off
@@BRichSolution Whenever i do the up and down combo it gives me a screen of “9999”
Dont you mean Ridstar? 😂
Yes ridstar
@@BRichSolution I thought you said Ridestar
@@BRichSolution Rid Star ⭐ or Ride ✨ Star
@BRichSolution what does P14 do again?? I have it at 12 does that effect speed??
@@BRichSolutionI have a 500 watt senada drifter whay should my P14 be at?? And I changed my P18 to 150 and it does 43mph is that accurate??
It's rid star, not ride star.
You’re right
Who cares??@@BRichSolution