I have a problem, I hope you help, sir. The gsm sim 900 is working normally, and I can send messages and they appear in the monitor normally, but when you press the restart button, the gsm does not work and the question mark appears in the monitor unless you raise the code again
Hi Ali I tried this with a Sim900 and Mega like you, on serial1, serial2...with or without GND, same wiring Never receive with AT the OK, have you an idea ? Is it possible you put hear code program ? Thanks
When serial monitor does not print At commands it means your Sim900 is not connected or maybe it is not receiving enough power. Try also to change baud rates.
Thank you, Very useful video.
Thank u very hrlpful
I have a problem, I hope you help, sir. The gsm sim 900 is working normally, and I can send messages and they appear in the monitor normally, but when you press the restart button, the gsm does not work and the question mark appears in the monitor unless you raise the code again
عند قطع تيار على gsm يجب ان ضغط من جديد على زر تشغيل و اعادة رفع البرامج من جديد هل هناك حل لهذه المشكلة
i must put a sim card to the GSM?
and the second question i use Arduino uno? so where i should connect the 19 and 18 pins?
Hello, yes you must put a sim card, it can be any sim card. For Arduino uno, you can connect the wires to TX and RX of Arduino uno
لازم يكون فيه اشتراك نت, اشترك باي باقة انترنت
U have to use software serial library
ماشاء الله طرحك جميل واتمنى لك التوفيق
ملاحظة اتمنى انك تستخدم سكتش واحد والباقي تكتبهم نوت عشان تكون الصورة اوضح
شكرا أخي
when i press AT on the serial monitor , I am getting infinite number of Y^ on the screen. Can u please tell us what's the problem is
....
Hey,
How can I catch the RING event and decline the call?
Can I power sim900 with 12V, 2A dc adapter?
I don't think you can do so it should be 5v , check the ratings
Nothing is appearing on when the screen when i type AT.
Do you have a solution for that?
Your GSM sheild is not responding there should be a connection problem between it and Arduino. Check also your Baud rate
@@alim25061 I changed the baud rate to 19200 also swap the ground pin wire,it worked but still no display on serial monitor when AT is pressed
hye, what is the character to terminate the message??
I think it was □
Hi Ali
I tried this with a Sim900 and Mega like you, on serial1, serial2...with or without GND, same wiring
Never receive with AT the OK, have you an idea ?
Is it possible you put hear code program ?
Thanks
Hi, put your email here so i can send you. The link works with no issues
@@alim25061 Hi Ali, I have a SIM card problem, program and wiring was ok
I changed card and work now. Thank s for your easy and simple tutorial
@@mariokan7991 hey hello, what was the problem with the SIM card
الف شكر على المعلومات حاولت استخدام ال CODES لكن هناك error ; could not create the sketch
ممكن النصيحة
اهلا بك، اسف لا اعرف السبب
Can you please the code or send the link for downloading??
New Link provided
WHERE DOES THE ARDUINO GET ITS POWER SOURCE
From usb 5v
Gprs support?
yes
Do you need to solder r13 for using gpr5?
download link is not working.
It is working I have checked it
can you please post your code here
New link provided
بليز عندي مشكل سيريال مونيتور ما تظهر فيها النتائج شو السبب؟؟؟
When serial monitor does not print At commands it means your Sim900 is not connected or maybe it is not receiving enough power. Try also to change baud rates.
@@alim25061 But I tried code call voice Why type AT but do not show as well as the result But I could call voice but send message I couldn't
@@maysoonmissou6371 I am not sure why maybe the problem with your Arduino IDE
@@alim25061 okay but The number in front of CMGS is different by state?
ماشاء الله اتمنى بالتوفيق ممكن رقم التليفون