Has anyone got these files still I have a nvem v2 and I'm getting a pop up reading "choose bin file", I'm still seeing packets sending and receiving, but mach3 wont talk to the controller Thanks for any help
Sorry for my English, I am translating by translator. The same problem with NVEM 2. There is no firmware file on the manufacturer's website. If you flash the firmware from the first version, the functions of the second version will disappear, the remote control connection nvmpg... If anyone knows where to get the firmware for the second version, I will be grateful. Unfortunately, I couldn't find it on the Internet.
Sorry for my English, translating through a translator, hoping to help other people. I am answering my own question. Solved the problem with the NVMPG remote control. The firmware in the archive is working NVEM V2. When flashing, set the necessary parameters with checkmarks and flash. Then it became possible to install a plugin from the manufacturer (all plugins began to fit), but the remote still did not work. In order for the remote to work, I had to spend three days of my life and go through all the possible options. The solution turned out to be simple. It is necessary to supply a separate 5V power supply to the remote control, and connect the ground wire to the common ground wire of the board. Be sure to disconnect the 5V power supply from the controller and apply it separately. Good luck.
3 года назад
@@vitaliyl81 Hi yes, i used the archive with a NVEM V2 controller. Could you share a picture with the right checkmarks that you have used? Thank you
@ Unfortunately, I'm not near the controller right now, but I remember all the menu items. My settings appeared after the program detected the controller. I selected the board model (NVEM 2), frequency (300) and number of axes (6). Translation of Chinese buttons + symbols. If you select the wrong number of axes, the firmware will not be fully flooded and will stop. You can simply reboot the board and try again. With correct firmware, the board will reboot and start. The controller is defined differently depending on the plugin version. But to my surprise, after flashing all the plugins began to fit. (and initially only from disk and NVEM_DigitalDream1123.dll) The button at the bottom left in the program shows the version of the controller, the button at the bottom right offers to select the firmware and immediately flashes it. I noticed this feature. When you install a plugin, you need to replace it, not add it. If you add more than two additional plugins, mach3 will stop connecting to the controller until you reinstall the program. Hope it helped.
@@yurirychkov7188 Добрый день. Ссылка на прошивку есть в комментариях. Там архив и прошивки, там же есть модули и программа для прошивки. Прошивается либо через мач3, либо через программу прошивальщик. Через мач3 просто, при подключении с правильным модулем, мач напишет что нужен Бин файл. Выбираете его и все. При прошивальщике, если не ошибаюсь, нужно выбрать количество осей, частоту и прошивку. Прошивку ещё находил на форуме китайском. Если не найдете, могу вам поискать.
you also have the same problem? unfortunately I haven't solved anything yet. nobody can give me the firmware that the card is asking me and not even the supplier answers me anymore. I started a chat with a person who should provide me with something that he thinks should solve the problem, but wants to get paid too much. who knows if he really has the solution
4 года назад
@@lucasieni-lc3hn YES! here you have all files you need to solve this problem www.filedropper.com/nvemfiles
@@lucasieni-lc3hn ciao Luca, avresti il link del firmware per la versione USB? Sul sito mi dà "Page 404 not found", non riesco a trovare il firmware da nessuna parte 😔
@@lucasieni-lc3hn Luca hi. I cannot subscribe to filedropper. Is there a way you could send me these binary files for NVEM V2, please? My CNC is rendered useless.
Has anyone got these files still I have a nvem v2 and I'm getting a pop up reading "choose bin file", I'm still seeing packets sending and receiving, but mach3 wont talk to the controller
Thanks for any help
Sorry for my English, I am translating by translator. The same problem with NVEM 2. There is no firmware file on the manufacturer's website. If you flash the firmware from the first version, the functions of the second version will disappear, the remote control connection nvmpg... If anyone knows where to get the firmware for the second version, I will be grateful. Unfortunately, I couldn't find it on the Internet.
Sorry for my English, translating through a translator, hoping to help other people. I am answering my own question. Solved the problem with the NVMPG remote control. The firmware in the archive is working NVEM V2. When flashing, set the necessary parameters with checkmarks and flash. Then it became possible to install a plugin from the manufacturer (all plugins began to fit), but the remote still did not work. In order for the remote to work, I had to spend three days of my life and go through all the possible options. The solution turned out to be simple. It is necessary to supply a separate 5V power supply to the remote control, and connect the ground wire to the common ground wire of the board. Be sure to disconnect the 5V power supply from the controller and apply it separately. Good luck.
@@vitaliyl81 Hi yes, i used the archive with a NVEM V2 controller. Could you share a picture with the right checkmarks that you have used? Thank you
@ Unfortunately, I'm not near the controller right now, but I remember all the menu items. My settings appeared after the program detected the controller. I selected the board model (NVEM 2), frequency (300) and number of axes (6). Translation of Chinese buttons + symbols. If you select the wrong number of axes, the firmware will not be fully flooded and will stop. You can simply reboot the board and try again. With correct firmware, the board will reboot and start. The controller is defined differently depending on the plugin version. But to my surprise, after flashing all the plugins began to fit. (and initially only from disk and NVEM_DigitalDream1123.dll)
The button at the bottom left in the program shows the version of the controller, the button at the bottom right offers to select the firmware and immediately flashes it. I noticed this feature. When you install a plugin, you need to replace it, not add it. If you add more than two additional plugins, mach3 will stop connecting to the controller until you reinstall the program. Hope it helped.
@@vitaliyl81 , Здравствуйте! А где можно скачать прошивки и как правильно прошивать?
@@yurirychkov7188 Добрый день. Ссылка на прошивку есть в комментариях. Там архив и прошивки, там же есть модули и программа для прошивки. Прошивается либо через мач3, либо через программу прошивальщик. Через мач3 просто, при подключении с правильным модулем, мач напишет что нужен Бин файл. Выбираете его и все. При прошивальщике, если не ошибаюсь, нужно выбрать количество осей, частоту и прошивку. Прошивку ещё находил на форуме китайском. Если не найдете, могу вам поискать.
Have you solved this problem?
you also have the same problem?
unfortunately I haven't solved anything yet.
nobody can give me the firmware that the card is asking me and not even the supplier answers me anymore.
I started a chat with a person who should provide me with something that he thinks should solve the problem, but wants to get paid too much.
who knows if he really has the solution
@@lucasieni-lc3hn YES! here you have all files you need to solve this problem www.filedropper.com/nvemfiles
@ Hello guys! I can't solve it .Can you help me pls
@@ΚωνσταντινοςΒατμανιδης have you download the files? Which is your problem?
@ i open the programm and its in chinese
I have the same problem and I can't solve it
eccoti il link per scaricare il file bin www.filedropper.com/nvem-stf2ethprodenc
metti un mi piace se risolverai il problema, Grazie
@@lucasieni-lc3hn ciao Luca, avresti il link del firmware per la versione USB? Sul sito mi dà "Page 404 not found", non riesco a trovare il firmware da nessuna parte 😔
@@samanthapagani4766 purtroppo ho solo la versione per Ethernet
@@lucasieni-lc3hn ok grazie mille
@@lucasieni-lc3hn Luca hi. I cannot subscribe to filedropper. Is there a way you could send me these binary files for NVEM V2, please? My CNC is rendered useless.
ciao Luca ho lo stesso problema , puoi inviarmi il firmware ? mitikoge@gmail.com. grazie mille.