How to use a nanoVNA as a grid dip meter.

Поделиться
HTML-код
  • Опубликовано: 24 ноя 2024

Комментарии • 48

  • @donepearce
    @donepearce 7 месяцев назад +7

    You should get some connector savers. They look like an attenuator but they have a straight through connection. Just wind them onto the two VNA ports and leave them there. No need to use jumpers that way.

    • @gerrykavanagh
      @gerrykavanagh 7 месяцев назад +2

      was going to recommend this myself. I went the extra step of 3D printing a little attachment that slips over the hex nuts of the SMA-savers to keep them from turning

  • @W4BIN
    @W4BIN 8 месяцев назад +4

    I wound mine around a 1.25" pill bottle and put the SMA connector directly to the two inch long wires. (no coax) If I can connect it, I can replace it. I used "liquid tape" to bind the two turns and the two inch long lead into a rod. I used about #20 enameled wire. I use mine like a wand holding the MiniVNA-Pro with coil as a hand held probe. (no vise) Ron W4BIN

  • @johnwest7993
    @johnwest7993 7 месяцев назад +11

    That $53.95 ad for a set of pick-up loops for an MFJ cracked me up! That's as much as an entire NanoVNA. Thanks for the videos. Some good hams, including you are turning into RUclips Elmers and creating a body of work that can teach hams of any level how to build, how to repair, how to design, even everything about atmospherics, or tips and tricks. And the info just grows continually. It's a wonderful thing. Now, if we could just get rid of some of the Baofeng unboxing videos. :)
    Thank you.

    • @frankthetank3342
      @frankthetank3342 7 месяцев назад +1

      Based on MFJ coils, and older Kenwood and other brands, having multiple sizes, I assumed the coils were tuned. Guess I'll be making coils now!

    • @javabeanz8549
      @javabeanz8549 7 месяцев назад +1

      Hey now! Those CCRs are getting lots of new blood into radio, and a bunch of us old dogs back into radio. Studying for my tech ticket currently. Without a Baofeng UV-5R and a GMRS-9R, I certainly would not have been able to afford to get started again.

    • @johnwest7993
      @johnwest7993 7 месяцев назад

      @@javabeanz8549, you'll need to spell out what a CCR is. I've found hundreds of definitions, from constant current regulators to Credence Clearwater Revival.

    • @johnwest7993
      @johnwest7993 7 месяцев назад +1

      @@javabeanz8549, I have nothing at all against the cheap radios, unless they have illegal harmonic output. I have 6 or 8 of them. What I've grown weary of is video after video of kids who know essentially nothing about radio simply opening up the boxes and talking about doing just that. I already know how to open boxes. I've seen far too many such videos as I was trying to learn about the actual characteristics of the radios. They waste everyone's time. It takes a while to sort through the garbage channels to find channels like this one with actual content.

    • @javabeanz8549
      @javabeanz8549 7 месяцев назад

      ​@@johnwest7993 oh yes, the Wannabes... they want to be influencers, so they bought a $25 to $60 radio on Amazon, Temu, etc, and opened the box and read through the tiny manual that comes with most of them, played with the radio for a few minutes and think that they are experts. I think that we can find their kind in many areas. I have a collection here, Bao Feng, Tidradio, B-Tech, QYT, Radioddity. In fact, there's supposed to be another radio on UPS today. And no, I won't be doing an unboxing video ;0) I was into CBs and Shortwave listening 40 years ago or so. Now I am more into GMRD, and want to get my technician ticket so I can get on UHF and VHF. I really don't have enough property to get into HF, and besides that, I can deal with all the noise coming in on skip, it just gives me a headache anymore.

  • @Jerrythenerdful
    @Jerrythenerdful 7 месяцев назад +2

    This idea came from a magazine article years ago. MFJ copied it and sold it as an adaptor for their antenna analyzers.
    It is actually better just to connect the trap or resonant circuit to the VNA directly and measure the impedance of the trap or resonant circuit. Just use a short jumper with a cable separation at the far end with alligator clips. Calibrate that with an OSL calibration. The VNA can measure the actual trap impedance and Q using a direct connection, I do it every week for testing RF chokes.
    You don't have to spend $53 for a useless hunk of wire you can find in your junk box. You can make a jumper or adaptor for a jumper with clip leads and read the actual impedance with a direct connection. It can do anything this can do and better, and you save almost $60!!

    • @RicksHamShack
      @RicksHamShack  7 месяцев назад +2

      I have tried measuring directly from the S11 port, for some reason the nano shows them a few hundred KHz low on frequency. Might be an error on my part.

  • @qzorn4440
    @qzorn4440 7 месяцев назад +1

    Amazing results of the nanoVNA. Thank you.

  • @acestudioscouk-Ace-G0ACE
    @acestudioscouk-Ace-G0ACE 2 месяца назад

    A very useful video and well explained, thank-you. I may well make one of these.

  • @TheSmokinApe
    @TheSmokinApe 7 месяцев назад +2

    Very cool 👍

    • @RicksHamShack
      @RicksHamShack  7 месяцев назад

      Thanks Ape! I'm about to head over to your channel and watch the St. Patrick's day toroid...

  • @gerrykavanagh
    @gerrykavanagh 7 месяцев назад

    Excellent video! Thanks

  • @frequencywatchers
    @frequencywatchers 4 месяца назад +1

    This Is Actually very Helpful, THANK YOU VERY MUCH FOR THE VIDEO AND INFORMATION!
    Greetings From Me !

  • @Steve-GM0HUU
    @Steve-GM0HUU 7 месяцев назад +1

    👍Thanks for posting.

  • @Bazzawombat
    @Bazzawombat 7 месяцев назад +2

    What was the nano vna set to? Phase, swr and log mag? Was out of focus so I couldn't,t read

    • @javabeanz8549
      @javabeanz8549 7 месяцев назад

      Mine came with such a small manual, I am not even sure what all functions it has, I have just been trying to test some GMRS antennas with it. After watching this video, I see that I need to find instructions on how to calibrate it properly.

  • @texaslarry1048
    @texaslarry1048 2 месяца назад

    Is it possible to test field strength with my VNA?

  • @ve6wo
    @ve6wo 7 месяцев назад

    This is great stuff! Subscribed :-)

  • @bazzaar1869
    @bazzaar1869 8 месяцев назад +1

    What this wont replicate is the very high impedance the grid dip meter operated at(meg ohms) because you are now coupling into a 50ohm test system. This means the circuit under test will be loaded and damped much more than with the GDM. What this might mean in practical terms is hard to say, in use the circuit might react at slightly different frequency to that measured with the Tiny VNA. The tank circuit in that regen receiver might not have the Q you were expecting! :)

    • @dayleedwards3521
      @dayleedwards3521 7 месяцев назад +1

      Not quite. The coupling coefficient between coils will allow an impedance match as seen between the low and high frequency trap measurements, the coupling increases as the frequency rises, increasing loading. Not ideal but it will give a good indication. A real GDO still reigns supreme.

    • @Steve-GM0HUU
      @Steve-GM0HUU 7 месяцев назад +1

      If I have time, I may try NanoVNA vs GDO later. I found that I can very accurately measure the dip frequency on a GDO by zero beating the GDO with a calibrated receiver. It would be interesting to see if there any difference between the Nano and the GDO.

    • @lmantuano6986
      @lmantuano6986 7 месяцев назад

      @@Steve-GM0HUU that would be good if you could. The poster did a good and detailed job at the construction of it, but left it a bit thin on the use-cases side.. I hope he would consider doing a Part 2..
      Thanx-n-73
      lm-VK3OLA

    • @Steve-GM0HUU
      @Steve-GM0HUU 7 месяцев назад +1

      @@lmantuano6986 I did a quick test. I used my old TRIO DM-801 to get a dip on a 12m trap. My receiver indicated dip frequency of 25.253MHz. I used my NanoVNA v2.2 to get a dip on on the same trap and the same receiver indicated a dip frequency of 25.525MHz.
      OK, not a very accurate test but it did indicate a GDO vs NanoVNA difference of 272KHz. Assuming one of the methods is accurate, 272KHz is a approx. a 1% error.

  • @kevtheskin
    @kevtheskin 2 месяца назад

    Hi there What formats have you set for the traces please

    • @RicksHamShack
      @RicksHamShack  2 месяца назад

      @@kevtheskin Resistance and phase.

    • @kevtheskin
      @kevtheskin 2 месяца назад

      @RicksHamShack Hi Rick thanks for the reply. Is resistance in the formats advance settings. Would you mind doing a wee video with the setup of the traces please. Cheers 73 Kev

    • @kevtheskin
      @kevtheskin Месяц назад

      @@RicksHamShack Sorry to bother you again. I cant get this to work . I have 2x traces set one with phase and the other on resistance. 10mhz to 500mhz and nothing? Can you help?

    • @RicksHamShack
      @RicksHamShack  Месяц назад

      @@kevtheskin ruclips.net/video/xsFG655zEp0/видео.html That video shows how to change the format of the trace, hope that helps.

    • @kevtheskin
      @kevtheskin Месяц назад

      @RicksHamShack Hi Rick, Thanks for replying. I have set my nano up with phase and resistance and a loop and nothing shows on my nano when held over the trap. What scale divisions are you using please. 73 Kev mm0kjg

  • @garylanders1470
    @garylanders1470 8 месяцев назад

    Sweet!

  • @barrybogart5436
    @barrybogart5436 7 месяцев назад

    Interesting. I was first licensed in '57 so am familiar with GDOs. actually I started collecting them at hamfests and have MFJ, Heath, Kenwood and Simpson ones. (I'd like to get an Eico with a real vacuum tube in it.). Anyway I also have a Nano and your demo was very interesting. But all my GDOs have a series of plug-in coils with many more turns and I wondered what difference that made compare to your little homebrew one. Is it because of the wideband sensitivity of the Nano? Does Q enter into it?
    73

    • @ElPasoTubeAmps
      @ElPasoTubeAmps 3 месяца назад

      I have been using a grid dip oscillator, GDO, for a long time also. Still use them, even tonight, and have found the Barker & Williamson (B&W) GDO very good and uses an acorn tube. I see them on Ebay and maybe you would enjoy one of those for your tube collection and use. I started with my general license in '63. Been a great hobby for a long time. I don't know how to use a GDO for determining Q but a nano VNA can be used to measure Q. I also did that tonight on a B&W 850A tank coil for a friend. B&W advertises their unloaded Q to be 50 or better. I measured it at 70 on the 20M tap. Not too bad. 73 WA4QGA

  • @fredshead3956
    @fredshead3956 8 месяцев назад +1

    Hi Rick, i am trying to test a Key Fob, RF type for central locking on car, i am told it can be done with a nano VNA, but i haven't managred to do it yet...Fred in Uk.

    • @RicksHamShack
      @RicksHamShack  8 месяцев назад +2

      Most of them are 315 MHz. I test them with a TPMS tool that has that feature. I'll see if my loop picks up the fobs I have and report back.

    • @fredshead3956
      @fredshead3956 8 месяцев назад

      @@RicksHamShack Thanks Rick..

    • @RobertSzasz
      @RobertSzasz 8 месяцев назад

      Probably better to use a rtl-sdr for quick "does it transmit" when you have a rough idea of the frequency. (You're only going to get 2mhz instantaneous bandwidth, but you can check various bands quickly)

    • @ElPasoTubeAmps
      @ElPasoTubeAmps 7 месяцев назад

      If your scope is high enough frequency, you can put a loop on the end of an oscilloscope probe and hold it to the
      case of the Fob and see if it is transmitting RF.

    • @fredshead3956
      @fredshead3956 7 месяцев назад

      @@ElPasoTubeAmps Yes ok i see what you mean, i will give it a try thanks...F.

  • @KF0NNQ
    @KF0NNQ 7 месяцев назад

    Good video and informative. 73, KF0NNQ.

  • @wiwingmargahayu6831
    @wiwingmargahayu6831 7 месяцев назад

    new telco operator ????

  • @G0USL
    @G0USL 7 месяцев назад

    Great demo thanks G0USL