Это видео недоступно.
Сожалеем об этом.
SCHNEIDER ATV312 VFD CONFIGURE FOR DI(START/STOP)2WIRE,3WIRE AND SPEED PARAMETERS
HTML-код
- Опубликовано: 14 июн 2020
- range of product
Altivar 312
product or component type
Variable speed drive
product destination
Asynchronous motors
product specific application
Simple machine
assembly style
With heat sink
component name
ATV312
motor power kW
7.5 kW
motor power hp
10 hp
[Us] rated supply voltage
380...500 V - 15...10 %
supply frequency
50...60 Hz - 5...5 %
network number of phases
3 phases
line current
27.7 A at 380 V, Isc = 22 kA
21 A at 500 V
EMC filter
Integrated
apparent power
18 kVA
maximum transient current
25.5 A for 60 s
power dissipation in W
269 W at nominal load
speed range
1…50
asynchronous motor control profile
Sensorless flux vector control with PWM type motor control signal
Factory set : constant torque
electrical connection
Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 2.5 mm² AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 16 mm² AWG 6
supply
Internal supply for logic inputs: 19...30 V 100 mA, protection type: overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm): 10...10.8 V 10 mA, protection type: overload and short-circuit protection
communication port protocol
CANopen
Modbus
IP degree of protection
IP20 on upper part without cover plate
IP21 on connection terminals
IP31 on upper part
IP41 on upper part
option card
Communication card for CANopen daisy chain
Communication card for DeviceNet
Communication card for Fipio
Communication card for Modbus TCP
बहुत ही अच्छा सपोटरजी
Very nice video
👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
very good bro
this same function will work on altivar 31 or not
What I do if main voltage showing fluctuation from 250 to 276volts in vfd how I slove this problem... It is showing alarm OFS
I couldn't see local option while setting then only appear 2c and 3c.how can i go further.
Sir atv212 me potionmeter aur push botton ki programming bato pls
Multi siped me rokna ho to kon sa perameter dalna prega sir
Sir nlp aa rahi hai. 110 volt pe chala sakte hai kya . Range 220 240 likhi hai
is it available in Chittagong I need it
Sar mere pass fuel test match hai jismein ke 5 HP aur Dhai HP ki motor hai uske andar hai AC drive sainator ki three face Ki Lagi Hui Hai use single face Kaise Hogi
Thx
Sir
But vfd programing is very complex hai
Schinder ki. Vfd
Hoples vfd hai .....!!!!
सर मेरे पास 5 HP का Ac सोलर है उसका vfd सुबह मे ठंडी के दिन मे चलता नहीं जैसे की सुबह के 10 बजे तक और एकदम से बादल या फिर तेज हवा के कारण vfd मे LL दिखाता है दिनभर ये चालू बंद होता है schneider vfd है
Sir VFD ko auto me kise set kar ke chalate hai
Left aur right run kaise yoga.
Sir muje 2 wire setting me speed settings kese Karu autoconstant speed
Sir vfd ka speed 20 par lock kiya he. use 40 tak kaise bhaye
Altivar 31 ka connection selecter switch sai kerna hai
Mine is saying rdy after 2-3 times running it shows INF and lift stop running.. then I have to power off and on again than again rdy and after 2-3 running showing INF again
Pls help
Sir, Reverse connection kaise kar na ha ?
Sir mortar ki speed kam kese set krke rakhe
4to20ma parameters tell me sir
Sir Running time me OLF vf batane Lagta or motor band ho jati hai
Complete program video in hindi same drive
Podrá en español por fa
Hello Sir
Drc parameter setting
Hello sir
Hello
Double speed kese chalaye
Sir motor ko start karne ke liye VFD me konse parameters fill karte hai or kese
Only Start krne ke liye 2 parameters selection krne hote hai phella start with keypad/terminal agar aap terminal selection chahte hai to dusra parameter aapko 2/3 wire selection ka dalna pdega
Nst ko riset kaise kare
reverse forward process
Sir is vfd ka price kya h
Sir start problem atv312 5hp
Hamari Drive pe jo miter laga vo number mainas Deka rha hai
Sir Aapka mob no mil Sakta hai kya. Kyoki jab VDF ki sat karta hu to bahut samasya aati hai
Hlo sir kya ap sa bath ho skthi ha
Rdy, nst Displays
Brack ka perameter
Scf fault aa rha h... Display pe rdy nhi aa rha
Short circuit ka fault hai.
Check the cables connecting the drive to the motor,and the motor insulation.
Dear nst fault kya hai
If a directional run command (forward or reverse) is present on power up of the drive and the drive is set for 2C (2-wire) with [trn] transition control or 3C (3-wire) control with the LI1 NC stop being open, the drive will show nSt indicating that it will not run.
Agar regular command de rakhi hai tab bhi nst aa jata hai
Sir drive not 0+50 stat
Your question not clear pls clear
😂😂😂😂
Ready nahi arahi hi
Ek baar reset karke parameters full kijiye
Sir kya aap ka whatsapp no de sakte h
S LF Ara hi
Koi parameters rong enter hua hai
Check start command & refrence parameters aur agar fir bhi samjh nahi aaya to reset kardo apne aap default parameters aa jaayenge
Mug apn watapp numper da