Your complete project can be replaced with only one ESP 01 and DHT sensor. Still if you want to have a WiFi bridge, use a NodeMcu in WIFI_AP_STA mode. For such a simple task you used excessive hardware. And before promoting any vendor, first you do place an order and then cover its quality and feedback as well so others can make an informed decision about using the same service. You clearly just added them to cart and didn't order. Never once showed the PCB in your video. Still I'll say good job for the efforts you put.
I want to make this by using nano as transmitter and node mcu has receiver by sending accelerometer data with NRF24L01 help. so, can u help me in any reference to do it... Or what changes I need to do if I use Arduino nano and node mcu....
I use this with UNO (transmitter) and NodeMCU ESP8266 (receiver) and have no problem. But when I use UNO as receiver and NodeMCU as transmitter. It doesn't work. So I searched the internet found out that I need to solder 10uf capacitor to VCC and GND of the NRF24L01 on NodeMCU side. Now I can't upload sketch to NodeMCU when VCC and GND are connected to the module. Did I solder the cap wrong? VCC -> positive of cap and GND -> negative of cap. The module I'm using has antenna connector.
@@HowtoElectronics I uploaded sketch to NodeMCU and then connected vcc&gnd back to the NRF Module. No communication between the transmitter and receiver. I guess capacitor method doesn't work with the module with antenna connector.
@@gokulrajl4664 It's dead. RIP 😆 So I threw it into a trashcan. Anyway, I bought a new one and I can send signal wirelessly in 1 way communication. But I still can't write code to do Bi-Direction communication.
I very informative presentation. Thank you.
Wow, great video ❤❤.
Love from Nepal 🇳🇵 sir
Awesome job bro......
1st viewer....
Wow, such a great project. Was looking for it since long. Thanjs
Yes bro... mst project h
Thank you for your hard work putting this video tutorial together. It is very well done.
Helpful video 👍
Nice video 👍
If I want to connect a NRF24 module with ttgo-t-call then which pin should I chose, that the GSM connection will not interrupt.
good explanation. Good video. Love it.
Your complete project can be replaced with only one ESP 01 and DHT sensor. Still if you want to have a WiFi bridge, use a NodeMcu in WIFI_AP_STA mode.
For such a simple task you used excessive hardware.
And before promoting any vendor, first you do place an order and then cover its quality and feedback as well so others can make an informed decision about using the same service.
You clearly just added them to cart and didn't order. Never once showed the PCB in your video.
Still I'll say good job for the efforts you put.
Abdus Samad, lo que estas recomendando no es valido si se requiere cubrir un rango de distancia grande...
That's good sir nice project
Please suggest me which module used for more then 10 km range transmission
Lora Modules like SX1276 or SX1278.
I want to make this by using nano as transmitter and node mcu has receiver by sending accelerometer data with NRF24L01 help. so, can u help me in any reference to do it... Or what changes I need to do if I use Arduino nano and node mcu....
So you are telling me USING ESP8266 + NRF24L01...you can make a radio controller without using arduino boards?
I would like to make a re.ote controller for drone and car , how can I use esp and nrf without wifi
I use this with UNO (transmitter) and NodeMCU ESP8266 (receiver) and have no problem. But when I use UNO as receiver and NodeMCU as transmitter. It doesn't work. So I searched the internet found out that I need to solder 10uf capacitor to VCC and GND of the NRF24L01 on NodeMCU side. Now I can't upload sketch to NodeMCU when VCC and GND are connected to the module. Did I solder the cap wrong? VCC -> positive of cap and GND -> negative of cap.
The module I'm using has antenna connector.
The capacitor should not be a problem l. After uploading the code solder the capacitor.
@@HowtoElectronics I uploaded sketch to NodeMCU and then connected vcc&gnd back to the NRF Module. No communication between the transmitter and receiver. I guess capacitor method doesn't work with the module with antenna connector.
@@jumbo999614 did u sort that out
@@gokulrajl4664 It's dead. RIP 😆
So I threw it into a trashcan.
Anyway, I bought a new one and I can send signal wirelessly in 1 way communication. But I still can't write code to do Bi-Direction communication.
@@jumbo999614 can u Send me the code and circuit diagram u used? As iam currently working on my final year project it will really help me.
both node mcu can talk to each other
Sir, can i use this library with esp32?
Thank you sir...
Could I make a network using multiple ESP8266?
please make the IoT project using LoRa and arduino IoT Cloud
bro how to install RH_NRF24.h library
Can I use an ESP8266 NRF24L01 + PA + LNA 2.4 GH Wifi Gateway + ESP8266 NRF24L01 + PA + LNA 2.4 GH Sensor Node?
Yes you can. This will give more better access.
@@HowtoElectronics but can I use the same code or does it vary in any way?
can i use this code with blynk cloud ?
Thank you sir, can we transmit a vidio by nrf module ?
May be not
@@HowtoElectronics please, do you have any suggestions module sir ? I want transmit vidio using radio signal
can you give code file (*.ino)?
I don´t have a good english, but this man talk to strange i think