7447 par pin 8 ground (0V) hai aur pin 16 VCC (5V). Commom anode 7-segment par pin 3 ya pin 8 par +V. Common cathode par pin 3 ya pin 8 par ground (0V)
1. check your 7 segment (common anode or cathode?) and use new IC 2. check you point thats should be common. 3. connection from IC to display reconnect
You are great sir..... thankyou so much sir .....itna easy way mai smjhaya
Thank you sir
Good explanation
Keep watching
Ramram,Nemeste. Aap ka explanation behut accha hai. Yeh 7-Segment display jo aap use karte hai, iska pin no. 3 aur 8 intern connect hain. Aap resistance sabd use karte this wrong, this must be resistor. Resistance aur resistor mein differance hai? Resistor woh hai jo aap DEKH aur CHU sakte hai. Restance aap srif MEASURE kar sakte hai. Capacitor aur capacitance ki liye bhi yeh lagu hai. Capacitor ek cheez hoti hai.
One of the best explanation
Nice video sir beautiful voice
Excellent sir 🎉
Sir common cathode keliye bhi 7447 use kartehai hai kya?
it can use for both common cathode or common anode
its working ty😊😊
Enjoy
Sir agar common cathode led segment hai to resistance kaha connect karna padega ya jaha par aapne connect kiya hai wahi pr
no at bottom side ground
@@CircusofPhysics just on opposite side (ground).. right?
yes@@pawan_6954
@@CircusofPhysics thank you so much sir...💫
Sir Battery kaha connect karni hai
7447 par pin 8 ground (0V) hai aur pin 16 VCC (5V). Commom anode 7-segment par pin 3 ya pin 8 par +V. Common cathode par pin 3 ya pin 8 par ground (0V)
Ram Ram sir ji
Sir apne jo ye end me vcc or ground diyaa h bo smjh nhi aaya kyo kiyaa hum 5 volt ki battery se connect krke bhi to verify kr skte h naa
yes you can, +5V is vcc and negative is ground
@@CircusofPhysics thank you so much sir aapki video dekh k hi aaj mera practical perform ho gyaa 🙏🙏😊
Sir aap square wave generator pr bhi aap plz video upload kr dijiye 🙏🙏
@@shashibala1270 God bless you.
Sir 9 volt ki battery lag sktey hen
yes, you can
Sir aapne display Common Anode ka lagaya hai but truth table common cathode ka hai..
Please explain
the only difference is one has to apply 5v other to the ground. no pin configuration is changed.
Sir I have connected my circuit properly but i am not getting the output
1. check your 7 segment (common anode or common cathode) most probably this is main issue. 2. replace 7447 might be already used you are using
How about using 7400 ic gate?
it is possible to make BCD to 7 segment using 7400 but it would be quite complex , I think nearly 11 IC would be required
Components required ki list Bata doge kya please
Sir nahi hua..kya 3.7 volt se jyada dena hoga kya
minimum 5 volt
Same circuit configure kar rahee he but nHi ho raha hai
IC can be damaged due to voltage fluctuations and one of the other reasons is connecting wires' impedance and resistance is large
@@CircusofPhysics sir jumper wirers laga hai toh uss se kuch dikat aa rahi hai ya normal wire use karu
@@VedanshDhomane yes normal wires can be used
Sir plz give me pdf this Experiment.
sir please provide lab manual sheets
Sir isme do ic hota h 7490 & 7447
it is just decoderm 7490 is counter ic
Sir g nahi display ho raha
1. check your 7 segment (common anode or cathode?) and use new IC 2. check you point thats should be common. 3. connection from IC to display reconnect
it giving me only 8
change IC
Jay shree ram bhaiyo
Jay shree ram