Good video sir, and what an easy fix! Don’t even need to take out the gear just take of the side plate. If I come across anyone else with saltiga 2020 problems I will point them to your channel! Thank you!
Have to 1st check, could be oil or grease contaminate a bit much between antireverse and roller contact surface cause little backplay slip ( rub off and try again) good luck.
It is very dangerous to remove the gear this way. Since there is no anti-reverse switch, it can get stuck at the junction with the pinion. This happened to me on a Certate LT and I had to remove the rotor to turn off anti-reverse and free the gears. Or you need something to securely fix the rotor from rotating. By the way, such a connection with screws is very convenient and you can always eliminate the backlash. In smaller sizes, for example 4000 and below, the gear is fixed with a pressed pin, which in the same case will require complex repairs or replacement of the gear.
Thanks for this. I bought a brand new Shimano Twinpower SW 8000 and out of the box, it had a similar knock. Have you tried this on a Twin power reel by any chance ? Interesting to know if the main crown wheel has a screw in configuration as the Certate does.
@matthewlee1383 check and confirm your Twinpower SW8000 handle is joint type or solid piece, if joint type likely have pin play cause us might think gear knocking, because unlike solid piece handle.
Hi @chensam4853 open a monocoque side cover to fix your gear, it will not affect the magseal. Magseal itself already inside the magseal bearing in monocoque cover section. (Except Airbail Line Roller dont touch)
Can buy it at online shops example: ebay, amazon, aliexpress, shopee, hedgehogstudio.co.jp, or local fishing tackle shop can ask. make sure chat them for your reel size.
@eliasnordin8192 no screw. I have 18 daiwa exist LT3000XH similar issue handle play til rotor feel knock, but i fixed by add 1 thin piece washer from SLP work knob spare washer into bottom of pinion gear. Do your rotor have knock play too?
![SHIMANO 19 STRADIC Full bearing [Same 12BB as STELLA] assembly & custom](/img/1.gif)
Good video sir, and what an easy fix! Don’t even need to take out the gear just take of the side plate. If I come across anyone else with saltiga 2020 problems I will point them to your channel!
Thank you!
Thank you @guardiandown2626
interesting, my certate 10000 is tight but antireverse slip about 2mm
Have to 1st check, could be oil or grease contaminate a bit much between antireverse and roller contact surface cause little backplay slip ( rub off and try again) good luck.
It is very dangerous to remove the gear this way.
Since there is no anti-reverse switch, it can get stuck at the junction with the pinion. This happened to me on a Certate LT and I had to remove the rotor to turn off anti-reverse and free the gears. Or you need something to securely fix the rotor from rotating.
By the way, such a connection with screws is very convenient and you can always eliminate the backlash.
In smaller sizes, for example 4000 and below, the gear is fixed with a pressed pin, which in the same case will require complex repairs or replacement of the gear.
Thanks Mate!
Thanks for this. I bought a brand new Shimano Twinpower SW 8000 and out of the box, it had a similar knock.
Have you tried this on a Twin power reel by any chance ? Interesting to know if the main crown wheel has a screw in configuration as the Certate does.
@matthewlee1383 check and confirm your Twinpower SW8000 handle is joint type or solid piece, if joint type likely have pin play cause us might think gear knocking, because unlike solid piece handle.
Hi, open side cover that affect magseal or not ? thanks.
Hi @chensam4853 open a monocoque side cover to fix your gear, it will not affect the magseal. Magseal itself already inside the magseal bearing in monocoque cover section. (Except Airbail Line Roller dont touch)
@@AllenFishingAdventure Thank you Sir.
Where did you buy side plate MQ tools
Can buy it at online shops example: ebay, amazon, aliexpress, shopee, hedgehogstudio.co.jp, or local fishing tackle shop can ask. make sure chat them for your reel size.
Does the certate 19 have the same screws?
For 19 Certate LT5000 and SW LT6000 it's yes same design, gear and shaft with 6 screw design. For LT4000 size model and below are not same.
but do they still have the screws? my 2500 certate have the same handle play@@AllenFishingAdventure
@eliasnordin8192 no screw. I have 18 daiwa exist LT3000XH similar issue handle play til rotor feel knock, but i fixed by add 1 thin piece washer from SLP work knob spare washer into bottom of pinion gear. Do your rotor have knock play too?
Put some loctite on them
Yeah loctite 242 (blue) medium