Great video. Everyone who does this job has the perfect tool to wind back the brake disc so the calliper fits over the new pads. It's the metal edge of one of the used brake pads you just took off. The metal backing of the pad is just thick enough to go into the + on the front of that disc and you can turn it by hand or with a vice grip holding the old brake pad. It's so perfect I'm sure somebody at Honda design must have done this on purpose but nobody put it in the repair guide.
I just did brakes on a 2011 Honda Accord Crossover, the rear calipers were the push in type not screw in. Just a fyi in case you're working on one. Thanks for the video.
Im guessing if you see the big "X" then it must turn, vs push back in. Always something, or a special tool that they want you to buy, to do simple maintenance
In addition to the great information he provided, always clean factory coatings from new and still usable used rotors...they may flash rust lightly on the surface but that is normal and is removed by the pads. Brake rotors rust all the time...it is normal. Also be sure to add the brake grease to the back of the pad that sits between the caliper piston and the rotor...it will prevent brake squeal and help transfer heat back into the caliper.
Dude, your video saved me! I've changed brake pads 3 times in my life, so I thought I knew what I was doing. I was trying to use a damn c-clamp to push that piston back, then i bought a heavy duty spreader, the piston won't budge..I was getting so frustrated, like wtf is wrong..do I need to bleed out the brake line or something. Then I saw your video and I'm like oooooooh got to twist the effing thing...
My buddy. Told me the same thing about low break fluid. I had no idea. I had to change my front brakes and rotors as well. Thanks. Next are the back ones too.
CORRECT SCREWDRIVER to use: JIS (Japan Industrial Standard) which has only one side angle then flat end tip. Everyone is saying to use #3 Phillips which has two angles b4 the flat end tip, look very closely. Now if the rotor screws are rusted, I do not know for sure, but I am guessing JIS makes bits for manual impact screwdriver and air/power tools. All Japanese car manufacturers use JIS screws which are different, so I always used regular screwdrivers bcuz I did not know either. Hope this helps Japanese car owners everywhere.
Those screws that hold the rotors in place will come out pretty easily by putting a #3 phillips screw driver in them (firmly) and give it a couple real Good whacks (the Screw driver) with a hammer & that shock wil bust them loose...works every time! Also, if you have trouble holding the bracket spacers in place while starting the bolts you can put a dab of grease on them to hold them in place while starting your bolts!
I manufactured a tool to turn the caliber in. I took a three quarter inch piece of pipe and ground for nachos in it to make a look like a tee And used a pair of players to turn the caliber back in. It was a simple solution before buying tools
I ALWAYS use 3M or Mission brand silicone paste to lubricate the slider pins which is also a di-electric grease u can use to protect your electrical connectors. Always use a silicone or specially formulated grease that is NOT petroleum based bcuz petroleum makes rubber boots n bushings swell.
Great video. The only thing I'll add is that the brakes should be bleed, even though the system wasn't open. Brake fluid isn't made to last forever. Most brake fluid is recommended to be changed every 50,000-100,000 miles. Worth bleeding the brakes to get new fluid in the entire system. I only use Honda specific fluids, except oil. Their coolant, brake fluid, transmission fluid and power steering are all superior in Honda's because the fluids are engineered specifically for Honda parts.
Great video but I'm having trouble putting the caliber back on but the pistons are not sliding back and forth like when you took the one part to the table
@@regalakitas9498 Exactly. Do people think a screw that small and soft actually is important? Its just for the assembly line work so the rotors stay snug, and dont fall off during production
Great video. Everyone who does this job has the perfect tool to wind back the brake disc so the calliper fits over the new pads. It's the metal edge of one of the used brake pads you just took off. The metal backing of the pad is just thick enough to go into the + on the front of that disc and you can turn it by hand or with a vice grip holding the old brake pad. It's so perfect I'm sure somebody at Honda design must have done this on purpose but nobody put it in the repair guide.
I have the little cheap square tool and it always does the job. Never thought about the brake pad working just as well though. Brilliant.
Awesome sause! I was wondering how I can twist this without a tool!!
I just did brakes on a 2011 Honda Accord Crossover, the rear calipers were the push in type not screw in. Just a fyi in case you're working on one. Thanks for the video.
Me too.
Im guessing if you see the big "X" then it must turn, vs push back in. Always something, or a special tool that they want you to buy, to do simple maintenance
In addition to the great information he provided, always clean factory coatings from new and still usable used rotors...they may flash rust lightly on the surface but that is normal and is removed by the pads. Brake rotors rust all the time...it is normal.
Also be sure to add the brake grease to the back of the pad that sits between the caliper piston and the rotor...it will prevent brake squeal and help transfer heat back into the caliper.
Thank you. Video was right on the money for my 2011 Honda Accord. Also, I used the edge of a 1" Wood Chisel to turn (Clockwise) the Piston back in.
ragsamar that’s clever, I use a pair of needle nose pliers “opened slightly”
Dude, your video saved me! I've changed brake pads 3 times in my life, so I thought I knew what I was doing. I was trying to use a damn c-clamp to push that piston back, then i bought a heavy duty spreader, the piston won't budge..I was getting so frustrated, like wtf is wrong..do I need to bleed out the brake line or something. Then I saw your video and I'm like oooooooh got to twist the effing thing...
My buddy. Told me the same thing about low break fluid. I had no idea. I had to change my front brakes and rotors as well. Thanks. Next are the back ones too.
CORRECT SCREWDRIVER to use: JIS (Japan Industrial Standard) which has only one side angle then flat end tip. Everyone is saying to use #3 Phillips which has two angles b4 the flat end tip, look very closely. Now if the rotor screws are rusted, I do not know for sure, but I am guessing JIS makes bits for manual impact screwdriver and air/power tools. All Japanese car manufacturers use JIS screws which are different, so I always used regular screwdrivers bcuz I did not know either. Hope this helps Japanese car owners everywhere.
Those screws that hold the rotors in place will come out pretty easily by putting a #3 phillips screw driver in them (firmly) and give it a couple real Good whacks (the Screw driver) with a hammer & that shock wil bust them loose...works every time! Also, if you have trouble holding the bracket spacers in place while starting the bolts you can put a dab of grease on them to hold them in place while starting your bolts!
I manufactured a tool to turn the caliber in. I took a three quarter inch piece of pipe and ground for nachos in it to make a look like a tee And used a pair of players to turn the caliber back in. It was a simple solution before buying tools
I ALWAYS use 3M or Mission brand silicone paste to lubricate the slider pins which is also a di-electric grease u can use to protect your electrical connectors. Always use a silicone or specially formulated grease that is NOT petroleum based bcuz petroleum makes rubber boots n bushings swell.
Thanks. Very good video explaining all the stuff I need to know in a good way. I will change my back breaks next week now :)
Great video. The only thing I'll add is that the brakes should be bleed, even though the system wasn't open. Brake fluid isn't made to last forever. Most brake fluid is recommended to be changed every 50,000-100,000 miles. Worth bleeding the brakes to get new fluid in the entire system. I only use Honda specific fluids, except oil. Their coolant, brake fluid, transmission fluid and power steering are all superior in Honda's because the fluids are engineered specifically for Honda parts.
Great video but I'm having trouble putting the caliber back on but the pistons are not sliding back and forth like when you took the one part to the table
Great video , has all the looks and info needed to do this job right
Thanks. I hadn't seen the turning caliper before today. Had to improvise.
Use a hammer impact tool Thor’s screws come right out. And clean the rust off the ears of you cal bracket and caliper. With a wire brush
Thank you... headed out this morning to change mine.
Thank you so Much Matt
Now this is what i call a tutorial!
18:07 that was bad, you can hear the scraping noise.
What caused the noise?
@@youremakingmesomad The rotor rubbing against the dust cover.
Great and very helpful video!!! Thanks!!!
Yeah , good job. Well explained. Thanks
What lube you using mine don’t look that dark.
Great tutorial. Great video work too, most people have blurry or missed items. We'll done.
3/8 extension fits
Channel locks if you don’t have the kit
I accidentally took the spring off the back of my brake line. Anyone know a good way to get out back on?
The clips wont seat correctly unless you clean the caliper bracket, the rust kind of expands
I learn that myself too. Thought my breakpads where to big :)
You did not mention the torque requirement for bolts?
Good n tight
The German method = Good n tight ! Lol Actually the 17mm bracket bolts are 80 ft. lbs. and 12mm caliper bolts are 17 ft. lbs.
good job
Use stainless and it wont be rusting like that
YOU EVER HEARD OF A Impact SCREW DRIVER.
You mean an Impact Screwdriver ?
@@holdshortrunway27 yes
You forgot to put the screws back in the rotor.
Dont realy need them
@@regalakitas9498 Exactly. Do people think a screw that small and soft actually is important? Its just for the assembly line work so the rotors stay snug, and dont fall off during production