Turn the relay on and off using just one push button
HTML-код
- Опубликовано: 19 фев 2023
- Electronic Toggle Switch project can be used for switching On/Off application of home appliances like fan, light etc.
Latching a Relay very simple using one pushbutton
- - - - - - - - - - - -
⛔ Danger of electrocution in the relay part 🔥
⛔ خطر برق گرفتگی در قسمت رله 🔥
- - - - - - - - - - - -
⁘ ⁘ ⁘ ⁘ ⁘ ⁘ ⁘ ⁘ ⁘
🎵 Music 1
endless motion - Music by : www.bensound.com
- - - - - - - - - -
🎵 Music 2
perception - Music by : www.bensound.com
- - - - - - - - - -
🎵 And at the end of the video
Music : Epic Trailer - Magnetic Trailer [pixabay.com]
Audio File URL For Free Download:
pixabay.com/music/main-title-...
Good work
I can't thank you enough for this little project. It helped me complete fixing a bluetooth speaker. I used your circuit to make an On Off button. Very useful! Thank you again.
Good luck dear friend
Thank you for your positive opinion
I will make it too brother…thx ❤
I am satisfied with your work 👍 👍🔥
Thanks bro
نعم.
Does it use any current when the button is not pressed?
Does it keep latched if 12v is removed and re-applied?
When we turn off the lamp, the relay also turns off and does not consume any voltage or current. If it is disconnected and reconnected, the relay will remain off
The standby current when off will be 12mA
Your circuit is very good and useful. I want to replace the push switch to a touch plate. If I touch the touch plate the circuit will work or not.
Secondly Can I use 220v ac capicitor drop supply to make 12v dc to give to the circuit.
Thirdly can I use triac instead of relay. If yes than please show me the connection to fix the triac.
Anil Kumar Goel
I suggest you use another circuit
ruclips.net/video/vU3Ff4re6Ic/видео.html
If you don't like this circuit, I suggest you wait for future uploads
Jika menggunakan tegangan 24v, apakah hanya merubah relay menjadi 24v saja?
yes bro
Can i use 5 v relay and 5 volt supply?
Yes, you can, you just need to reduce the amount of 15 kOhm resistors
Tem como substituir o botão por um sensor incrível?
Esse projeto é bem legal
Yes bro
Já tentei colocar mas não consegui.
Onde ligar o infravermelho
Do you want to turn off and on the relay using an infrared remote control???@@naldomarantha9088
@@TECHIDEASCENTER Yes. I tried to connect the infrared receiver with the bd 140 in place of the button but of course it didn't work... in addition to the npn transistor, do I need another pnp? for red hell to work.... I'm not an aria professional but I like developing ideas
I'm watching from Russia.
Well done author! Respect!
Made simply and reliably!
But, there should always be a scheme! Preferably posted separately or in the video itself, at least for 4-5 seconds.
Then it will be considered a full-time job, and this is already professional and high-quality!
And you will want to watch something else on this channel!
.
And with regard to the circuit itself: the author, is it possible to make switching on the most common triac instead of a mechanical relay?
For example, the triac BTA41-600; BT136-600
Then it will be much better and more reliable.
////
Смотрю из России.
Автор молодец! Респект!
Сделано просто и надёжно!
Но, всегда должна быть схема! Желательно отдельно выложенная или в самом ролике, хотя бы на 4-5 секунд.
Тогда это будет считаться полной работой, а это уже профессионально и качественно!
И захочется ещё что-то смотреть на этом канале!
.
И касаемо самой схемы: автор, а можно ли вместо механического реле, сделать коммутацию на самом распространённом симисторе? Например симистор BTA41-600; BT136-600.
Тогда это будет намного лучше и надёжнее.
First of all, I am glad to meet you. I am from Iran
And regarding your question, I must say that yes, you can use a triac instead of a relay.
@@TECHIDEASCENTER
I am glad to welcome an Iranian, not a brit!!
About the scheme, so this is my good advice! After all, it is not difficult to give access to the Google cloud to each of your videos.
Well, now the most basic thing. The triac can be connected in two ways:
1. Directly
2. Through the optocoupler.
That's why I would like to know what current and voltage flow through the relay in order to choose the method of further connection.
Good luck with your work!
Sincerely from Russia!
\\\
Рад приветствовать Иранца, а не британца!!
По поводу схемы, так это мой добрый совет! Ведь совсем нетрудно давать доступ к Гугл-облаку к каждому своему ролику.
Ну а теперь самое основное. Симистор можно подключить двумя способами:
1. Напрямую
2. Через оптрон.
Вот поэтому, хотелось бы знать, какой ток и напряжение протекают через реле, чтобы выбрать способ дальнейшего подключения.
Удачи в работе!
С уважением из России!
Jak zrobić ten układ działający na 5v ? Z góry dziękuję.
You need to change the relay to 5V and also reduce the 15K resistors to about 10K.
@@TECHIDEASCENTER nie działa 🤷
Tylko 15 k zamienić na 10k ? Oba rezystory i nic więcej ?
Bo tak zrobiłem i nie podtrzymuję 🤷
@@mariuszryszka1116 yes
How dare you call negative ground
jika mengunakan relay 5v dan input 5v apakah harus merubah ukuran komponen. dan berapa ukurannya
Hello dear friend, you should change both 15k ohm resistors to 10k ohms and if it doesn't work, increase one of the 10k ohm resistors to 12k ohms.
@@TECHIDEASCENTER thanks bro
Promo sm 😉
😆
kalo mau buat tombol pushOn yang 2 mode bagiamana kak?
You can use both relay outputs
@@TECHIDEASCENTER skema nya kak? saya pemula tidak paham elektronik . saya belajar otodidak nonton diyoutube
bisa tolong di buatkan videonya kak?
@@kaylalbf4603 Coming Soon...
Terimakasih kakakk. Ditunggu videonya.
Tidak berfungsi brother..relay hanya bunyi cetek2.. resistor 15k dah coba ganti 10k..
It is possible that the relay is damaged, or that you have soldered a wrong part of the work. Please use new parts, there is a possibility of failure in used parts
Tipe transistornya apa
2N2222 NPN Transistor
Is there a way to make the circuit start to turn off?...when I energize it it starts with the relay activated and I would like to avoid that.
thanks!
Dear friend, every time you press the push switch, the relay will turn on and off. This circuit is not just for turning on or just for turning off. It does both.
@@TECHIDEASCENTER I understand what you are saying, but my question is: if I can make the circuit start off and not on? because when I give it voltage it starts on thanks
@@MrLucianoricco But when I connect the voltage, the circuit doesn't turn on so I don't switch myself. This can be seen in the circuit test at the end of the video.
I have a video to upload tomorrow that is similar to this circuit but with IC555, watch that video, it might interest you.