When cleaning your trottle body with a trottle body cleaner (solvent or spray) always remove the trottle body. Do not allow the solvent to get inside the intake of you engine because it can foul your spark plug causing your engine not to start and creating additional problems.
Thanks alot dear friend .....u being very helpfull in finding and cleaning mass airflow sensor of my car as i was unable to do so till date. Love from pakistan....
📌 Very Important.. 1. If throttle body barrel is not fully cleaned, 2. If engine has some extra blow by gases, 3. If the spark plug gap is excessive, (more than 1.1 mm) This vibration will not go off fully like in this video.. After completing all this procedure, turn off ignition switch, remove 2 fuses from engine fuse box, 1. ECTS 2. EFI main For 60 seconds and fix them again.. Now start the engine and see the results.. 📍This engine has (MAP) Manifold Absolute Pressure sensor, that is not Mass Air Flow (MAF sensor)
You seem to be knowledgeable. Is there supposed to be oil on the MAP sensor? I have an oil depletion issue (which I think is) resulting from the oil coming out of a breathing hole at the top that passes the MAP sensor.
If you are cleaning the throttle body and you have either a button or key start it really does not matter. What matters is that you remove the throttle body before cleaning. If however you are unsure about what you are doing, it would be best to allow your mechanic to do this for you.
My Vitz 2013 having same problem of vibration while slowing or stopping the Car, by switching on the hazard light. this is reduced while is switch on AC. I did this complete procedure of cleaning but problem still there.
Unlike 4 cylinder engines, 3 cylinder engines are not well balanced. Basically because of them having only 3 cylinders. The reason why a little vibration is normal. The main part that goes bad and increases vibration is the ' Hydro engine support' on the vehicle. It's the one on the left when opening the hood. In the video, your idle is going down and below 700 rpm as the engine is getting to its operating temperature, the cause of vibration. 1krfe 1.0 should be around 750 rpm.
I have a 2010 Toyota Passo which is three cylinder's how do I stop the vibrations . It vibrates at idle stop and whenever AC is on at a idle stop or when put in reverse?
@@grimmyboss2079change your engine mounts, mainly the hydraulic one. Have the throttle body cleaned. Change your spark plugs to Iridium ones. I did all of the above and 95 percent of the vibration is gone. If it persists, check the ignition coils and the belt for slippage.
Usually when you switch to heating the cabin of your vehicle by turning the knob from cool to heating you automatically close the cooling vents and open the heating vents in the dashboard. If when you you have a knob to switch this function you should hear a thinking sound when being switch from cooling to heating. First check this function before doing anything else.
I personally faced the same problem with my vitz 2007. I resolved the problem. How ? There is a small "LK screw also called allen screw" on throttle body covered with some kind of sealent/silicon type material. Remove that silicon and tight (clockwise) with Allen Screw driver.(Perform this while engine is switched off). Start the engine and check if problem still exists repeat the action. i resolve it with 2.5 full clock wise rotation.
@@ShelDockToyotaVitz its tiny screw. All second generation vitz (2005 to 2010)have this screw. Might be third gen did not have this screw. Its on your front while standing in front of car. Its located below plastic portion/part of throttle. Normally its found below the electrice wires of throttle
hi when you clean the maf sensor does the vibration gone? because i have my yaris it has a engine vibration i am planing to clean the maf sensor does it helps to stop the vibrate if i clean the maf sensor?hi forgot onething did you disconnect the negative connection on the battery before starting to clean the throttle body and the maf sensor?
If the MAF sensor needs cleaning it can cause engine vibration. Cleaning the sensor will stop the vibration. Remember though that several problem can contribute to engine vibration.
You can as long as it is sprayed on and not wiped. You should not pour it on either. It should be left to properly dry before reconnecting. Also you need to ensure the gasoline is clean.
It hasn’t been reduced, the car was cold. It will be the same if the engine is hot. I have vitz 2013 and it has the same problem. I cleaned the throttle body, cat and spark plugs, nothing changed. Now going for the fuel injectors and fuel pump, lets see what happens.
For my 2011 vitz it has helped because the vibration is not as bad as it was. Even now driving for long distances it still is good enough. Hopefully you can find a solution for your issue.
@@TheAndyplaylist i had this vibration for three years i have vitz 2012 ksp130 i clean throttle body every week and map sensor nothing help all parts air cleaner original i week ago i decided to clean the EGR its under the air box on the right side i had to remove the inlet ,now i clean it very well and from now the engine no vibration at all i reset it and now no little vibration . this is the solution for these 3 cyl cars TRUST ME good luck
Are you sure the vibration is gon... Not possible in this engine..... Now maybe okay but after you drive your car make a new video.... I think the vibration comeback again...
I have been driving my car for about a month now since I cleaned the throttle body and valve. Vibration is about 5%, not fully gone but significantly reduced.
@@bilalrafique1668 If your idle rpm is a bit too much then dirt somewhere on either the throttle body cylinder or the valve is preventing it from closing properly. Sometimes when cleaning, dirt may be pushed or lodge in areas preventing proper closing of the valve. Ensure all areas around the cylinder and valve is properly cleaned. There is a rubber gasket under the throttle body. If not seated properly then air may escape under it causing higher than usual idle rpm.
When cleaning your trottle body with a trottle body cleaner (solvent or spray) always remove the trottle body. Do not allow the solvent to get inside the intake of you engine because it can foul your spark plug causing your engine not to start and creating additional problems.
Having some faults with codes
Good job brother one love from Ghana 🇬🇭
Thanks alot dear friend .....u being very helpfull in finding and cleaning mass airflow sensor of my car as i was unable to do so till date. Love from pakistan....
Good to know that you solved your engine vibration problem.
Just a note that is a MAP Manifold Absolute Pressure Sensor not a MAF Sensor
This cleaning of MAF sensor removed ratling of vitz at idle....Thanks alot
Also the trottle body cleaning helps.
Please tell me what is this
📌 Very Important..
1. If throttle body barrel is not fully cleaned,
2. If engine has some extra blow by gases,
3. If the spark plug gap is excessive, (more than 1.1 mm)
This vibration will not go off fully like in this video..
After completing all this procedure, turn off ignition switch, remove 2 fuses from engine fuse box,
1. ECTS
2. EFI main
For 60 seconds and fix them again..
Now start the engine and see the results..
📍This engine has (MAP) Manifold Absolute Pressure sensor, that is not Mass Air Flow (MAF sensor)
You seem to be knowledgeable. Is there supposed to be oil on the MAP sensor? I have an oil depletion issue (which I think is) resulting from the oil coming out of a breathing hole at the top that passes the MAP sensor.
Same@@EvonGray
Yes brother ,this is what we want ,a demonstrating videoq
Thanks for your video it helped a lot
Thanks you appreciate it
Thanks a lot bro this video helps me a lot today with my 2013 Toyota Vitz..✊🏿✊🏿✊🏿💯💯💯😊😊😊
Many thanks for your patience sir
Does cleaning Airflow Sensor improve fuel consumption? My current consumption has been So bad, instead of 24KM per litre, it's like 12KM per litre
@@eliaschela4279 yes cleaning your air flow sensor improves fuel economy.
Thank you very much Mr Sheldock for your brilliant advice on this particular Toyota Vitz
You are welcome my friend.
Where are you located having a problem with my 2006 toyota vitz want you to give it a check sir I'm in spanish town
I have a button start vitz where cleaning the throttle body and removing the sensor should I disconnect the battery or it's best to check my mechanic
If you are cleaning the throttle body and you have either a button or key start it really does not matter.
What matters is that you remove the throttle body before cleaning. If however you are unsure about what you are doing, it would be best to allow your mechanic to do this for you.
Ashiq Khan Swabi auto workshop thakra mansehra ya Mira RUclips channel ha
My Vitz 2013 having same problem of vibration while slowing or stopping the Car, by switching on the hazard light. this is reduced while is switch on AC. I did this complete procedure of cleaning but problem still there.
igual en mi vitz
I have same problem in my vitz,, Is your problem solved?
Same here..
Unlike 4 cylinder engines, 3 cylinder engines are not well balanced. Basically because of them having only 3 cylinders.
The reason why a little vibration is normal.
The main part that goes bad and increases vibration is the ' Hydro engine support' on the vehicle.
It's the one on the left when opening the hood.
In the video, your idle is going down and below 700 rpm as the engine is getting to its operating temperature, the cause of vibration.
1krfe 1.0 should be around 750 rpm.
I have a 2010 Toyota Passo which is three cylinder's how do I stop the vibrations . It vibrates at idle stop and whenever AC is on at a idle stop or when put in reverse?
@@grimmyboss2079change your engine mounts, mainly the hydraulic one. Have the throttle body cleaned.
Change your spark plugs to Iridium ones.
I did all of the above and 95 percent of the vibration is gone.
If it persists, check the ignition coils and the belt for slippage.
@@1artonpower thank you very much will do that and get back to you
Good
Mr sheldock how tell if your water pump is not pumping properly my heater is not heating no leaking notice 2006 vitz reply please sir.
Usually when you switch to heating the cabin of your vehicle by turning the knob from cool to heating you automatically close the cooling vents and open the heating vents in the dashboard. If when you you have a knob to switch this function you should hear a thinking sound when being switch from cooling to heating.
First check this function before doing anything else.
A thumping sound
I personally faced the same problem with my vitz 2007. I resolved the problem. How ? There is a small "LK screw also called allen screw" on throttle body covered with some kind of sealent/silicon type material. Remove that silicon and tight (clockwise) with Allen Screw driver.(Perform this while engine is switched off). Start the engine and check if problem still exists repeat the action. i resolve it with 2.5 full clock wise rotation.
This trottle body does not carry this screw.
@@ShelDockToyotaVitz its tiny screw. All second generation vitz (2005 to 2010)have this screw. Might be third gen did not have this screw. Its on your front while standing in front of car. Its located below plastic portion/part of throttle. Normally its found below the electrice wires of throttle
My toyota vitz is 2011
Can u share picture of that
@@nsaleem86 share your email for picture. No option here for pasting / uploading picture please
Can carb cleaner be used to clean the mass Airflow sensor?
Its best you use a cleaner specifically for the Mass Airflow Sensor. Resedue left on the sensor because of an incorrect cleaner can damage the sensor.
Okay noted. Thanks.
Did you pull a code for the mas?
The engine check light was not in the on position.
hi when you clean the maf sensor does the vibration gone? because i have my yaris it has a engine vibration i am planing to clean the maf sensor does it helps to stop the vibrate if i clean the maf sensor?hi forgot onething did you disconnect the negative connection on the battery before starting to clean the throttle body and the maf sensor?
If the MAF sensor needs cleaning it can cause engine vibration. Cleaning the sensor will stop the vibration. Remember though that several problem can contribute to engine vibration.
Can I use gasoline to clean MAF sensor?
You can as long as it is sprayed on and not wiped. You should not pour it on either. It should be left to properly dry before reconnecting. Also you need to ensure the gasoline is clean.
My vitz is only.giving 8 9 average locally plz advice what i do
It hasn’t been reduced, the car was cold. It will be the same if the engine is hot. I have vitz 2013 and it has the same problem. I cleaned the throttle body, cat and spark plugs, nothing changed. Now going for the fuel injectors and fuel pump, lets see what happens.
For my 2011 vitz it has helped because the vibration is not as bad as it was. Even now driving for long distances it still is good enough.
Hopefully you can find a solution for your issue.
Any luck with vibration fix? Because i have 2012 and having rough idling problem
Vibration is greatly reduced but not completely gone. Am still working on a solution.
I cleaned the fuel injectors and fuel pump, the vibration is reduced but not completely gone.
@@TheAndyplaylist i had this vibration for three years i have vitz 2012 ksp130 i clean throttle body every week and map sensor nothing help all parts air cleaner original i week ago i decided to clean the EGR its under the air box on the right side i had to remove the inlet ,now i clean it very well and from now the engine no vibration at all
i reset it and now no little vibration . this is the solution for these 3 cyl cars TRUST ME good luck
Can the brake/carburetor cleaner be used?
Yes it can be used to help clean the trottle body. You also need to use a rough cloth to scrub away some of the particles because it can be stubborn.
Wonderful
Thank you! Cheers!
unfortunately , this isnt Mass Air Flow (MAF) sensor, this sensor is called MAP sensor
I know in my vehicle it uses a manifold absolute pressure sensor- MAP for short.
Check PVC valve, might be stuck open...
Thanks for your recommendation. I did check the PVC valve and it is in good working condition.
Vitz car after gear with ac engine vibrate when parking no vibration
When you switch the ac on you should hear the engine idle rpm increase. If this does not happen try idle code re-learn.
My dears is it posible some body send me clip that how to i some % solve vibration of vitz 2013 model really i am great full.with many many PRAYING.
What condition creates the vibration?
Are you sure the vibration is gon... Not possible in this engine..... Now maybe okay but after you drive your car make a new video.... I think the vibration comeback again...
Aamir Nawaz replace pvc value my car vibration comes to 1% only. Much much reduced
I have been driving my car for about a month now since I cleaned the throttle body and valve. Vibration is about 5%, not fully gone but significantly reduced.
@@ShelDockToyotaVitz i have tried this. vibration is gone but car is consuming more fuel. any advice?
@@bilalrafique1668 If your idle rpm is a bit too much then dirt somewhere on either the throttle body cylinder or the valve is preventing it from closing properly. Sometimes when cleaning, dirt may be pushed or lodge in areas preventing proper closing of the valve. Ensure all areas around the cylinder and valve is properly cleaned.
There is a rubber gasket under the throttle body. If not seated properly then air may escape under it causing higher than usual idle rpm.
@@bilalrafique1668 Increased idle rpm can result in more fuel consumption.
my car is not raving
This seems like a computer problem
its MAP not MAF
Can you share link of obd device and its app for Android
Bluedriver scan tool
www.amazon.com/BlueDriver-Bluetooth-Professional-iPhone-Android/dp/B00652G4TS/ref=mp_s_a_1_1_sspa?crid=22GPIP2CG601M&keywords=bluedriver+scan+tool&qid=1700867636&sprefix=bluedriver+scan%2Caps%2C185&sr=8-1-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9waG9uZV9zZWFyY2hfYXRm&psc=1
Go to play store then type BlueDriver OBD2 Scan Tool. The icon looks like the engine check light on your dash in the car.