Great video - thanks for uploading. I've made several dipoles in the past few months (2) 10m and a 40m. As my design improves I appreciate the center piece you featured here. I plan on adding this as my antennas evolve. Thank you - 73
Ps I use a beer can to wind a choke, at the terminator. Then use a wire tie to hold coil near and use a UV safe zip tie to relive the stress on pl259. Once again my liquid tape at the ready . To seal up the plug
Ah! I found half inch plexiglas. And cut it in to rectangles. Got so much it will last me the rest of my life time. So when I install my dipoles I set the wire then coat the joins with liquid tape. Dry? Pull her up and on the air. Tks Fer the show de kv4li
Thank you for the video. What size (inner diameter) PVC pipe did you use? Seems to be a very tight fit of the SO-239 into the bottom piece. Did you have to grind off the corners of the S-239 to get it to fit into the PVC end cap? 73
Gosh ... I don't know the diameter...I went to the hardware store and just found fittings that would work. Yes, you may need to grind off the corners to get the 239 to fit.
Yes you could make a dipole antenna and use it for CB radio. CB antennas are usually verticals though but you could try it and see how it works. This center insulator will work on any wire antenna where you are connecting coax for a feedline. Just make sure you cut your wires the right length.
How about a detailed list of the parts in the description needed to assemble this device? Screw sizes, nuts, washers, wire gauge, and PVC cap sizes, please...
I made one for a “horse fence” antenna seven years ago. Got the PVC and hardware at Home Depot. Already had the SO 239. I think cost was about $7.00, give or take a few cents. Was worth the time and effort. This is a good and helpful video.
WRONG WAY. NEVER USE STEEL PARTS. They are extremely lossy. Antenna connections must be SOLDERED not mechanically connected bc RF causes extreme oxidation and corrosion. .NEVER twist the antenna wires at the feedpoint, that does bad things to the fields.
Great video! I've been looking for a detailed video like this one.
Thank you. A lot of people helped me along the way. So, I try to do the same. Glad you liked the video
Great video - thanks for uploading. I've made several dipoles in the past few months (2) 10m and a 40m. As my design improves I appreciate the center piece you featured here. I plan on adding this as my antennas evolve. Thank you - 73
That's great. Enjoy! de N2RGT
Clear and to the point. I'll be giving this a try on my first antenna build later this month. Thanks for posting.
Great! Good luck. Thanks for the comment
Really good video. Thank you.
Great video! Thank you for posting! Looking forward to making a few of these for hunting camp! Your an inspiration to all new hams out there! 73's
Thank you. I like to share what I have learned about our great hobby. Good luck with your projects and enjoy that hunting camp!
Great video buddy! Thank you! I love making center conductors, those are so fun!
Sir, Nice video presentation. Thanks 👍.
Great simple video! Thank you!
Great video! Thank you very much for taking the time to video!! 73's
Profesional job sir.
Thanks.
Great video. I always used grey electrical boxes, that said, the price for those is out of sight now. This will work fine.
Yes. Everything is so expensive now. They are making life very difficult
I enjoyed your comments and ideas. Looks good.Kf5k 73
Thanks James.
Very good DIY video!! Thanks 73
Good video. Helpful indeed. Thank you.
Thanks for the video!
Thanks for the video.
metal base must go on outside, otherwise the screw thread is too short for pl259
Like the idea of using a screw to secure both pieces!! maybe use Anderson connectors to connect the wires? justathought
Ps I use a beer can to wind a choke, at the terminator. Then use a wire tie to hold coil near and use a UV safe zip tie to relive the stress on pl259. Once again my liquid tape at the ready . To seal up the plug
Fantastic video inspiring to see how feasible this can be. Thanks and 73! KO4KMA
Ah! I found half inch plexiglas. And cut it in to rectangles. Got so much it will last me the rest of my life time. So when I install my dipoles I set the wire then coat the joins with liquid tape. Dry? Pull her up and on the air. Tks Fer the show de kv4li
Can you provide the drill bit sizes that you did in this video? Thanks
great tutorial
Thanks!
Xclnt build,,,store boughts, are too pricey,,,this is an xclnt design, and will last 4ever,,,cool vid,,de NV1H😎
Hello Tim, Fantastic job, Have you used it any power on this antenna? I'm curious if it will handle the legal limit. Thank you
Nice building instructions THX 73 Do9Du
You are welcome. Take care & good DX! 73's
Awesome
I enjoyed the video you done a great job explaining how to make the center 1:1 . 73 AE4OY WILLIAM Peacock EM-81UF
Very helpful! This is my next project. Does the PVC housing (cap and receptacle) have a name?
I really don't know about a name. I just went to the store and started putting pieces together.
Great tutorial. But don't we need to use a balun too?
No, you don't need a balun. Just tune up and go!
Thank you for the video. What size (inner diameter) PVC pipe did you use? Seems to be a very tight fit of the SO-239 into the bottom piece. Did you have to grind off the corners of the S-239 to get it to fit into the PVC end cap? 73
Gosh ... I don't know the diameter...I went to the hardware store and just found fittings that would work. Yes, you may need to grind off the corners to get the 239 to fit.
@@TimTools99 Thank you 73
Great video.
However what is the plastic pot you used? it looks like some domestic plumbing, but I have never seen anything like that.
PVC fittings
@@TimTools99 Domestic plumbing PVC fittings?
Never seen anything in that kind of configuration.
Could I used this same dimension for a TRC-485 CB radio in my home, as a base station?
Yes you could make a dipole antenna and use it for CB radio. CB antennas are usually verticals though but you could try it and see how it works. This center insulator will work on any wire antenna where you are connecting coax for a feedline. Just make sure you cut your wires the right length.
How about a detailed list of the parts in the description needed to assemble this device? Screw sizes, nuts, washers, wire gauge, and PVC cap sizes, please...
gosh ... I just grab some stuff and screw it together. I don't have a list.
So how much do you think your project cost?
I made one for a “horse fence” antenna seven years ago. Got the PVC and hardware at Home Depot. Already had the SO 239. I think cost was about $7.00, give or take a few cents. Was worth the time and effort. This is a good and helpful video.
Great build but you sure did make things way more difficult on yourself than it needed to be.
WRONG WAY.
NEVER USE STEEL PARTS. They are extremely lossy. Antenna connections must be SOLDERED not mechanically connected bc RF causes extreme oxidation and corrosion.
.NEVER twist the antenna wires at the feedpoint, that does bad things to the fields.
Good information