Repair diode 1N4007 560k resistor will be 470k (this is not important, it is only responsible for discharging excess power) 02:50 Led 9v 03:40 Led 3v 04:26 Led 12v 05:00 Led 98v
Should connect 10ohm resistor in series to AC input to work as fuse in case of capacitor fails. This circuit should only be used in a concealed plastic environment.
Very very nice Like👌🏻👌🏻👌🏻👌🏻👌🏻 من سالها دنبال ی همچین مداری هستم برای چندین چراغ شارژی 60led و چراغ شارژی پیشانی 1led و این بهترین و آسانترین مدار و طرحی بود که شما یادم دادین مرسی mersy 👌🏻👌🏻👌🏻✌🏼🌹😊❤
The DC voltage rating of 820nF film capacitor used in circuit is 250 V DC. This value is not high enough, the voltage peak across this capacitor could be more than 250 V, it depends on load and on the value of mains. The correct type of capacitors should be a Class X2 capacitor with a 250 V AC or 275 V AC. A non Class X2 capacitor in case a failure could burn or explode. This circuit is very common on the web but often in web page and video not well understood. The circuit in the video is not true voltage supply, the current is limited mainly by the value of film capacitor. It would be very useful some formulas to size the value of the circuit components.
😮 ooohhh THANKS wonderfull maravilloso sistema de crear un circuito electrónico para poder utilizar estas luces led!! 🔥🤩🔥👍 Chévere vídeo 😁 gracias por compartirlo! Dios te bendiga y cuide mucho ah bueno 🙏
Extraordinary. You really understand the concept of electronics. Our understanding so far is that the voltage drop from the rectifier must use a transformer.
this circuit is not safe and use in cheap circuits.it not use galvanization.but it is not true about this circuit.for any ampee must use capacitor with differnt sizes .but it uses one capacitor for anythings.i think it is fake.
@@freedomisfood6966it is not fake. The circuit in this video is 100% legit. BTW, it is a capacitor dropper circuit and can be found in many cheap Chinese rechargeable torch, led bulb and fly swatter.
First of all, thank you for watching and giving your honest opinions. With this circuit, it actually applies a lot in circuits that do not need high power, such as controlling relays or simple power circuits. Although it is not safe, for a closed system with good insulation and insulation, it will also be safe. And although this circuit is not complete, but where those components are, we can easily find them and implement it. And the capacitor value will increase when we need high power, but with a capacity of over 1amp, this circuit will not meet the capacity we need. I Operated It. How to Make a #12v PC Fan running from #220v Grid. #diy @homediyelec ruclips.net/video/qOpH5CfztQM/видео.html
bai koto votlez e koto ampiar ta ki kore nirnoy korbo....et kanu mekani ekhane boltez bariye led kete repe r kora hoy ...bootez barie morgir framer lite fatano hoy......o jhor jhora kora hoy...rador lal ift helikapter motor dara 80 heke 104 puk dai....joypara esoppor bazar
Thank you for the easy explanation....I have a question, please....I am trying to run a 12-volt 1.2mAh battery drill on trans that converts from 220 to 12 volts AC and the current is unified into DC by a unification circuit with a capacitor.... but when The measurement of the voltage coming out of the unification circuit on the Avo reads 19.2 volts.... How can I lower the current to 12 volts (although I tried the drill and it worked normally, but I am afraid that it affects it).... Thanks alot
Hello. I wanted to ask for advice. Me Alternator Delco 12si it is Europ version for Opel Ascona C car. Me problem when ever I try to use hv ceramic capacitors they call that staff plasma ignition and it does work great with me engine. How ever I put multipel of them in series placed 1 side to the + terminal on me E core ignition coil and the 2 conection simply ground to baterry. Now the funny thing is me Alternator is back chargeing constantly under normal rpm the alternator light refuse to go off unless I go higher rpm with me engine around 3000-4000rpm +/-. So aperantly capacitor types have some effects on alternators lot Tractor alternators are equped with capacitors they are produced in China or India and I know if those capacitors go bade the tractor alternator wont charge baterry or if wrong rotatio direction alternator is buyed be acident as well it wont charge baterry. So now me question is how to determine alternator reaction be useing centrain capacitor types and resistors? In me case it changed the starting charge rpm value be useing hv ceramic capacitors. So please any one help me I love to use Amplifiers and Plasma ignition they are great for engines who run on low quality fuel. So please can some one explain to me or make video how to make seperate exition circuet for the field winding on delco 12si alternator if posibel it be manuali controled so the alternator can be switched on and off at any engine speed rotation. I also was wondering if current cut off selenoid culd be used to protect baterry from over charging. Me current voltage in me baterry is around 15.5 volts it goes higher with plasma ignition around 16-17 volts the baterry seams to be fine but no current unless I go higher rpm ranges with me engine. So please show me some one how does seperate circuet look like for those old alternators Im not shure if small 9 volt baterry culd run fiel coil from alternator and how much time it wuld work Im afraid to blow up some thing. So the engine mostly behaves if the bridge rectifier fail,diode trio failure,back current from dashboard or when the voltage regulator is damagen in those casses baterry over charge or under charges but be plasma ignition that does not acure unless you go low'r rpm ranges with the engine. So I do have cinde off problem there understanding how the delco voltage regulator works and how to control it . The voltage regulator has only 1 ic chip and 1-2 small capacitors nothing ells in that thing is present I belive the alternator is partialy controled via the positive linear voltage regulator and alternator bulb as well. They did made huge mistake by bypassing the diode from alternator light to the engine warning light Im not concerned about back charge for now only want to know how manualy control voltage regulator and prevent external capacitors to interact with alternator normal operation . If some one know solution please mesage me. Thanks .
Only used to light led lights, although not pulling at 100% led capacity, but ensuring led durability. It's safe when we cover it. And this circuit can't charge the battery sir
La resistencia que coloca en serie con el condensador no es de 560k sino de 470k según el código de colores para las resistencias. Así mismo la ultima resistencia tampoco es de 460 ohmios sino de 470 ohmios.
La resistencia que va en el primer capacitor y que mencionad como de 560k, no corresponde a los colores, 560k es verde, azul, amarillo, y en el video se aprecia como amarillo, negro o marron, amarillo, haber si lo puedes explicar por Favor.
Excellent video! I follow your channel and the videos are always amazing. I'm still in my infancy with electronics. If it were to feed with 127 AC, would it be enough to replace the ceramic capacitor? What would be recommended? Thanks! Thanks for sharing your knowledge!!!
Thank for the video. Well demonstrated. But could you please explain how 12V output is also glowing 3volt light strip without damage? Will be glad to get your reply.
@@HIFISOUNDS Couldn't understand your reply. Did I ask a stupid question? If you have answered this before somewhere and are fed up with repeating then please send the link.
When 3volt LED connected then capacitor knows its value 3 so it pass only required volt, same for other LED'S when you need more volt capacitor fullfil it.
Cristal, good afternoon, how is this a question in my country the Volt. is 120V, the components you use can be used for this voltage, I appreciate your support,
I need to create a two-phase power supply that can handle both 127V and 220V AC input. The objective is to transform either of the two voltages to 60V AC without using a transformer. How can I achieve this?
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
Repair
diode 1N4007
560k resistor will be 470k (this is not important, it is only responsible for discharging excess power)
02:50 Led 9v
03:40 Led 3v
04:26 Led 12v
05:00 Led 98v
What about the current ,, Amperage ?
220 V fan ?
Sir,pf 250v824j ke jagah aur kya kya pf use karskte hain
Kepisitar ki belyu us pe rajistenc ki belyu
sir agr me same banao to kaam karegah ya nahi batao plz
Лайк одназначно заслуженный за подробный обзор и проделанную работу. Успехов тебе и Здоровья.❤
This circuit is potentialy |>> LETHAL
Should connect 10ohm resistor in series to AC input to work as fuse in case of capacitor fails. This circuit should only be used in a concealed plastic environment.
Is this cicuit suitable to drive a dc motor in an enclosure?
Bro if I use a fuse or I put more than capacitor and I put resistor this will be ok ? Pls reply
Give us your solution
Very very nice
Like👌🏻👌🏻👌🏻👌🏻👌🏻
من سالها دنبال ی همچین مداری هستم برای چندین چراغ شارژی 60led و چراغ شارژی پیشانی 1led و این بهترین و آسانترین مدار و طرحی بود که شما یادم دادین مرسی mersy 👌🏻👌🏻👌🏻✌🏼🌹😊❤
The DC voltage rating of 820nF film capacitor used in circuit is 250 V DC.
This value is not high enough, the voltage peak across this capacitor could be more than 250 V, it depends on load and on the value of mains.
The correct type of capacitors should be a Class X2 capacitor with a 250 V AC or 275 V AC.
A non Class X2 capacitor in case a failure could burn or explode.
This circuit is very common on the web but often in web page and video not well understood.
The circuit in the video is not true voltage supply, the current is limited mainly by the value of film capacitor.
It would be very useful some formulas to size the value of the circuit components.
Safety
Wow, good and useful circuit making to select volts variant.gift💐💯🍀🌻🌻🌼🌼✌✌✌👍👍👍👍
😮 ooohhh THANKS wonderfull maravilloso sistema de crear un circuito electrónico para poder utilizar estas luces led!! 🔥🤩🔥👍 Chévere vídeo 😁 gracias por compartirlo! Dios te bendiga y cuide mucho ah bueno 🙏
Extraordinary. You really understand the concept of electronics.
Our understanding so far is that the voltage drop from the rectifier must use a transformer.
this circuit is not safe and use in cheap circuits.it not use galvanization.but it is not true about this circuit.for any ampee must use capacitor with differnt sizes .but it uses one capacitor for anythings.i think it is fake.
@@freedomisfood6966 have you try it ???
@@freedomisfood6966it is not fake.
The circuit in this video is 100% legit.
BTW, it is a capacitor dropper circuit and can be found in many cheap Chinese rechargeable torch, led bulb and fly swatter.
Its because of the bleeding resistor(bleeder) and the capacitor.
First of all, thank you for watching and giving your honest opinions. With this circuit, it actually applies a lot in circuits that do not need high power, such as controlling relays or simple power circuits. Although it is not safe, for a closed system with good insulation and insulation, it will also be safe. And although this circuit is not complete, but where those components are, we can easily find them and implement it. And the capacitor value will increase when we need high power, but with a capacity of over 1amp, this circuit will not meet the capacity we need. I Operated It.
How to Make a #12v PC Fan running from #220v Grid. #diy @homediyelec
ruclips.net/video/qOpH5CfztQM/видео.html
Charles Bradshaw is Right 100% the Circuit is Lethal if the Capacitor goes kaputt.
Nice send some more circuits like this in different configurations 👍
no... how long this unit working, u have no zener, it may damage led with in 10 minits
- How dangerous you want it to be?
- YES!!! 😱💥☠️
Creative video, like it,thanks for sharing:)
Ý tưởng tuyệt vời 👍👍👏🏳️🌈
Cảm ơn bạn đã xem video ủng hộ kênh.
Can you please send the circuit diagram!
Way too many RUclips videos show normal poly capacitors. You MUST use an X type capacitor for safety reasons.
bai koto votlez e koto ampiar ta ki kore nirnoy korbo....et kanu mekani ekhane boltez bariye led kete repe r kora hoy ...bootez barie morgir framer lite fatano hoy......o jhor jhora kora hoy...rador lal ift helikapter motor dara 80 heke 104 puk dai....joypara esoppor bazar
Good. Simple circuit.
Es 1 circuit py kitne jhalar run kr skte hai
Bhai 12 dc volt ki streep light toran work kare ga
Please tell me
Hay lắm em ơi anh thích lắm mình giao lưu qua lại nghe em
Cảm ơn anh đã xem video.
maltimeetar 9 volt ka chala sakte h
Output is dangerous to touch remains at 220v DC all the time with reduced current not recommended to be used.
Muito bom valeu amigo gostei
Is it not constantly shine? Is it always flashing? Thanx
Thank you for the easy explanation....I have a question, please....I am trying to run a 12-volt 1.2mAh battery drill on trans that converts from 220 to 12 volts AC and the current is unified into DC by a unification circuit with a capacitor.... but when The measurement of the voltage coming out of the unification circuit on the Avo reads 19.2 volts.... How can I lower the current to 12 volts (although I tried the drill and it worked normally, but I am afraid that it affects it).... Thanks alot
Use resistance to step down the voltage in the output
You can use a 7812 IC to get exact same 12v from 19.2
Its ok if showing 19v,no problem at all. If you lower the voltage by 7812,drill will stop working because drill need 4 to 5 amps current
It's fine as is. The rectified / filtered DC will draw down to the ~12V vicinity once it's loaded down whilst operating the tool.
Hello.
I wanted to ask for advice.
Me Alternator Delco 12si it is Europ version for Opel Ascona C car.
Me problem when ever I try to use hv ceramic capacitors they call that staff plasma ignition and it does work great with me engine.
How ever I put multipel of them in series placed 1 side to the + terminal on me E core ignition coil and the 2 conection simply ground to baterry.
Now the funny thing is me Alternator is back chargeing constantly under normal rpm the alternator light refuse to go off unless I go higher rpm with me engine around 3000-4000rpm +/-.
So aperantly capacitor types have some effects on alternators lot Tractor alternators are equped with capacitors they are produced in China or India and I know if those capacitors go bade the tractor alternator wont charge baterry or if wrong rotatio direction alternator is buyed be acident as well it wont charge baterry.
So now me question is how to determine alternator reaction be useing centrain capacitor types and resistors?
In me case it changed the starting charge rpm value be useing hv ceramic capacitors.
So please any one help me I love to use Amplifiers and Plasma ignition they are great for engines who run on low quality fuel.
So please can some one explain to me or make video how to make seperate exition circuet for the field winding on delco 12si alternator if posibel it be manuali controled so the alternator can be switched on and off at any engine speed rotation.
I also was wondering if current cut off selenoid culd be used to protect baterry from over charging.
Me current voltage in me baterry is around 15.5 volts it goes higher with plasma ignition around 16-17 volts the baterry seams to be fine but no current unless I go higher rpm ranges with me engine.
So please show me some one how does seperate circuet look like for those old alternators Im not shure if small 9 volt baterry culd run fiel coil from alternator and how much time it wuld work Im afraid to blow up some thing.
So the engine mostly behaves if the bridge rectifier fail,diode trio failure,back current from dashboard or when the voltage regulator is damagen in those casses baterry over charge or under charges but be plasma ignition that does not acure unless you go low'r rpm ranges with the engine.
So I do have cinde off problem there understanding how the delco voltage regulator works and how to control it .
The voltage regulator has only 1 ic chip and 1-2 small capacitors nothing ells in that thing is present I belive the alternator is partialy controled via the positive linear voltage regulator and alternator bulb as well.
They did made huge mistake by bypassing the diode from alternator light to the engine warning light Im not concerned about back charge for now only want to know how manualy control voltage regulator and prevent external capacitors to interact with alternator normal operation .
If some one know solution please mesage me.
Thanks .
How is it possible same ampere for 3v and 98v? There is no variability for different volt output?
Exactly. Looks like a variable input voltage to me.
In this vedio, 470K in polyester cross and another 470K in DC dropping across 3.3uf capacitor. Were is 560K ? (Green-Blue-Yellow)
Is it with work with one 3v led bulb
Can I use 754j 400v capacitor?
You can!
@@homediyelec ty!
@@homediyelec but can I use 22uf 400v capacitor?
This circuit is ok for low current load.
Tutorial ini untuk lampu jangka panjang aman ngga? Maaf saya orang indonesia. Mau nanya kalo untuk ngecas aki motor bisa ngga?
Only used to light led lights, although not pulling at 100% led capacity, but ensuring led durability. It's safe when we cover it. And this circuit can't charge the battery sir
Oh, warm tails. 👍🌹💡
Mạch điện phổ thông trong các đèn led hiện nay
La resistencia que coloca en serie con el condensador no es de 560k sino de 470k según el código de colores para las resistencias. Así mismo la ultima resistencia tampoco es de 460 ohmios sino de 470 ohmios.
La primera resistencia es de 470 k el violeta es 7
@@carlose081250 Si señor Violeta 7 - Verde 6 - Amarillo 4 - Azul 6.
Pl massure how much out dc volts.
Amazing l like it thank.
Thanks for the video
Aapne bataya o watt ke hisab se laga sakte he kya
Hello. I connect a 2W 460 ohm resistor to the output of the circuit and it gets hot. How many watts and how many ohms of resistors can be connected?
Please check
* The DC load current ( I© )
* Voltage across both terminals Current limiter 470E ( Vd )
* Apply this formula to find Wattage of 470E ( Wr)
* Wr = Vd x I©
For example: If Vd = 100V, and I© = 40mA
The power consumed by 470E = [100 x 40] mW = 4,000mW = 4Watts
*Take 20% higher rating for safety from overheating; ie 4.8W. Use nearest value available in market; ie 5W*
Please note: this kind of crude circuit is very unsafe for expensive load, also the line current limiter capacitor value and type used 824 / 250v is insufficient to drive above 5W load. _Never used this with Square wave inverter_
The current consumption is too high, this circuit only produces a few hundred mAh current.
Can we use smd bridge rectifier ?
Ok. Thank
@@homediyelec Thanks 🙏
what is the output power with no load? 220v?
the ceramic capasitor supply "automatically" the right voltage depending of the load respectevily?
Can it work for 6 watt led mcpcb
thank you for that sharing
Input 220 AC and output any combination DC volt? That true?
What you say is the truth
How can make emergence light with changing?
Plz replay me must.
Without the circuit diagram, the assembling process is useless for any electronic project. It is like to identify an elephant by blind people.
So nice thanks
Watching and sending support nice sharing
di pakai di dinamo bisa ta kak
Es bueno y práctico pero seria buena idea poner un caimán en cada polo para evitar soldar y desoldar cada módulo de LED a probar. Saludos!
Sir 1 watt ki led kaga sakte he kya
Led luxeon
Video is good, but pf 824J is not available, what may be its substitute ? Tripura.
Can I get circuit diagram of this project
Thank you for the sharing , you used 470kr and 470r but in video you said 560kr and 460r which one we should use and correct
oh sorry for this carelessness of mine, yes if possible you can also use the 560kr resistor. Thank you for watching the video
Try 560 kohm
Nice video bhai🙂🙂
SALUDOS. NUESTRA CORRIENTE ES DE 120 VOLT, COMO SERIA LOS ELEMENTOS, GRACIAS.
Nice ...,👍😀
क्या इस गेजेट से 48 वोल्ट डीसी पावर वाला सबमर्सिबल वाटर पम्प , 400 वाट, 10 एम्पीयर को चलाया जा सकता है -?
No
Which diod used in this ?
Volt gana vadivenne kohomada
Rasistance kitane watt ka lagaya hai
what is the diode that they use
how much watt 460 ohm resistor
Watching sir ricky ledtv doktors dull support
nice info, thanks!
La resistencia que va en el primer capacitor y que mencionad como de 560k, no corresponde a los colores, 560k es verde, azul, amarillo, y en el video se aprecia como amarillo, negro o marron, amarillo, haber si lo puedes explicar por Favor.
oh maybe it's just a thumbnail, it's for illustration purposes only
Thanks beautiful
24 watt amplifier me chalega
Ok
can this be used to operate high pressure sodium lamps and/or metal halide lamps?
No, usually those lamps require current in the order of one amp, yet the 470 ohm series resistor drops average current in the zone of half one amp.
Excellent video! I follow your channel and the videos are always amazing. I'm still in my infancy with electronics. If it were to feed with 127 AC, would it be enough to replace the ceramic capacitor? What would be recommended?
Thanks! Thanks for sharing your knowledge!!!
sorry my place will be 220v, and i haven't tried that yet, thanks for giving me more ideas
Olá bom dia
Poderia me dizer quais são os diodos que vc utilizou, será que posso utilizar um ponte retificadora pronta.
Obrigado
Ah sim,claro
what is out put current please?
Good, but you Can without the 1rst resistor 👍
👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍 good
What is the resistanc for ?
Good idea veray nice
Very Good.
And if you take 105j400v, will it work?
sirve para 110v AC+
...me tocaría hacer alguna modificación
If you want more capacity, please increase the candy capacitor index, but this circuit I made the current not up to 500amp
Brapa Amper ini bang
How much amoere on 24 volt dc
Transformer jese ampiyar कैसे niklenge
Thank for the video. Well demonstrated. But could you please explain how 12V output is also glowing 3volt light strip without damage? Will be glad to get your reply.
Same question
@@HIFISOUNDS Couldn't understand your reply. Did I ask a stupid question? If you have answered this before somewhere and are fed up with repeating then please send the link.
@@susantpal calm down...i just want to say, 'i have same question '
Same question
When 3volt LED connected then capacitor knows its value 3 so it pass only required volt, same for other LED'S when you need more volt capacitor fullfil it.
I'm going to end up building all of these.😁👍I'm in us will this work with 220 here? Thanks for any help.
Cristal, good afternoon, how is this a question in my country the Volt. is 120V, the components you use can be used for this voltage, I appreciate your support,
Yes, only 1 component need to change, capacitor 105,instead 584 and voltage of capacitor should be 250v or more
Is it possible to mount a 460R instead of a 470R??
need convert 110v DC to 12v DC, any video that con help me?
Thank for sharing
ถ้าใส่ไดโอดที่ทางเข้าledจะมีอายุยาวนาน มั๊ยครับท่าน
هل ممكن استبدل الليد بأى دائرة صوتية مثلا تعمل على 12 فولت ؟
No
How many max watt?
In this video observed you have used 2 nos 470k as per resistance colour code,am I right?
I need to create a two-phase power supply that can handle both 127V and 220V AC input. The objective is to transform either of the two voltages to 60V AC without using a transformer. How can I achieve this?
Terima kasih sangat bermanfaat, outputnya nyetrum gak bos🙏
Thanks for watching the video, yes the output is really shocking, but there are times when we need it in some cases.
@@homediyelec Thank you for responding to my question. Success is always for you.
bro is that auto volt ?
Thanks, for you.
Main pf capacitor not availableany alternative?
How many amps?