То есть вы не в курсе как работает обратная связь и шим контроллер, сделали из импульсного линейный, так проще было tl431 и несколько резисторов взять.
Ah, the good old 2N3055, the BJT king for power since the eighties. I would recommend modernize a little bit and use a Low Rds MOSFET instead. Les power loss, same current transfer.
Just buy a 10A buck converter, it is more efficient, the output voltage is regulated, and it is definitely easier to install without the need for modification
@@TARIQLAB thanks...I have made my own incubator that is heated by car single filament bulbs three on each side which are two separately controlled by their respective switches...I was using desktop computer power supply which of 250 Watts but it always trips...I found out that bulbs are drawing more power how ever each bulb is only 30 Watts I M only using three of them at a time other three are backup.
@@TARIQLAB Цель понятна, реализация слишком грубая. Вам будет полезно и интересно изучить принцыпы работы ШИМ преобразователей напряжения. Вы увидите как изящьно можно увеличить мощьность этого преобразователя не снижая КПД. А по доработке с видео, вся лишьняя мощьность будет тратиться на нагрев атмосферы, это не есть good...
То есть вы не в курсе как работает обратная связь и шим контроллер, сделали из импульсного линейный, так проще было tl431 и несколько резисторов взять.
Теперь куча энергии пойдёт в тепло... Нужно умощьнять ключь ключь в цепи трансформатора и сам трансформатор, КПД выше.
В чём смысл?
Awsome.
Thank you very much for the schematic.
very nice
I like with circuit diagram. 👍
Very good information 👌 brother
Thanks
Ah, the good old 2N3055, the BJT king for power since the eighties. I would recommend modernize a little bit and use a Low Rds MOSFET instead. Les power loss, same current transfer.
👍
Just buy a 10A buck converter, it is more efficient, the output voltage is regulated, and it is definitely easier to install without the need for modification
И где 10 А? На этой схеме и радиаторе и 3А получить не получится.
Режим импульсный не линейный , 3А точно есть а вот насчёт 10А уже сомнительно тут надо ставить полевик.
10А и не пахнет, тем более это быполярный транзистор а не полевой.
Tu de "mica" ai auzit ? Se pune intre tranzistor si radiator. Asa se lucreaza corect
oui, je sais que lorsque le dissipateur thermique n'est pas connecté à d'autres composants ou à l'alimentation, alors ce n'est pas nécessaire.
please 30 A
That's no upgrade, he's just using the buck convertor as a driver to a linear regulator.
This can work with a mosfet also correct?
Yes, Mosfet with low gate voltage like, IRFZ44N
How much is the load capacity... I mean can we run 12v lamps up to 100 w capacity
Yes, 2n3055 transistor max power output 115W
@@TARIQLAB thanks...I have made my own incubator that is heated by car single filament bulbs three on each side which are two separately controlled by their respective switches...I was using desktop computer power supply which of 250 Watts but it always trips...I found out that bulbs are drawing more power how ever each bulb is only 30 Watts I M only using three of them at a time other three are backup.
250w total out, that is for 12v, 5v, 3.3v . Maximum power is dedicated to 5v, 12v section may be less than 100w
Ну и зачем эти заморочки, плата и так напряжение регулирует.
чтобы увеличить амперы
@@TARIQLAB
Цель понятна, реализация слишком грубая.
Вам будет полезно и интересно изучить принцыпы работы ШИМ преобразователей напряжения.
Вы увидите как изящьно можно увеличить мощьность этого преобразователя не снижая КПД.
А по доработке с видео, вся лишьняя мощьность будет тратиться на нагрев атмосферы, это не есть good...