Thanks for making this!!! Its really easy and clear for begginers (like me)!!! i was tired of taking off the atmega from the board, and this really helps a lot!!!!! Great explanation!
As few folks have pointed out already, that last step is incorrect. When you upload the Blink program you need to press "Shift" key so that the IDE "Uploads as Programmer". Otherwise you'll just end up just programming the master Arduino with the Blink program and wiping our the ArduinoISP sketch in the master. Rest of the steps seems to be correct and the shown circuit worked for me.
Last step press "shift" and the click upload to give the program to the slave chip. And you need to see the led blinking when the chip is supplied externaly without isp pins.
I think ur last step(uploading the blink sketch is wrong) if u hold the "Shift-key" and then click on the "Upload button" then the sketch will be transferred 2 the IC on the breadboard, Otherwise only th UNO will be programmed
avrdude: Expected signature for ATmega328P is 1E 95 0F Double check chip, or use -F to override this check. Error while burning bootloader. how to solve sir
Mình muốn nạp code cho chíp atmega 328p để làm đồng hồ, muốn nạp code vào chíp atmega 328p bằng mạch adruino r3 thì làm thế nào? Bạn hướng dẫn được không?
sir issme basic code toh uplode hoo jate hai atmega 328 ic mae par jab mai ir code aur bakki code uplode karta hoon na toh jo yeh appna arduino ka ide software hai vo inn codes par katha hai error compiling for bord atmega328... abb iska solution bata doo please...
Thank you for creating this video as it has been a help in my continuing understanding of Arduino Uno and Bootloading ATMega's. I do have a question... Why did you connect the 10K Resistor between Pin1 of the Mega and 5 Vdc rail? Thank you for help with this question.
Kindly change the title of the video. The chip you use is Atmega328p which has different signature as compared to Atmega328. Your procedure is fine for Atmega328p but does not work with Atmega328. Also a video about Atmega328 will be appreciated.
Could you please.. make a vid on how to make the 328 minimal circuit thing (with the internal 8MHz oscillator) and how to program it?. cause thats what i will be needing in the near future
Sorry, you have a error, In the last part, you upload the "blink sketch" to the arduino , not to the atmega. you don't check if the atmega have a working bootloader.
true. the blinking is because of the sketch uploaded into main programming board. when atmega on breadboard is powered without arduino, led dosent blink nor any sketch gets uploaded.
This method is not proper bootloader,u don't check bootloader ic.blink pgm work only in audino.led blink can show aurdino 13 pin directly connect to separate led.please check
You are wrong! Your method provides to upload the program to Arduino, only. Your Atmega cannot be programmed or burned what you say. Please, replace this video with the correct one or delete.
Thanks for making this!!! Its really easy and clear for begginers (like me)!!! i was tired of taking off the atmega from the board, and this really helps a lot!!!!! Great explanation!
As few folks have pointed out already, that last step is incorrect. When you upload the Blink program you need to press "Shift" key so that the IDE "Uploads as Programmer". Otherwise you'll just end up just programming the master Arduino with the Blink program and wiping our the ArduinoISP sketch in the master. Rest of the steps seems to be correct and the shown circuit worked for me.
Thanks for the correction.Errata Mentioned in the Description
Last step press "shift" and the click upload to give the program to the slave chip. And you need to see the led blinking when the chip is supplied externaly without isp pins.
Really thanks sir with great difficulty I found a Indian teacher really thanks you sir my ears were tired by listening to aliens
oh, where did you learn from aliens .....
@@fastfourier3 from foreigners there english is very fast
Very clear and concise information. Keep it up.
Keep up your clear & excellent presentations - I like your paper pinout sketch as it assists clarity.
Thank you for your kind appreciation.
Saravanan AL done every thing as shown but still boorlode fail
Try taking out the spi connectors after you upload the blink sketch. No boot loader or blink uploaded.
I think ur last step(uploading the blink sketch is wrong) if u hold the "Shift-key" and then click on the "Upload button" then the sketch will be transferred 2 the IC on the breadboard, Otherwise only th UNO will be programmed
avrdude: Expected signature for ATmega328P is 1E 95 0F
Double check chip, or use -F to override this check.
Error while burning bootloader.
how to solve sir
Mình muốn nạp code cho chíp atmega 328p để làm đồng hồ, muốn nạp code vào chíp atmega 328p bằng mạch adruino r3 thì làm thế nào? Bạn hướng dẫn được không?
sir issme basic code toh uplode hoo jate hai atmega 328 ic mae par jab mai ir code aur bakki code uplode karta hoon na toh jo yeh appna arduino ka ide software hai vo inn codes par katha hai error compiling for bord atmega328... abb iska solution bata doo please...
Thank you for creating this video as it has been a help in my continuing understanding of Arduino Uno and Bootloading ATMega's. I do have a question... Why did you connect the 10K Resistor between Pin1 of the Mega and 5 Vdc rail? Thank you for help with this question.
Sir shall you share the video in Tamil it's useful to all other Tamil known people please considered this sir
please explain how to bootload 328p using ftdi (without the help of arduino board)
can Atmega 328 U is same function as Atmega 328 PU
Kindly change the title of the video. The chip you use is Atmega328p which has different signature as compared to Atmega328. Your procedure is fine for Atmega328p but does not work with Atmega328. Also a video about Atmega328 will be appreciated.
Could you please.. make a vid on how to make the 328 minimal circuit thing (with the internal 8MHz oscillator) and how to program it?. cause thats what i will be needing in the near future
SIR, FOR ATMEGA 8 IS SAME???
It works on atmega328 u?
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
HELP!!!!!!!!!!!!!!!!!!!!!!!
Hi sir what is shift key
Nice " presentation !
sir please guide how to read 485 data from energy meter using arduino
avrdude stk500_getsync() not in sync resp=0x00 error
Sorry, you have a error, In the last part, you upload the "blink sketch" to the arduino , not to the atmega.
you don't check if the atmega have a working bootloader.
true. the blinking is because of the sketch uploaded into main programming board. when atmega on breadboard is powered without arduino, led dosent blink nor any sketch gets uploaded.
Electromania
Don't worry, but the way, the bootloader write correct and only need connect through serial port to atmega and all work fine
i tried to connect serial communication too, it dosent work.
nice❤
This method is not proper bootloader,u don't check bootloader ic.blink pgm work only in audino.led blink can show aurdino 13 pin directly connect to separate led.please check
it only pograms your arduino and not the Atmega on breadboard. : (
How to programs it
You are wrong! Your method provides to upload the program to Arduino, only. Your Atmega cannot be programmed or burned what you say. Please, replace this video with the correct one or delete.
4:50 I think you missed the shift key Sir...
Thanks for the info.Mentioned in the description.
can i use 3.3 volt ?