awesome!! I have matching error hardware on kinetx 350 replaced, tried to upgrade the drive version, but the changes are no made them on studio 5000, any idea what's wrong and the circos are still showing drive error....thank you!!
It's fast because I made a very detailed version earlier last year and someone talked smack about it not being 10 minutes. So I made it a point to prove it could be done in that time limit. If you need a slower learning resource, use the search tab on this channel and type in the keyword "Servo" It will pull up all my servo videos. Also help you save time on learning to easily find what you need
Hi Shane You are the best, and I like coming back to your RUclips channel for help sometimes you are a bit fast for me but always good information. You have help me in the past so I'm back. Okay I just lost a Kinetix 6000 2094- BM-02 15A at 3am 😢 What I have in stock 2094-BM-01 6A. How do I configure this.? Can will this work? Thanks for your help. The Engineering department will be here in the morning 8:00 and they will fix it, but will not say anything to us night time electrician so you are my knowledge base. Thanks for your help always. Darren
To do that change, all you need to do is to be offline then change the model type then re-connect the module to the Axis it was connected to before. Very simple. Also, limit the torque so it does run over it's rating
Hello, I have a question. I have seen in the company where I work that different models of Allen Bradley PLCs are installed in machines. For example, there is a machine that uses a Micrologic 1400 to control 2 servo drives Oriental Motors. In this case the PLC uses an analog signal to control the speed of the servo motor. But the PLC that you use in this video don-t use analog signal to control speed and many other parameters. You control the servo motor with instructions like MAH, MAM, MAS, etc. I want to make my own servo training kit, but I am not sure if a MicroLogix 1400 would let me control a servo motor a you do with all these instructions. I appreciate all comments.
MicroLogix uses a different software version, it uses RSLogix 500 not RSLogix 5000 or Studio 5000. With that being said, the MicroLogix processor is not tag based so it requires output signals such as analog module. RSlogix 5000 & Studio 5000 which I teach in this video is a tag based system which is a much greater software than RSlogix 500. RSLogix 5000 & Studio 5000 use communication cards for servo controls. So with you asking about this, the MicroLogix processor is a less useful type than an RSLogix 5000 or Studio 5000 type. Hope that better helps explain
Sir I am using servo but when I am increasing frequency that time changes in stopped location I want stop same location each time which parameter I need to set
Hello, I have a Kinetix 6000 set and I want to use it with an interface that sends pulses and direction. I'm trying with an HSC high speed input module but I can't get the right program. Is it possible to do this? thank you
I am testing by entering pulses from an incremental encoder and the programming objective would be for the servo to go to the absolute position (counter value) as the encoder moves. It would be something like a loop where an absolute MAM instruction positions the servo to the counter value
@@fernandomatiasn so use an encoder to control the speed or position of the servo correct? I have a RUclips video on that if you want to use the search tab about servo controls
I would like to learn more about configuring an index position on a k300 drive. In our application, we can edit the index through the motion configuration software, but we are communicating with ethernet, and sending commands to move to position X or whatever. what I would like to do is change what that position is on a screen for alignment reasons in say a linear servo situation. I am searching for info, but it's not easy to find....
Hey Shane, I have a kinetix 6000, but it seems that It's not working. I try to turn on wiht 220 monophasic and 220 tripahsic power supply. What should I do?
Sounds like a regeneration of power from the mechanical set-up. Stopping to quickly or any type of regeneration of power. Most of the time, we add a braking resistance bank or chopping module
Thank you very much Mr.Shane, Adding to this there is an abnormal behaviour in rotation of the motor, The rotational speed gets increases automatically( more than set speed) Can we do anything apart from braking resistance bank.
Hey,, I can't even communicate to an AB ultra 3000. It was installled before I started this job and I can't get it to connect to my PC to set parameters. I'm using a USB to rs232 I made a cable using pin out, 2,3,5. Please any help is appriciated.
@@freaky_jsn_killr1364 Yes, USB to serial cable...set the port used for the USB to serial baud rate to match as well. Use device manager to verify port. Use that port for the RSLinx driver as well
You are a legend Shane, I haven't worked already with allen branley but with other manufacturers, in the way you are teaching I am learning a lot, thank you, and keep sharing your knowledge it is very important for us!
Sorry, I was slightly annoyed at the time so I was trying to prove a point. By doing things as required plus talking about them as I did them but very quickly because someone talked smack in one of my previous videos not actually being 10 minutes to move. I talked about the high points to keep this video short. If you want more detail then search this channel using the search tab the type in the keyword you want to view. It's simple and easy
@@caleb7799 Take average ? Don't you mean take advantage? I put a lot of effort into helping people & answering questions, especially on RUclips so if someone doesn't like the way I teach, please note that RUclips is full of people that teach PLC logic. Not near as in-depth however . Also, feel free to miss out on all of the future videos I am releasing in 2023 about servos. Not sure why people are heavy critics these days, it's a free video...i wish I had a place to turn to when I learned plc controls. Seriously, there was no RUclips 20 years ago, much less an easy way to search for answers. I think we should all be a little but more appreciative of anyone in the industry trying to help teach others. Whether we agree with them or not, we should at least appreciate their efforts.
*Visit our training center for more:*
allen-bradley-plc-training.teachable.com/
Hello, can I add kineix 350 In RSlogix5000 v20.04.00 ? I have added the EDS file but I can't see it on the list, could you help me please?
As a generic module
do more troubleshoting 3 phase motors and plc
What are you asking?
awesome!!
I have matching error hardware on kinetx 350 replaced, tried to upgrade the drive version, but the changes are no made them on studio 5000, any idea what's wrong and the circos are still showing drive error....thank you!!
This felt like a speed run video.. Didn't relay learn much here
It's fast because I made a very detailed version earlier last year and someone talked smack about it not being 10 minutes.
So I made it a point to prove it could be done in that time limit.
If you need a slower learning resource, use the search tab on this channel and type in the keyword "Servo"
It will pull up all my servo videos.
Also help you save time on learning to easily find what you need
Hi Shane
You are the best, and I like coming back to your RUclips channel for help sometimes you are a bit fast for me but always good information.
You have help me in the past so I'm back.
Okay I just lost a Kinetix 6000 2094- BM-02 15A at 3am 😢
What I have in stock 2094-BM-01 6A.
How do I configure this.?
Can will this work?
Thanks for your help.
The Engineering department will be here in the morning 8:00 and they will fix it, but will not say anything to us night time electrician so you are my knowledge base.
Thanks for your help always.
Darren
To do that change, all you need to do is to be offline then change the model type then re-connect the module to the Axis it was connected to before.
Very simple.
Also, limit the torque so it does run over it's rating
I get to tune couple unwind stand motors tomorrow and figured I could use the rundown, thanks for this.
Hello,
I have a question. I have seen in the company where I work that different models of Allen Bradley PLCs are installed in machines. For example, there is a machine that uses a Micrologic 1400 to control 2 servo drives Oriental Motors. In this case the PLC uses an analog signal to control the speed of the servo motor. But the PLC that you use in this video don-t use analog signal to control speed and many other parameters. You control the servo motor with instructions like MAH, MAM, MAS, etc. I want to make my own servo training kit, but I am not sure if a MicroLogix 1400 would let me control a servo motor a you do with all these instructions.
I appreciate all comments.
MicroLogix uses a different software version, it uses RSLogix 500 not RSLogix 5000 or Studio 5000.
With that being said, the MicroLogix processor is not tag based so it requires output signals such as analog module.
RSlogix 5000 & Studio 5000 which I teach in this video is a tag based system which is a much greater software than RSlogix 500.
RSLogix 5000 & Studio 5000 use communication cards for servo controls.
So with you asking about this, the MicroLogix processor is a less useful type than an RSLogix 5000 or Studio 5000 type.
Hope that better helps explain
Sir
I am using servo but when I am increasing frequency that time changes in stopped location I want stop same location each time which parameter I need to set
Please better explain what you are asking so I can help
Hello, I have a Kinetix 6000 set and I want to use it with an interface that sends pulses and direction. I'm trying with an HSC high speed input module but I can't get the right program. Is it possible to do this? thank you
If you have a Kinetix 6000 then why are you using a high speed counter card?
Are you adding an encoder or something?
@@ShaneWelcher I have an interface that controls servos by pulse and direction. I want to adapt the Kinetix 6000 for that application
I am testing by entering pulses from an incremental encoder and the programming objective would be for the servo to go to the absolute position (counter value) as the encoder moves. It would be something like a loop where an absolute MAM instruction positions the servo to the counter value
@@fernandomatiasn so use an encoder to control the speed or position of the servo correct?
I have a RUclips video on that if you want to use the search tab about servo controls
@@ShaneWelcher I need to control position
I would like to learn more about configuring an index position on a k300 drive. In our application, we can edit the index through the motion configuration software, but we are communicating with ethernet, and sending commands to move to position X or whatever. what I would like to do is change what that position is on a screen for alignment reasons in say a linear servo situation. I am searching for info, but it's not easy to find....
Yeah, not to many people use the K300.
I have a few of them, maybe I can do some videos on them when time allows
Hey Shane, I have a kinetix 6000, but it seems that It's not working. I try to turn on wiht 220 monophasic and 220 tripahsic power supply. What should I do?
If the standard control voltage is present & the LEDs or fiber is not working then the board might be bad
@@ShaneWelcher thank you so much
Great job Shane, the best courses I've ever taken on Udemy are yours. I'm still waiting for the Servo Mastery 2
Thank you for the kind words
Hi,
Facing frequently error E-10 and E-75 in my kinetix 6000 system.
How to eliminate this?
Sounds like a regeneration of power from the mechanical set-up.
Stopping to quickly or any type of regeneration of power.
Most of the time, we add a braking resistance bank or chopping module
Thank you very much Mr.Shane,
Adding to this there is an abnormal behaviour in rotation of the motor, The rotational speed gets increases automatically( more than set speed)
Can we do anything apart from braking resistance bank.
@@grakeshrao2319 depends on the mechanics of the system
Okay, Thank you for your kind support..
Hey,, I can't even communicate to an AB ultra 3000. It was installled before I started this job and I can't get it to connect to my PC to set parameters. I'm using a USB to rs232 I made a cable using pin out, 2,3,5. Please any help is appriciated.
For an ultra 3000, you need a serial cable & a null modem.
Then setup a serial driver in RSlinx with the proper baud rate & it will communicate
appreciated. PC is USB only, I have a USB to serial. So I need the null modem cable then? Thank you for a very prompt response 🤜👍. New sub now..lol
@@freaky_jsn_killr1364 Yes, USB to serial cable...set the port used for the USB to serial baud rate to match as well.
Use device manager to verify port.
Use that port for the RSLinx driver as well
I did not mention I'm using the ultraware software to try to communicate.
@@freaky_jsn_killr1364 You still need to use the technical setup as discussed.
Yes, I used to work with Ultra 3000.
Hope that helps
Thank You very much, I've been taking notes the whole video, very useful information, suscribe already, kind regards from México
Awesome, thank you!
You are a legend Shane, I haven't worked already with allen branley but with other manufacturers, in the way you are teaching I am learning a lot, thank you, and keep sharing your knowledge it is very important for us!
Thank you for the kind response, let me know if I can help.
Lmao you were clicking and typing things while you were talking about something completely different.
Sorry, I was slightly annoyed at the time so I was trying to prove a point.
By doing things as required plus talking about them as I did them but very quickly because someone talked smack in one of my previous videos not actually being 10 minutes to move.
I talked about the high points to keep this video short.
If you want more detail then search this channel using the search tab the type in the keyword you want to view.
It's simple and easy
@@ShaneWelcher Nice. Well, take an average of our complaints and you should be about right! 🤣
@@caleb7799 Take average ?
Don't you mean take advantage?
I put a lot of effort into helping people & answering questions, especially on RUclips so if someone doesn't like the way I teach, please note that RUclips is full of people that teach PLC logic.
Not near as in-depth however .
Also, feel free to miss out on all of the future videos I am releasing in 2023 about servos.
Not sure why people are heavy critics these days, it's a free video...i wish I had a place to turn to when I learned plc controls.
Seriously, there was no RUclips 20 years ago, much less an easy way to search for answers.
I think we should all be a little but more appreciative of anyone in the industry trying to help teach others.
Whether we agree with them or not, we should at least appreciate their efforts.
Just to let you know, I am very much appreciative of this video in 2024. Keep going Shane, and I appreciate this awesome content!@@ShaneWelcher
@@Abdiedits_ Glad to help, let me know if you would like to see any new topics
thanks for making these
Glad to help
Cool video!
Glad to help
Always awesome
Thank you for the kind words.
Coming next week, we are releasing two new videos per week for all of 2021 for training