Se for uma situação real onde a peça vai sofrer um esforço em alguma obra/servico, pode ser feita uma peça torneada com um comprimento maior que de uma única porca, abrindo rosca interna. Interessante poder ensaiar um conjunto também, nem que por curiosidade, para saber a resistência final da emenda
May not be a safe idea, even though held in position by the nuts, it may not take any axial, or longitudinal loads beyond a point, it will take to the extent the threads can withstand the load, since the entire cross sectional area of the bolt is not available for tension and shear, all the stresses are borne by the thread only. The cross sectional integrity should be available in its entire length minus the thread as a single straight piece, without splits! Tightening with a nut at the split location does not ensure integrity, it may not even be able to with stand combined bending and shear stresses. Also the nuts on either side of the central nut are just tightened to hold the central nut in position but not locked,it is susceptible to loosening under vibration or under any dynamic loading. This methodology won't be safe and is prone to failure.
Какие удивительные люди... Сначала РАСПИЛЯТ ЦЕЛУЮ шпильку. Потом её "наращивают" гайками... Накуя,спрашивается,резать,если она изначально была целая ?😂😂😂
You cut a screw in half just to put it back together with nuts, but what if its two different screws because one is to short ? How are you going to get the threads to match up ?
Es cierto nivel que se alcanza Por ejemplo El agua tiene niveles extremos tanto de calor y de frío Mucho calor se evapora mucho frío se expande Lo mismo pasa con la materia gris cuando llegas al límite más alto de inteligencia solo te queda volver a empezar desde cero deinteligencia En calor llega a un extremo que no puede calentarse porque se evapora
А скрутить высокой гайкой ( длинно, если так понятнее, соединительная которая) религия не позволяет? Оба соединения говер, но моё хотя бы заводского качества😂
![COMO FAZER PROTETOR DE PORTA- [Veda Porta Passo a Passo] - Sob medida](/img/1.gif)
Не проще целый болт поставить и без трёх гаек👀
В степи не оказалось ни новой шпильки, ни муфты, ни сварки.Нашлись только ножовка и три лишние гайки.
😂👍 порвало кардан, в степи нет деревьев. Взяли два черенка и отремонтировали, это на мармоне , ЗИЛ 157.
🤝 Смекалка ☝️😉
@@user-ui6si8oe2db
Zrt zrt zrt
There are one piece unions that would be cheaper,and faster.
You forgot the JB Weld. She won't hold without some JB Weld.
Se for uma situação real onde a peça vai sofrer um esforço em alguma obra/servico, pode ser feita uma peça torneada com um comprimento maior que de uma única porca, abrindo rosca interna. Interessante poder ensaiar um conjunto também, nem que por curiosidade, para saber a resistência final da emenda
0😊
May not be a safe idea, even though held in position by the nuts, it may not take any axial, or longitudinal loads beyond a point, it will take to the extent the threads can withstand the load, since the entire cross sectional area of the bolt is not available for tension and shear, all the stresses are borne by the thread only.
The cross sectional integrity should be available in its entire length minus the thread as a single straight piece, without splits! Tightening with a nut at the split location does not ensure integrity, it may not even be able to with stand combined bending and shear stresses. Also the nuts on either side of the central nut are just tightened to hold the central nut in position but not locked,it is susceptible to loosening under vibration or under any dynamic loading. This methodology won't be safe and is prone to failure.
There are better ways ,readily available- time a tolerances will allow you to go to town for a real fix.
Ya no es seguro, hay divisiones entre si.
😊😊😅😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😅😊😊😊😊😊😊😊😊😊😊😊😊😊😊😅😊😊😊😊😊😊😊😊😊😊😅😅😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊
Вообще то для этих целей ставят соеденительные гайки. Они длинные.
Причем уже сто лет как. Лавхакеры мамкины,бля.
Это просто если под рукой нет длинной гайки,а надо что то сделать
Muito bom mesmo parabéns
Threaded bar is cheap ....put a new threaded bar
Gotta love these clever repairs for something that will never be needed in 3 lifetimes...
I think it could have been tighter together first.
They make an all thread coupling for that.
Какие удивительные люди... Сначала РАСПИЛЯТ ЦЕЛУЮ шпильку. Потом её "наращивают" гайками... Накуя,спрашивается,резать,если она изначально была целая ?😂😂😂
cool idea, but I think I would just grab a new bolt.
Use a threaded rod coupling!
Yeah we call them a connector nut in Australia. We run thread rods up through the frame of a house to tie the frame down in high wind areas
If you are on some deserted island, this fix is perfect, just to make it back to civilisation, but other wise just buy a new bolt its cheap and safer.
You cut a screw in half just to put it back together with nuts, but what if its two different screws because one is to short ? How are you going to get the threads to match up ?
Should be good for a bird feeder
That looks structurally sound 🎉
Ае2235пл😊😅😮😢🎉😂❤
Куаяплшшш🤑🤑🤑🤑😇😁🤪🤪🤑🫢😬
Важна шрошшддлпа
Es cierto nivel que se alcanza
Por ejemplo
El agua tiene niveles extremos tanto de calor y de frío
Mucho calor se evapora mucho frío se expande
Lo mismo pasa con la materia gris cuando llegas al límite más alto de inteligencia solo te queda volver a empezar desde cero deinteligencia
En calor llega a un extremo que no puede calentarse porque se evapora
You forgot the little green check mark ✅️ and the bell
Заварить забыл, потом почистить, обезжирить, грунтонуть и покрасить😂😂😂
Works but don't count on it .perhaps a toilet roll holder
Существует удлиненная гайка , говорят помогает .
А ещё в електротоварах продают мозги😂
And you wonder why taking the cheapest bid possible is not the right way to go
Y eso que es ?
O para que es?
Para que sirve?
Que novedad tiene?
Shoot, I missed it. What did we fix?
Não entendi para qual a finalidade além
Right! But why would one ever need to do that? Would be a very rare occasion.
How boeing handles a broken screw
Threaded rod must be expensive where you come from
A rod coupling and two square cuts might work 😂
When a chronic runs out of material
For what reason??I've been hanging threaded rod for 25 years never needed a reason to cut at a angle and splice
Существует длинная гайка
Why did you cut the all thread in the first place?
Pq corta à bara d rosca p/ emendar dinovo
Ты будешь удивлин,но есть гайки 10 сантиметров,муфтами называются
10 centímetros ? Seguro de eso
Ты будешь удивлён, но они не везде есть
@@Vyacheslav_Tyson Кто ищет,тот найдет
What is the purpose of
This. Understand the project only why
And when we going to use this ?😮😮😮😮
저런건 배우고 싶지 않아요 차라리 새것으로 작업 하는게 더 안전해 보여요
Just... just buy a new one?
Oh right...because everyone in construction would use this.
you need a "rod coupling", you are welcome
For what purpose?
Who in the hell cuts a bolt in half to use this hack. Really
Соединительная гайка ?Не неслышал.
Great idea .
Ahhh , just go buy a coupler or a new all thread
Or use a rod coupling
Buy a longer threaded bar
Si no es la única pieza que exista para que no se pueda reemplazar
У нас в России для этого продаются длинные гайки.
Wow amazing🎉
Чудеса, да и только.
No des perdiciemos pensemos
Gostei
Ya i run into this problem all the time 😄
U just created a week joint
Обычное соединение карабина поводка собаки. Ни чего здесь оригинального нет.
ฉันคิดว่ามันค่อนข้างจะทำยาก ตอนปาดปลายตัองให้องศาพอดีกัน😅
This is some chinese tofu construction
1978 год, у меня так елка собиралась 😂
Isso e gambiarra e botar vidas em risco isso não procede a pessoa tinha que ser inteira
Why not use a rod coupling
Adesso ci puoi costruire una casa con uno come quello.......
Sigo recargaó en la pared...!!!🥴
Joining two metal bars
You clearly cut that yourself what is the point
А сверху замотать изолентой. Синей.😅
Я тоже всегда так делаю.Правда,еще не придумал,зачем.
Why to waste time ?
Que remiendo más barato cuidado con los charlatanes que hacen eso
У меня один вопрос, -нахрена????!
Отлично! А теперь трос лифта закрепить.
It won't work
That's something you do when you know you're about to be laid off in a one-man layoff.
Genial
Hur ofta lixom?
Very useful 👌 idea sir and thanks for sharing 👍 🙏 ❤
Ну точно развалится, ни изоленты ни подорожника...
Yeaaa.... that's not a strong as you think.
Neue Gewindestange wäre ne brauchbare Option
Thats a poor joint
It's not used this idea on a motor bike 10yrs back still OK
Clever
That's fine send it nobody will get hurt
To jest genialne 😮❤
Нет.
🐧 Dazu ein Materialtest wäre
wünschenswert.
А для чего это?
Y eso como para que
Ya, like that will work. Lol hahaha
А зачем? А для чего? Что делать было нечего? Это дурдом!
Это когда нет длинной гайки, но есть время
But..... why?
А скрутить высокой гайкой ( длинно, если так понятнее, соединительная которая) религия не позволяет? Оба соединения говер, но моё хотя бы заводского качества😂
Why?
Good
すべてのナットが同じ方向に動かないとする根拠は？(笑)
そう言うのを 手抜き 工事って 言うんだよね
That is very smart I never thought of that but today I learned something from RUclips
You learned what an idiot would do. Don't ever repeat this lunacy
И для чего это?
E quindi ?😮
Poor practice means poor product.
forbidden
tell me what is the reason