Copper sulphate को पानी में घोल कर उनमें से 1 चम्मच लेकर उसमे नमक मिलाओ और उससे एल्युमिनियम वायर साफ करो। फिर वायर पर कॉपर सल्फेट वाला पानी लगाओ इससे प्रॉपर कोटिंग होती है एल्युमिनियम पर कॉपर की । अब इस पर नॉर्मल सोल्डरिंग कर सकते हैं।
Good information। Ik na jo gadion ke radiators rep kartein hain unke pass ik liquid hota hai Pani jesa shyd bettry ka acid ho vo us ko lga kar gass velding se tanka lgatyein hai। Me bhi use krta hun।bhut asha work krta h। Copper pe bhi lohe pe bhi aluminium pe bhi pittal pe bhi।
Batter aluminium soldering karne ke liye Kuch step hai 1) Use a High-Quality Aluminum Flux:Purpose: Aluminum flux is designed to remove the oxide layer that naturally forms on aluminum. A high-quality flux is essential for creating a good bond between the solder and the aluminum wire. 2) Use a solder specifically designed for aluminum, typically containing a higher percentage of zinc or silicon. This type of solder is more effective at bonding with aluminum.Temperature: Ensure your soldering iron can reach a high enough temperature. 3) Clean the Aluminum Surface:Surface Preparation: Before applying the flux and solder, thoroughly clean the aluminum wire with a fine abrasive pad or sandpaper to remove any oxidation or contaminants.Immediate Soldering: Solder immediately after cleaning to prevent the oxide layer from reforming. 4) Maintain Heat and Pressure:Heat Application: Aluminum dissipates heat quickly, so use a soldering iron with sufficient power (high wattage) to keep the wire at the necessary temperature.Pressure: Apply gentle pressure with the soldering iron to ensure good contact between the wire, flux, and solder. 5) Seal the Joint:Protective Coating: After soldering, seal the joint with a protective coating like heat-shrink tubing, epoxy, or silicone sealant. This prevents moisture and air from reaching the joint, which could cause oxidation and weaken the bond over time.Crimping: As an additional step, consider crimping the connection before or after soldering for added mechanical strength. 6) Consider Alternative Techniques:Ultrasonic Soldering: This technique uses high-frequency vibrations to break down the oxide layer without the need for flux, creating a strong bond similar to that of copper soldering. However, it requires specialized equipment.Mechanical Fastening: In some cases, using crimp connectors, screw terminals, or aluminum-specific connectors might offer better long-term reliability than soldering Thank you 👍
Copper sulphate को पानी में घोल कर उनमें से 1 चम्मच लेकर उसमे नमक मिलाओ और उससे एल्युमिनियम वायर साफ करो। फिर वायर पर कॉपर सल्फेट वाला पानी लगाओ इससे प्रॉपर कोटिंग होती है एल्युमिनियम पर कॉपर की । अब इस पर नॉर्मल सोल्डरिंग कर सकते हैं।
Wah kesav ji aapne sahi bataya dhanya hai aap
@@WerTech127 धन्यवाद आपका 🙏
आपकी दुकान कहा है दादा जी
बहुत अच्छी जानकारी दी सर आपने मेरे साथ भी ऐसा हुआ है लेकिन मैं समझ नहीं पाया इस चीज को
Good information। Ik na jo gadion ke radiators rep kartein hain unke pass ik liquid hota hai Pani jesa shyd bettry ka acid ho vo us ko lga kar gass velding se tanka lgatyein hai। Me bhi use krta hun।bhut asha work krta h। Copper pe bhi lohe pe bhi aluminium pe bhi pittal pe bhi।
Bilkul sahi kaha,aisi problem hamare sath ho chuki hai, aluminium par soldering hi nahi karni chahiye.😢😢😢😢
Pura vdo me apne acha bataya tha tab hi main ne ye kharida tha apke kahne pe
Good video. If we use cleaning toilets acid then we soldering properly.
दूसरे फलक्स के बारे में नही बताया वो कैसा रहेगा।
Batter aluminium soldering karne ke liye Kuch step hai
1) Use a High-Quality Aluminum Flux:Purpose: Aluminum flux is designed to remove the oxide layer that naturally forms on aluminum. A high-quality flux is essential for creating a good bond between the solder and the aluminum wire.
2) Use a solder specifically designed for aluminum, typically containing a higher percentage of zinc or silicon. This type of solder is more effective at bonding with aluminum.Temperature: Ensure your soldering iron can reach a high enough temperature.
3) Clean the Aluminum Surface:Surface Preparation: Before applying the flux and solder, thoroughly clean the aluminum wire with a fine abrasive pad or sandpaper to remove any oxidation or contaminants.Immediate Soldering: Solder immediately after cleaning to prevent the oxide layer from reforming.
4) Maintain Heat and Pressure:Heat Application: Aluminum dissipates heat quickly, so use a soldering iron with sufficient power (high wattage) to keep the wire at the necessary temperature.Pressure: Apply gentle pressure with the soldering iron to ensure good contact between the wire, flux, and solder.
5) Seal the Joint:Protective Coating: After soldering, seal the joint with a protective coating like heat-shrink tubing, epoxy, or silicone sealant. This prevents moisture and air from reaching the joint, which could cause oxidation and weaken the bond over time.Crimping: As an additional step, consider crimping the connection before or after soldering for added mechanical strength.
6) Consider Alternative Techniques:Ultrasonic Soldering: This technique uses high-frequency vibrations to break down the oxide layer without the need for flux, creating a strong bond similar to that of copper soldering. However, it requires specialized equipment.Mechanical Fastening: In some cases, using crimp connectors, screw terminals, or aluminum-specific connectors might offer better long-term reliability than soldering
Thank you 👍
इसमें कहीं यह तो नहीं लिखा है कि यह अल्युमिनियम वायर को कॉपर में बदल देगा सर जी इसको प्रयोग करना एक मजबूरी है बस
400 degree temperature per use karna padta hai jab soldering Sahi hoti hai
We manufacture aluminium soldering flux. It does not give any problem mentioned in your video.
brand? address? contact no?
aapna buy link dedo bhai
गुरू जी को राम राम❤❤जी
Sahi bat hai sir ise to aacha ghiske soldring hoti hai ❤
Thanks for sharing information
Good night 🙏
Lithium cell ko soldering keliye
Konsa past use kare
Bhai solding mat karana nahin to fat jayega 😂😂😂😂
आप….. भाईजी जानकारी ….. धन्यवाद
Very good information sir ji
good information 🎉🎉 good video
Fir kounsa flux use kare aluminum ko soldering k liye
Good Information❤❤😮
Video k liye thank you sir g
Mere fridge me pin jitne do chhed hogaye ice box me, unhe kaise sold kar sakta hu.
Bahot achhi jankari
Important information 👌
Bahut achha video sir
Sir fir aluminium wire ko soldering kaise kare
Bha kon sa use kare
Very good information sar jay hind Jai Shri Ram
Aluminum par parfact soldering karne ke liye
ऐलमिनियम सोल्डर व फ्लेक्स है।एलकापी व आई आर सेवन ऐसा मैंने डिप्लोमा टाईम में पढाथा
Badiya jankari di h thank you sir😊
Ha sir mere sat bhi problam hui
Sir phir kaise solder kare please es par video banaye
Sahi kaha bhai
Sar Humne comment kiya tha ki 200,300 watt coil ko kaise pahchane
Thanku sir🙏 (solution) =
Nahi quickfix se lohe or aluminium par nahi hota
भाई जी सुपर जानकारी देते हैं आप धन्यवाद
7 segment display kidhar milega saman
Good knowledge
Aap sab theek sacchai hain ek sacchai aur bata dijiye MB collection wale Jo MOSFET lagate Hain vah local hai ki original Sahi Sahi bataiye ga
Sir ji please mujhe 120 jinar number mit gayab ho to kaise pata kare ye jinar hai ya dayvod mujhe samajhaye
नो sirf diode hau
@@SkElectronicswork sir ji kuch samajh nahi aaya app ka Ripley
Thank you sir.
Aluminium kbhi kon sa pest estemal kare
Sahi hai black rust bhi jum jaata hai don't use this
Ek ek component check kar ke dikhoo Aisa video banaoo
Good information sir.
Jai shree Ram 🚩🚩🚩🚩
Sir ji ❤️❤️❤️
Mail करी थी भाई साब एड्रेस क्या है आपका amplifier का काम करवाना है
आप ने ये नही बताया की फिर कौन-सी सोल्डर/फेल्कस इस्तेमाल करना चाहिए .
आधी जानकरी दी.
Apne video dhyan se nhi suni btaya to connector lgao
Good information sir
तो फ़िर इलाज क्या है कोपर पे शोल्डिंग करने का भाई ,, नम्बर तो आप अपना देते नहीं
Sabse bada draw back ye he ki aluminium paste acidic hota he kuch din baad copper pad ko kha jata he bilkul kabhi dekhna
Bhai sk ji mobile ki video dala karo jo ap bataye
Eska koi or solution batao sir ji
Nice information
To sir iska matlb h ye product long life nahi h
Ram Ram ji ❤❤❤❤
May khud quickfix ka paste istaymal karta hu
Jai Shri Ram Mahadev ❤❤❤
Twist karke soldering karne ke liye Aisa pest banaya hai
Thankyou thankyou thankyou sir 🙏🙏🙏
Solution nhi diya!
Very good
Thenks sir
thank you sir
Sk sir ab pr kisi ka reply nhi dete koun koun yah baat mante hai...?
जय श्री राम
Good
Logon ko ullu banate hai. Gurujii.. Jai sree ram🙏🙏🙏
Logo ko ullu nahi banate hai sahi bat batate hai sahi Jankaari dete hai
Ok sir
Jai shree Ram ji ki ❤❤
@@Rajaroyalprajapati jo log ye products banate he sir..
@@Rajaroyalprajapati bhai me sir ko nehi bola. Mene bola jo ye product banate hai. Wo log ollu banate hai. 😄
😂😂😂time kharab kiya kon si chij life time chalti hai or koi topic nahi mila to yahi😂
જય શ્રી કૃષ્ણ
Good sir ji
❤❤Thank you sir❤❤
😢bhaiya humko bhi sikha do
कभी भी इस्तेमाल नही किया सर....जय श्रीराम.
Bilkul sahi han bhaie
Hii ser theq ser
Pahli Baat To aluminium ka tar wala Transformer use hi nahin karne ka Baat khatm
Mene bhi magaya tha लूटते हैं ये लोगो को भाई
Iska matlab hum aluminium par Soldering kar hi nahi sakte aur jo solution mil raha hai woh dhoka hai
Ha जी
Samjh gya bhai
Sahi hai bro❤
Hai sar
Sir aapse TV repair karana hai aapna number dena
jai shree Ram ❤
Solution
Ok
TRP KE LIEY SAB KARTA HAI YEH
👍🏻👍🏻👍🏻
Jai shree ram
JAY SHREE RAM SIR 🙏🙏🙏🙏
Kon kon hamko support karta ha plz like
Hello sir aapse contact karna hai number mil sakta hai aap ka
We manufacture aluminium soldering flux. It does not give any problem mentioned in your video.
How??
@@souvikmondal3046 we used specialized chemicals which make sure that the flux breaks the aluminium oxide layer very well to solder.
@@akshaykumarvyas please sir tell me the complete process