Te recomiendo colocar tu logotipo con tu nombre con marca de agua en tus videos. Así también ya sabremos que aquellos que difudan en otros canales o plataformas sean tuyos.
You're an absolute design and fabrication genius! So precise! Absolutely brilliant. Love the silent format and the showing of the tool use before the video. So glad I found your channel. Hope to achieve some of your precision! It is inspiring!
Excellent work my friend, very calm very positive, you are the first youtuber that I have seen that knows how to operate an electric screwdriver, no revving up two or three times, just calmly screwing the screw down, both you and the person who taught you deserve everything which will come your way as you travel through this life, thank you for the upload. Bob
Looked at several of these, and think this is the best. The type with rods and linear bearings are industrial grade, but far more expensive and harder to build. I used 3/4 "L" extrusions 1/8" thick, and mine is super accurate. Be sure to use the HDPE tape or your aluminum will gall and seize up.
Mind-blowing, you're a legend! The only thing I don't get is how this video has any dislikes, I suppose you made some people are little bit envious with your ideas :)
No he visto a nadie haciendo este trabajo más relajado y proliciozamente perfecto parece que estuvieras angelicalmente en un quirófano operando un paciente terminal admiro tú relajo felicitaciones
Siempre que lo veo, me parece que tiene manos de coufier y no puedo evitar pensar que cuando hace los trabajos, sus manos parecen estar desarmando una bomba atómica...!!! Mucha paciencia y precisión oriental !!! Whenever I see him, I think he has coufier hands and I can not help but think that when he does the work, his hands seem to be disarming an atomic bomb ... !!! A lot of patience and oriental precision !!
I am really happy that at least I got an useful video on how to use my circular saw (like that of yours purchased long back) in the video and was looking for a video to make a jig for it. Now your video has given me the hope of using it usefully. If you can share the wood pieces that are used to make it I will try to do it. Hope my request will receive your kind attention.
Nice! I patterned mine after a $700 Festool table that lets you hinge a panel from a panel saw up, and slide the work under it for a zero clearance cut. I built mine as a quick attach to a table saw to take advantage of the weight and flat surface. Biggest thing is devising a mount for the panel that's quick to mount and release, and accurate as 90 degrees... You lost a little cut with the stopper, as a longer piece would let the blade come close to the back support. I really did like how you made the crossbars adjustable!
Great! Excellent work and impeccable execution, friend! I'd be really interested in locating a link to what you call "Inexpensive aluminum frame for clamping".
Grwat jig and outstanding craftmanship. FYI I think if you had a link in the discription where to buy plans kit on all your inventions it would do very well
Hello there! I would rather use the end raiser as a perpendicular fence for the cross cuts. Because aligning each piece to the laser guide every time you will make a cut can be very tedious. I call "end raiser" to the support where the saw ends its travel. Use it to make the cross cuts. It will be faster that way. Just make sure it's perpendicular to the blade. Very nice jig though. I like the gauge for cutting any angles!
EXCELENTE DEMOSTRACION !!!! Se ve directamente la Tecnica del uso de las herramientas, tranquilo y seguro de la demostracion Very Very Very Nice and Congratulation.
Hi Thank you for sharing your fantastic ideas. I am finding very helpful. CAn you advise where you found your portable drill press or did you make it? It a nice small size to use anywhere . Thanks . Perry
Hi JSK-koubou! I'm your fan! You are responsible for my beginning with woodworking! Do you have the plan so I can buy this 6in1 circular saw crosscut jig? For me this is the most complete and safe jig to start cutting wood (this is my only affraid in the woodworking world...). If you have it, please share the link so I can buy it, please! Thank you so much! And please, keep going with these fantastic projects that I love to see so much!
@@jisakukobo Thank you for your reply. I love this one but to start on woodworking the investment on materials is very high. I prefer to create first the 6in1 and after that, after other projects, do that one. Do you understand?
Amazing woodwork an design but i would like to know where to get the full instructions to be able to reproduce some of your diy projects please greetings from Arizona
Hello, I turned out a big fan of your projects, I just can’t find the aluminum frame for clamping, I just find the square one, do you have the link of your that I can order? Thank so much, your videos are very educational
Hello, the circular saw is not touch the base right? But could cut very clear. What the distance between circular saw and wood base (that laser projected)?
hello sir good day...i'm just asking, what did you use the rail of the circular saw.....thanks never mind sir, i think it's plywood and aluminum tubular bar....thank again
Автор очень большой молодец! Респект! Но, есть очень много существенных ньюансов которые никак не озвучены. Самое главное - это сама пила, точнее её подошва, высота бортов 10мм где-то, без таких бортов точного реза в вертикальной плоскости достичь будет очень сложно. Найти в продаже такую пилу мне не удалось и врятли получиться за вменяемые деньги (цена скорее всего будет сравнима уже с нормальной торцовкой), повторить проект не представляется возможным. Так что красивое видео это одно, а реализация на практике совсем другое, увы(
![[How to make a circular saw crosscut jig] Flip-up type (perpendicular fine adjustment function)](http://i.ytimg.com/vi/2UEi-JrOJPQ/mqdefault.jpg)
If you find any unauthorized reproduction of the JSK-koubou video, please report it to me.
Thank you.
JSK-koubouビデオの無断複製を見つけた場合は、報告していただけると助かります。
Te recomiendo colocar tu logotipo con tu nombre con marca de agua en tus videos. Así también ya sabremos que aquellos que difudan en otros canales o plataformas sean tuyos.
PÑ
es 3b,
You're an absolute design and fabrication genius! So precise! Absolutely brilliant. Love the silent format and the showing of the tool use before the video. So glad I found your channel. Hope to achieve some of your precision! It is inspiring!
Excellent work my friend, very calm very positive, you are the first youtuber that I have seen that knows how to operate an electric screwdriver, no revving up two or three times, just calmly screwing the screw down, both you and the person who taught you deserve everything which will come your way as you travel through this life, thank you for the upload. Bob
Cortador.de.fierro.i ndicar.su.fa ricacion
Great video as always mate. Love the demonstration before the tutorial and once again, no irritating music! Love your work.
Awesome job. I appreciate that you show us its multiple uses first before the construction.
You should show links where to get all the parts and possibly offer to email instructions on how to build it, very nice set up you have.
Thanks for sharing. Your videos are very calming to watch. You can feel your tools are made with much pride and perfection.
Огромный лайк - этот человек МОЛЧИТ!!!!
Судя по рукам, аккуратности и розовому респиратору этот человек - девушка
@@МегаВольт-е2щ Да нет же, парень он.
congratulations! excellent working technique and impeccable execution.
Man, you are like a surgeon with DIY projects.
Руки откуда надо растут!!!👍👍
Dios le da a cada uno la forma de sobresalir. éste mudito tiene mucho ingenio, felicitaciones Dios lo siga bendiciendo.
Looked at several of these, and think this is the best. The type with rods and linear bearings are industrial grade, but far more expensive and harder to build. I used 3/4 "L" extrusions 1/8" thick, and mine is super accurate. Be sure to use the HDPE tape or your aluminum will gall and seize up.
I Love the sound of the operating tools. Mustang 🐎 feeling
Mind-blowing, you're a legend!
The only thing I don't get is how this video has any dislikes, I suppose you made some people are little bit envious with your ideas :)
No he visto a nadie haciendo este trabajo más relajado y proliciozamente perfecto parece que estuvieras angelicalmente en un quirófano operando un paciente terminal admiro tú relajo felicitaciones
Siempre que lo veo, me parece que tiene manos de coufier y no puedo evitar pensar que cuando hace los trabajos, sus manos parecen estar desarmando una bomba atómica...!!! Mucha paciencia y precisión oriental !!!
Whenever I see him, I think he has coufier hands and I can not help but think that when he does the work, his hands seem to be disarming an atomic bomb ... !!! A lot of patience and oriental precision !!
Outstanding construction! That was the clearest video without words that I have ever seen.
I am really happy that at least I got an useful video on how to use my circular saw (like that of yours purchased long back) in the video and was looking for a video to make a jig for it. Now your video has given me the hope of using it usefully.
If you can share the wood pieces that are used to make it I will try to do it. Hope my request will receive your kind attention.
Nice! I patterned mine after a $700 Festool table that lets you hinge a panel from a panel saw up, and slide the work under it for a zero clearance cut. I built mine as a quick attach to a table saw to take advantage of the weight and flat surface. Biggest thing is devising a mount for the panel that's quick to mount and release, and accurate as 90 degrees...
You lost a little cut with the stopper, as a longer piece would let the blade come close to the back support.
I really did like how you made the crossbars adjustable!
Interested in your drill guide - look very nice and so much better than what you normally see!
丸のこを買ったが小さい木材の切り方がわからず困っていましたがこれを見て救われました
Espetacular! Projeto prático e inteligente. Parabéns!
Great! Excellent work and impeccable execution, friend!
I'd be really interested in locating a link to what you call "Inexpensive aluminum frame for clamping".
ti seguo da poco ..devo dire che sei veramente bravo ...complimenti !
Grwat jig and outstanding craftmanship. FYI I think if you had a link in the discription where to buy plans kit on all your inventions it would do very well
Amazing, very nice and clean
Thanks
You should make a video on your portable drill press. I like the look and function of it. Thank you for video. Great work.
I'm struggling to find the extrusion used for the saw runners in the UK, anyone any ideas? Cheers!
Love this man's work!!!
Hello there!
I would rather use the end raiser as a perpendicular fence for the cross cuts. Because aligning each piece to the laser guide every time you will make a cut can be very tedious.
I call "end raiser" to the support where the saw ends its travel. Use it to make the cross cuts. It will be faster that way. Just make sure it's perpendicular to the blade.
Very nice jig though. I like the gauge for cutting any angles!
I saw a lot of your Videos, your Work is ausome.
Все очень аккуратно и красиво 👍
These videos are good. A pdf with measurements will be good as well.
You are a genius! Greetings from Argentina
Brilliant design. Thanks for sharing. Looking forward for your next video.
excelente o seu trabalho, abraços do Brazil
Excellent work and presentation of work and creation tool
This is the best cross cut jig i have seen on here. well built and thought through. you could actually sell this jig.
Great video, thanks! But I really wonder. What about the dust?
Mistrz. Proste i piękne.
Dziękuję.
EXCELENTE DEMOSTRACION !!!! Se ve directamente la Tecnica del uso de las herramientas, tranquilo y seguro de la demostracion Very Very Very Nice and Congratulation.
You are the winner out of all the others !. Can you make me one, I will buy it of you ?
I would like to know where you buy/are you made the steel drill support. Seems to be done using linear bearing and rod. Thanks for feedback
ruclips.net/video/a2kIJDhhZrg/видео.html
HI, I LOVE YOUR DESIGN. CAN I HAVE THE PLANS.... ARE THEY FOR SALE
У нас говорят - золотые руки
좋은 영상 잘 보았습니다
감사합니다
Hi Thank you for sharing your fantastic ideas. I am finding very helpful. CAn you advise where you found your portable drill press or did you make it? It a nice small size to use anywhere . Thanks . Perry
ありがとうJSK-koubou! 非常に良いと明確な教訓！
教えて下さい。
アルミのレールはどちらで販売してますか？出来たらサイズも教えて頂きたいです。
宜しくお願い致します。
innovative ...... i like the video. I hope the tutorial can be given with the material size ..
動画の中で手で木材をを抑えて切断する部分がありますが動画の演出の都合です。
通常は危険なのでクランプして切断することをお勧めします。
自作工房 para no molestar lo
Juan
و عليكم السلام و
窓枠の材料が、手に入りません。
アルミのアングルだと強度がイマイチで、いいものが無く困っています。
NO ES EL DIALECTO QUE YO MANEJO :p
@@OMARCAMPING No es un dialecto, es un idioma.
Good job!. Are the plans for sale?
very well made jig and video. thank you for sharing your work.
What are you using for dust extraction? Its spotless when you cut
Hi JSK-koubou! I'm your fan! You are responsible for my beginning with woodworking! Do you have the plan so I can buy this 6in1 circular saw crosscut jig? For me this is the most complete and safe jig to start cutting wood (this is my only affraid in the woodworking world...). If you have it, please share the link so I can buy it, please! Thank you so much! And please, keep going with these fantastic projects that I love to see so much!
There are no plans for this video.
I have a plan for an improved circular saw guide.
This is easier to use.
↓
ruclips.net/video/M1xYKw5FP-0/видео.html
@@jisakukobo Thank you for your reply. I love this one but to start on woodworking the investment on materials is very high. I prefer to create first the 6in1 and after that, after other projects, do that one. Do you understand?
Amazing woodwork an design but i would like to know where to get the full instructions to be able to reproduce some of your diy projects please greetings from Arizona
Maestro un saludo desde Ecuador mis sinceras felicitaciones x exelente trabajo ,le pediria de favor medidas y traducirlo en español gracias.
very nice! where did you get that portable drill press?
Hello, I turned out a big fan of your projects, I just can’t find the aluminum frame for clamping, I just find the square one, do you have the link of your that I can order? Thank so much, your videos are very educational
would love to buy the plans and please share info on the drill press jig.
ruclips.net/video/a2kIJDhhZrg/видео.html
Excellent job! Could you please post link to mobile drill press you are using?
This is a great jig - May i please have the dimension and the name of the metal you used
COOL! надо себе сделать такую направляющую.
This thing is just awesome! Well built man! Thumbs up!
Such precision! Nice jig. : )
japanese one
Отличная работа!
Nice. What material did you use for your circular saw track?
Does anybody know the source of the small black metal pieces he uses as scew clamps when cutting small wood? What is this? Seems perfect for this.
Great video👍 Clear and clean job..
Thank you!
Good job! Looking forward to your next video .... regards from Holland!
Very Nice project. May I know where to buy the drill guide you are using ?
Very good working!
Could you tell me the make of that drill press please? :)
Hi, what did you stick on the L angle to reduce friction with circular saw base?
impresionante amigo me encanta tu trabajo.
Excellent job it’s very simple and awesome one!
Great jig! Congratulations.
رائع بكل ما تعنيه الكلمة
شكرا جزيلا
great job done, informative and well self explanatory
Hello, the circular saw is not touch the base right? But could cut very clear. What the distance between circular saw and wood base (that laser projected)?
12:26 Blech Winkel ist nicht paralel zur Holz Kante angeschraubt - 1 Punkt Abzug. :-)
hello sir good day...i'm just asking, what did you use the rail of the circular saw.....thanks
never mind sir, i think it's plywood and aluminum tubular bar....thank again
Gongratulation. Exelent work and perfect video. I learned a lot.
Where can I get these forked clamps? Thanks.
実表の大きさは？どうもありがとうございます！ 素晴らしいビデオだと私はそれを作ります！
Hello nice project ... but I have a question for you. Is your circular saw not so noisy that your circular saw model is yours?
The best I have seen
Los mejores videos, le hablo desde colombia, alguno de los paisanos me puede indicar en colombia donde encuentro los materiales? gracias de antemano
Hello, really nice job. I understand it can be built in several sizes, but could you please share the measurements for this one? Thanks in advance.
Has anyone made this? How easy was it to get the parts? How much did it cost to make?
Block for avoiding material pintching ?
Great video ~ may I know how or where to get the portable drill press stand showing in your video ?
Would also be interested
Yes i want it also where to buy that drill press stand
can you rotate the saw baseto 45 degrees and make longer cuts at 45 degees? Say....12" long?
Класс. С удовольствием купил бы.
How do you ensure the parallelism of two rails of each lower and upper portion; and the parallelism between lower and upper rails? Thanks.
A speed square
Precise and useful. Thanks for sharing your idea!
Автор очень большой молодец! Респект! Но, есть очень много существенных ньюансов которые никак не озвучены. Самое главное - это сама пила, точнее её подошва, высота бортов 10мм где-то, без таких бортов точного реза в вертикальной плоскости достичь будет очень сложно. Найти в продаже такую пилу мне не удалось и врятли получиться за вменяемые деньги (цена скорее всего будет сравнима уже с нормальной торцовкой), повторить проект не представляется возможным. Так что красивое видео это одно, а реализация на практике совсем другое, увы(
Правильно - нюанс. Вряд ли. Получится.
★函状の物は直角、角度切を調整する為の物なのでしょうか？・仰々しい作りで意味が良く分かりません？★底板にアルミ材で凹レール2本が埋め込みされておりますが何の為の物にのでしょうか？？・切断する材料を押さえる金具の位置移動レールでしょうか？お教え頂ければ幸いです。
Hi, nice work! Are they some plans for this tool? Thanks
Am curious about that glue at 12:08? Anyone know?