How to program fsct6b for drone | Full installation and setup tutorial | In Hindi
HTML-код
- Опубликовано: 11 сен 2024
- Hi
I am glad to introduce you my new video. Hope you all will enjoy this video. If you enjoyed the video please subscribe to our channel.
Time Stamp
00:42 Components Required
01:32 Start Installation
04:20 Connecting Transmitter
06:56 End Points
07:57 Reverse
08:35 Subtrim
09:27 DR
09:50 Mode
10:12 Type
12:09 Mix
15:26 Switch Program
About this video - :
In this video I am going to show you the full tutorial for the configurations of flysky ct6b transmitter in hindi.
T6 download link
en.freedownloa...
DR - Dual Rate setup. There are ON and OFF columns. This setting is only relevant if your
radio is later configured to utilize dual rates by associating this function with one of the
switches. Since we recommend you have one of the switches set for Throttle Kill, and you’ll
eventually probably want to use Idle-Up/3D mode with the other switch, there are no additional
switches to provide this functionality. Dual rate can be thought of as selecting between two
“sensitivities” of the rudder and cyclic controls. Reacting too abruptly to minor control
movements can be difficult for a beginner or pilot who needs very precise control, while a stunt
pilot may want intensely sensitive control to perform tight rolls and loops. The pilot that wants
to loop and roll and then land on a dime would want to control how sensitive the controls are at
different points in the flight. Thus, these fields set what percentage of full-rate is desired in
each switch position (“on” and “off” are again misleading misnomers, since this is really an “A”
or “B” choice when either position could be the more sensitive one). At this stage in the setup,
set all the fields of at least one selection to 100
• EndPoint - Servo Travel limits.
• Reverse - Servo direction settings
• SubTrim - offset signal level per servo to assist in centering the servo to the model.
• DR - double ratio controls CH1, CH2, CH4 servo rates
• Mode - Determines which servos are controlled by each joy stick
• Type - tells the radio the type of swash plate that is in use.
• Thro Cuv - Throttle Curve settings
• Pitch Cuv - Pitch Curve settings
• Swash Afr - used to adjust swash plate travel up and down.
• Mix - Provides the ability to assign a switch or another channel input to influence the signal on
another channel. Typically used in the FS-CT6A radio to assign the Gyro Gain VR(B) dial to
channel 5 in order to control Gyro Gain, but more advanced control methods can be configured.
Playlists
Creative list: • Creative list | Creati...
RC cars: • RC cars | Remote contr...
RC planes: • RC planes | How to mak...
RC boats: • RC boats | Remote cont...
Flight controllers: • Flight controllers for...
Drones: • How to make a drone at...
Videos with brief explanation: • Videos with deep expla...
ESC calibration and transmitter binding: • ESC calibration and tr...
Unboxing's: • Unboxing's Videos | Dr...
Lipo battery: • Lipo battery Videos | ...
APM 2.8 flight controller: • APM 2.8 flight control...
KK2.1.5 Flight controller: • KK2.1.5 Flight control...
Transmitter and Receiver: • Transmitter and Receiv...
Shorts: • Playlist
Racing drones: • Racing Drones | How to...
For queries
Hindipoemcollection@gmail.com
Instagram
www.instagram....
Impossible creativity #impossiblecreativity #drones #rcdrones #racingdrones #flyskytransmitter
Bhai mera ct6b transmitter ka receiver work nhi kar raha hai kya karo or ek new buy karo kya receiver
Is that possible without binding ??
Yes
Not arming problem arahi hai bro plz help me 😢
Bro actually I forgot to save my default settings prgm to send me default settings ka file link
Bhai ct6b transmitter purchase kiya fir setup on computer than bind transmitter to receiver than asebbled Quadcopter than kk 2.1.5 flight control board than fix the wire kk board to receiver than setup the kk board than kk board two first and last switch press it than on transmitter throttle do full upp than on the transmitter than transmitter throttle do right side move than drone will arm and again transmitter throttle will do left in sede than drone will disarm but my problem was new ct6b transmitter purchase than I had make drone but firt we have to transmitter setup on computer for Quadcopter setup than we have do bind transmitter to receiver than setup on kk board
Sir, please contact me, I have buyed the whole Quadcopter making kit (APM 2.8) and getting few problems after assembling and calibrating on mission planner , and not able to find the solution on RUclips, please sir please otherwise my money will be wasted, please sir it's a humble request
Please provide Bi copter settings.
Sir... even after selecting port & connecting the transmitter the black bars on computer are not moving sir...
I followed all your steps.....
Sir plz help sir.. plz
check your channel settings
are the channels are on or off
@@impossiblecreativity sir same problem , digitalradio Wale software me bas connecting hi dikha raha hai
Contenu with this content