You could have built a Boeing 747 with the amount of work you put into this, though I gotta say it is a great design and your workmanship is immaculate. ❤🎉
I realize I’m late to the convo, but I’m new here. Should you find that the bead chain wears quickly, please note the Chevrolet Corvair serpentine belt routing. In short, it turns 90 degrees away from pulleys, and twists 90 degrees to engage the next pulley. Happy Holidays.
I referenced the Corvair fan belt design when I was building a threshing machine, but ended up needing the v belt to twist 90*(pulleys are perpendicular, like a + when viewed from above ). Took a little bit of adjusting of tension idlers to run just right, but once it’s dialed in the are no issues running at 800rpm under load.
Well done! My favorite shot was the simultaneous g code, arrows, and CNC. Very clean, well edited, and a lovely project. I'd love to see some details on how you make the molds, and any special attention needed to get it to flow where you expect
That's a good idea that didn't actually occur to me! Yes, you probably could 3D print them, they don't need to be all that strong especially if the mould is well balanced in the centre of the machine. One thing I didn't mention about the pulley design, is that the pitch of the chain actually gets smaller as the radius of the pulley decreases due to the shape of the link ends inside each ball. I measured this for the two diameters I needed, but I imagine it would be possible to write some parametric code to generate the pulleys automatically (maybe somebody has even already done this?)
@@AndysMachines Very interesting, thanks! I wonder if the variation in link length is consistent between manufacturers. Might have to buy some chain and play about...
Yes, I've seen people do that with toothed belts. It's not how they are designed to be used, but works ok for light loads. There are also round rubber belts that would work, but not being toothed they can slip so need a lot more tension.
Thanks! The large pulley was made from an offcut of nylon sheet/plate I had to hand that was the right size. You can see in the video that it doesn't machine as nicely as the acetal, I had quite a lot of melted fluffy stuff to clean off afterwards. HDPE would probably behave very similarly. I always prefer acetal/delrin for any machining, it cuts very cleanly.
I probably won't be using this machine for any terminator parts as it can only cast plastic and rubber resins. Yes, it does appear as if several machines I've built recently have only ever made terminator parts (not too far from the truth!). You'll get to see an example of what I'm making with this machine at the end of the next video.
Question since the Small pulley is stationary wouldn’t your chain just stay still thus not really matter where you put the master link as long as it’s one rev away from the pulley if you get what I’m saying
The chain actually makes its way continuously around both pulleys even though one is stationary. It can be hard to visualise, but at 12:50 you see me hold the arm stationary and rotate the hub (with small pulley attached), this is equivalent to rotating the arm around the stationary pulley.
It would be some extra editing but could you lower the volume during machining operations a bit? It's like machining without ear protection currently and I have to turn the audio way down.
Well I did decrease the volume for most of the machining, but in part 2 I'll make sure there's nothing above -10dB. I think it also depends what device you play it back on, some play certain frequencies much louder, I always use headphones when editing.
DIY = Do It Yourself That is, instead of buying a rotocasting machine, he made it himself. There's also nothing 'industrial' about the tools he used to make it either.
Yes, of course. I actually watch all their videos. Are you implying my surface finish is inferior?? Admittedly the finish on the pliers was pretty poor, it was some cheap gummy steel and not the sharpest endmill, also you are looking at it in extreme close up, but the finish really wasn't important to me as it was just a tool for a one-off job. (Joe Pie is another great one to watch too.)
You could have built a Boeing 747 with the amount of work you put into this, though I gotta say it is a great design and your workmanship is immaculate. ❤🎉
Hell, that welding tip alone is worth a sub!
Instant sub, right there.
AGREED!
I realize I’m late to the convo, but I’m new here. Should you find that the bead chain wears quickly, please note the Chevrolet Corvair serpentine belt routing. In short, it turns 90 degrees away from pulleys, and twists 90 degrees to engage the next pulley. Happy Holidays.
I referenced the Corvair fan belt design when I was building a threshing machine, but ended up needing the v belt to twist 90*(pulleys are perpendicular, like a + when viewed from above ). Took a little bit of adjusting of tension idlers to run just right, but once it’s dialed in the are no issues running at 800rpm under load.
Years ago a company produced cymbals by rotocasting, called Zanki.
I never knew how they did it, until today, after watching this vid.
Thanks
The welding tip is cool. I would expect there to be so many factors at play that the amount of warping becomes unpredictable.
Well done! My favorite shot was the simultaneous g code, arrows, and CNC. Very clean, well edited, and a lovely project.
I'd love to see some details on how you make the molds, and any special attention needed to get it to flow where you expect
Interesting little tool build. We shared this video on our homemade tools forum this week 😎
Thanks! Part 2 will be out in the next day or two.
Brilliant solution to the welding shrinkage problem.
Damn you Andy, 🤣 As soon as I saw the chain I thought about the connector link. Very interesting project and well done video. See you next week!!!
As always, Brilliant idea followed by superb execution. Thanks for sharing, Andy.
Thanks for the 90 degree angle welding tip.
3:30
Bloody clever tip for welding right angles.
Thank you for both the entertainment and the education!
Excellent video Andy and great welding tip!
Awesome work. Love the bead chain pulleys.
Nice design, interesting process!
Exceptional video, can't wait to see part 2
Really cool! Looking forward to some extraordinary casting results ;-)
cant wait for part two!!!
Love the ball chain pulleys, great idea. I don't have a CNC mill, but they look like they might print fairly easily?
That's a good idea that didn't actually occur to me! Yes, you probably could 3D print them, they don't need to be all that strong especially if the mould is well balanced in the centre of the machine.
One thing I didn't mention about the pulley design, is that the pitch of the chain actually gets smaller as the radius of the pulley decreases due to the shape of the link ends inside each ball. I measured this for the two diameters I needed, but I imagine it would be possible to write some parametric code to generate the pulleys automatically (maybe somebody has even already done this?)
@@AndysMachines Very interesting, thanks! I wonder if the variation in link length is consistent between manufacturers. Might have to buy some chain and play about...
@@cooperiseddid you find much? Sorry, I know it’s an old comment. Happy Holidays.
thank you. regards richard.
Cant wait for part 2
Great Video 👌
Always thought provoking thanks 😀
Nice, could use normal chain like on ships anchors too.
Ended on a cliff hanger. Great use of that chain, you’ve seen that spiral wrapped round belt stuff right?
I think a timing belt/tooth belt should also be able to rotate 90 deg without a problem.
Yes, I've seen people do that with toothed belts. It's not how they are designed to be used, but works ok for light loads. There are also round rubber belts that would work, but not being toothed they can slip so need a lot more tension.
Cliffhanger ending :-o Thanks for the video
Very clever, is the larger pulley blank made from shredded milk bottles via your shredding machine?
Thanks! The large pulley was made from an offcut of nylon sheet/plate I had to hand that was the right size. You can see in the video that it doesn't machine as nicely as the acetal, I had quite a lot of melted fluffy stuff to clean off afterwards. HDPE would probably behave very similarly. I always prefer acetal/delrin for any machining, it cuts very cleanly.
Will you be casting something for the Terminator? It seems most of your machines are used for this purpose. Great video, thanks.
I probably won't be using this machine for any terminator parts as it can only cast plastic and rubber resins. Yes, it does appear as if several machines I've built recently have only ever made terminator parts (not too far from the truth!). You'll get to see an example of what I'm making with this machine at the end of the next video.
@@AndysMachines Thanks; looking forward to the next video.
Question since the Small pulley is stationary wouldn’t your chain just stay still thus not really matter where you put the master link as long as it’s one rev away from the pulley if you get what I’m saying
The chain actually makes its way continuously around both pulleys even though one is stationary. It can be hard to visualise, but at 12:50 you see me hold the arm stationary and rotate the hub (with small pulley attached), this is equivalent to rotating the arm around the stationary pulley.
I got ya wasn’t sure would have to see it in action
Great job. It's a pity that your roller blinds don't work anymore, you know, given you've stolen the chain for this project. 🤣
Bom demais!
It would be some extra editing but could you lower the volume during machining operations a bit? It's like machining without ear protection currently and I have to turn the audio way down.
Well I did decrease the volume for most of the machining, but in part 2 I'll make sure there's nothing above -10dB. I think it also depends what device you play it back on, some play certain frequencies much louder, I always use headphones when editing.
Does this casting machine cast Arnold Schwarzenegger too?
With the right mould it could do!
@@AndysMachines Then all you need is liquid living tissue for the Endo Skeleton. :)
Unlike this design, the one I did a while ago was built like a russian tank...
-very tough?
-nah... just a really crude craftsmanship.
Muito bom !
a
It is not diy it is industry tools
DIY = Do It Yourself
That is, instead of buying a rotocasting machine, he made it himself. There's also nothing 'industrial' about the tools he used to make it either.
Have you ever watched "This Old Tony" or "Blondiehacks"? They get great surface finishes when they machine parts. Why do you think they can do that?
Yes, of course. I actually watch all their videos. Are you implying my surface finish is inferior??
Admittedly the finish on the pliers was pretty poor, it was some cheap gummy steel and not the sharpest endmill, also you are looking at it in extreme close up, but the finish really wasn't important to me as it was just a tool for a one-off job.
(Joe Pie is another great one to watch too.)