Thanks so much, really appreciate that. it has been a while but I try my best to make it more often. Thanks for taking the time. Always appreciated.rich
Hello. Have you unbinding the FPC Cable Earpiece via nand on an iPhone 11 or 12? I tried to find factory codes for iPhone XR and iPhone 11, but without result. I waited ~10 hours with one phone, but the programmer did not find the factory codes. Although it finds it on iPhone X in purple mode. The manufacturer claims support for unbinding via nand, quote: "X-12Pm disassemble and unbind, not limited to ios system,Use i2C P14Pro to query code and unbind after removing the hard disk"
Today my i2c arived. I'm new to this, so my question is, do I need to desolder my nand chip on iPhone se1 and above (iphone 7/7p for example)? Does free disasembly means plug n play, cause I keep getting error when I try to query factory code on my se and iphone7.... Thanks in advance.
Hi any device that’s a10 cpu or lower , the nand can be read or modified using the purple mode function which doesn’t require nand removal. Any newer the nand will have to be removed to read or modify etc. when first setting up, download the i2c platform software and then select the p14 pro section. This will then install the p14 pro software for you. Then plug the programmer into the computer. Then on the software select drivers from the menu. Once you’ve installed the drivers the programmer will appear in the software for use. It won’t work unless you install the drivers. Thanks rich
I purchased the P14 pro in May but didn't test it out until yesterday. I downloaded the latest softwares, tried to connect via i2cTools (my i6s is recognized correctly), and also through the P14Pro interface... Neither recognizes my P14. In Device Manager, It is recognized as a USB Generic Hub, so I uninstalled and updated the USB 3.0 drivers in Device Manager. I also added the Drivers from the i2C Tools screen, but I get "the drive is successfully pre-installed in advance!" message. My p14 shows "v 1.06" on its lcd screen. I assume it needs a firmware update, but if it doesn't connect, I can't do anything. So frustrating.
Hi to solve this issue you need to download and install the drivers from i2c. You can do this by opening the i2c platform and you will find the drivers in the the menu. Once installed it should recognise the programmer inside the software. If it opens the drivers and not installing the drivers when you try to, you may have to disable ‘driver enforcement’ inside windows to install. This is because windows sometimes stops you installing drivers that are not digitally certified by Microsoft . Hope this helps. Thanks rich.
Rich! you had me worried for second with the channel name change. I thought i didn't know any Surge only my hardware protection haha! Anyway if people clicking the link you showed in the video gets "Download blocked" Just click the "Continue to site" button and it will start the software download. I can confirm its clean, I did post the link but I guess RUclips deleted the comment 😑
😂😂I ended up changing it because there way too many ‘micro-repairs’ on here.😂, thinking about it ,the download link I showed in the video may of only worked because the opera browser I was using has a built in VPN. Glad there was a work around. Appreciate you taking the time. Thanks Rich
Ah yes the words Micro & Repairs do seem to show them self's a great deal in electronics. I honestly think the name you have gone with fits well. I tried to download the software via Chrome & Firefox with VPN on then i turned it off and still got the same blocked message. I did post the Link that included the IP to the software so i guess YT was right to delete it 😂
@@Ratchet_effect 😂😂thanks, not sure why that’s happening but I’ll have a look and see if I can get a better link, I’ll try and post a link to it in the description. I2c programmers are good for the money but the software a nightmare 😂
Hey Surge, I hope you are well ? Hey man I bought this programmer back in July and I have almost similar issues, but mine are kind of much worse. You see every time I try to update the software it says download or update failed ok. Then the P14 pro tool wont set in English and it’s say the language will be set once the software restarts nothing!!! I was on version 1.90 on p14 and 4.45 on tools when this happened before everything was perfect. If you have any solution or have it fixed by now please let me know because it’s affecting my work heavily. Thanks
The software for this programmer is so buggy that problems seem to arise from every update they release almost. One thing to try with the latest update, is to uninstall both of the programs from the computer completely. Then download the latest i2c platform program (the original one that’s shown in the beginning of this video). Then select p14 pro on the top left corner within the program itself (on the updated version of the platform )it will then download the latest version of the p14 pro platform shown later on in the video. Because it’s downloaded through the platform rather than the link it should work then. It’s a good programmer when it works but the software a nightmare unfortunately, the software updates are so buggy it almost makes it completely unusable at times. But hopefully that works for you as that’s how I managed to fix the latest issues. I’ll do an updated video soon on. Thanks rich
That’s a good question because I had server issues with the jc programmer p11. If the server down you can’t use it. Yes you can use it offline but within the i2c platform on the pc but certain functions like querying and purple mode need a connection. But to read and write , can be done offline. Thanks rich
where can i download the file for p14 pro? i saw a few pages online which people posted, but when i clicked download it kept giving me the p15 instead of p14. please help to guide me to the page where i download the correct the file for model p14 pro. TYMIA
Yes it has all the same options as the regular app, it has all the preset nand SYSCFG for all the models. When you select the model you can auto fill the data. Thanks rich
It’s most likely the drivers for the programmer haven’t been installed. Along the top of the software platform there should be a drop down menu and then select drivers. Once you’ve installed the drivers it should work for you. Rich
saludos, mi programadora llego con 1.69 y este programa tiene actualización 1.86 , lee la memoria , formatea, pero no reescribe la información guardada, me dice que actualice la maquina , pero por ningún lado dice donde ? tienes alguna solución .....ya escribí a servicio técnico veremos!
Hola, puedes actualizar tu programador conectándote a la computadora y luego abriendo la plataforma de software i2c p14 pro. en la parte superior hay un símbolo de flecha grande llamado "actualización del dispositivo". Si hace clic aquí, actualizará el firmware del programador al firmware más reciente. Con suerte, esto resolverá los problemas que ha estado teniendo. gracias rico
@@JHONNY徐杰尼 Intentaré encontrar una solución para usted. Normalmente debería actualizar el firmware de esa manera, no estoy seguro de por qué no funciona. Podría ser un dispositivo defectuoso, pero intentaré encontrar otra manera. gracias rico
@@SURGE101 saludos ya hable con la gente de soporte y listo cuando se hace un formateo profundo hay que colocar la nand de nuevo en placa para que haga las particiones y luego bajar y volver a montar, asi se recupera la informacion de la nand o board.... y lo otro es que si no quieres formatear a nivel cero o low, entonces se escribe una configuracion generica generada por la misma unidad y desde alli se puede borrar o hacer lo que desee dependiendo del caso,,,,, es muy rapida esta programadora ..... gracias por ayudar
@@hossamhrmobilerepair3656 i2c have updated the platform since this video, if you download and install the i2c assistant and then once you have created an account and signed in , select the p14 pro in the top left corner. It then install the p14 pro software for you and will open automatically through selecting it in the i2c assistant platform.
@@darriencriag2328 push the plastic down inside the programmer to reveal the pins inside the programmer and check they all come out properly and also cleaning the pins inside the programmer may solve this as it may be some dirt or something stopping the pins making a good connection with the nands.
@@darriencriag2328 I’ll try and find out a solution for you and ask around . It may be a fault with the programmer. Unfortunately I’m not sure what could cause this to be honest but I’ll try and find out for you.
![Who Wrote a Short Story That Seriously Disturbed a Teacher? | Dirty Laundry x Smosh [Full Episode]](http://i.ytimg.com/vi/bvHAy_rKoEI/mqdefault.jpg)
Hi Rich and good to see you back after a long while. Thank you for sharing and I am sure this will help others. I do not have one.
Thanks so much, really appreciate that. it has been a while but I try my best to make it more often. Thanks for taking the time. Always appreciated.rich
Thanks for sharing this solution. I had a lot of people messaging me asking for help.
Thanks Jesse, was a nightmare when it stopped working after updating. Rich
@@SURGE101 I needed this to work, since my JC P7 was also not working haha
Hello. Have you unbinding the FPC Cable Earpiece via nand on an iPhone 11 or 12? I tried to find factory codes for iPhone XR and iPhone 11, but without result. I waited ~10 hours with one phone, but the programmer did not find the factory codes. Although it finds it on iPhone X in purple mode.
The manufacturer claims support for unbinding via nand, quote: "X-12Pm disassemble and unbind, not limited to ios system,Use i2C P14Pro to query code and unbind after removing the hard disk"
Today my i2c arived. I'm new to this, so my question is, do I need to desolder my nand chip on iPhone se1 and above (iphone 7/7p for example)? Does free disasembly means plug n play, cause I keep getting error when I try to query factory code on my se and iphone7.... Thanks in advance.
Hi any device that’s a10 cpu or lower , the nand can be read or modified using the purple mode function which doesn’t require nand removal. Any newer the nand will have to be removed to read or modify etc. when first setting up, download the i2c platform software and then select the p14 pro section. This will then install the p14 pro software for you. Then plug the programmer into the computer. Then on the software select drivers from the menu. Once you’ve installed the drivers the programmer will appear in the software for use. It won’t work unless you install the drivers. Thanks rich
I purchased the P14 pro in May but didn't test it out until yesterday. I downloaded the latest softwares, tried to connect via i2cTools (my i6s is recognized correctly), and also through the P14Pro interface... Neither recognizes my P14. In Device Manager, It is recognized as a USB Generic Hub, so I uninstalled and updated the USB 3.0 drivers in Device Manager. I also added the Drivers from the i2C Tools screen, but I get "the drive is successfully pre-installed in advance!" message. My p14 shows "v 1.06" on its lcd screen. I assume it needs a firmware update, but if it doesn't connect, I can't do anything. So frustrating.
Hi to solve this issue you need to download and install the drivers from i2c. You can do this by opening the i2c platform and you will find the drivers in the the menu. Once installed it should recognise the programmer inside the software. If it opens the drivers and not installing the drivers when you try to, you may have to disable ‘driver enforcement’ inside windows to install. This is because windows sometimes stops you installing drivers that are not digitally certified by Microsoft . Hope this helps. Thanks rich.
Try a different usb type c cable
The one it cones with sometimes does not work
Had same problem and changing cable worked
Rich! you had me worried for second with the channel name change. I thought i didn't know any Surge only my hardware protection haha!
Anyway if people clicking the link you showed in the video gets "Download blocked" Just click the "Continue to site" button and it will start
the software download. I can confirm its clean, I did post the link but I guess RUclips deleted the comment 😑
😂😂I ended up changing it because there way too many ‘micro-repairs’ on here.😂, thinking about it ,the download link I showed in the video may of only worked because the opera browser I was using has a built in VPN. Glad there was a work around. Appreciate you taking the time. Thanks Rich
Ah yes the words Micro & Repairs do seem to show them self's a great deal in electronics. I honestly think the name you have gone with fits well. I tried to download the software via Chrome & Firefox with VPN on then i turned it off and still got the same blocked message. I did post the Link that included the IP to the software so i guess YT was right to delete it 😂
@@Ratchet_effect 😂😂thanks, not sure why that’s happening but I’ll have a look and see if I can get a better link, I’ll try and post a link to it in the description. I2c programmers are good for the money but the software a nightmare 😂
Hey Surge, I hope you are well ? Hey man I bought this programmer back in July and I have almost similar issues, but mine are kind of much worse. You see every time I try to update the software it says download or update failed ok. Then the P14 pro tool wont set in English and it’s say the language will be set once the software restarts nothing!!! I was on version 1.90 on p14 and 4.45 on tools when this happened before everything was perfect. If you have any solution or have it fixed by now please let me know because it’s affecting my work heavily. Thanks
The software for this programmer is so buggy that problems seem to arise from every update they release almost. One thing to try with the latest update, is to uninstall both of the programs from the computer completely. Then download the latest i2c platform program (the original one that’s shown in the beginning of this video). Then select p14 pro on the top left corner within the program itself (on the updated version of the platform )it will then download the latest version of the p14 pro platform shown later on in the video. Because it’s downloaded through the platform rather than the link it should work then. It’s a good programmer when it works but the software a nightmare unfortunately, the software updates are so buggy it almost makes it completely unusable at times. But hopefully that works for you as that’s how I managed to fix the latest issues. I’ll do an updated video soon on. Thanks rich
Does this programmer working offline?
Sorry for stupid question but I'm thinking to buy one.
That’s a good question because I had server issues with the jc programmer p11. If the server down you can’t use it. Yes you can use it offline but within the i2c platform on the pc but certain functions like querying and purple mode need a connection. But to read and write , can be done offline. Thanks rich
where can i download the file for p14 pro? i saw a few pages online which people posted, but when i clicked download it kept giving me the p15 instead of p14. please help to guide me to the page where i download the correct the file for model p14 pro. TYMIA
Hi I’ve done a more up to date video about this programmer, please check my latest video. Thanks rich
My question is does it auto fill data in like it did on the regular app?
Yes it has all the same options as the regular app, it has all the preset nand SYSCFG for all the models. When you select the model you can auto fill the data. Thanks rich
I noticed the standard prog didn't connect. Had to install a separate prog..
Tenho uma pergunta como vc fez pra resetar a memória. Pois na minha nova atualização não aparece mas
hi sir i have bought p14 pro after i downloaded the app it only '"Device Offline"" i don't know what to do with this.
It’s most likely the drivers for the programmer haven’t been installed. Along the top of the software platform there should be a drop down menu and then select drivers. Once you’ve installed the drivers it should work for you. Rich
saludos, mi programadora llego con 1.69 y este programa tiene actualización 1.86 , lee la memoria , formatea, pero no reescribe la información guardada, me dice que actualice la maquina , pero por ningún lado dice donde ? tienes alguna solución .....ya escribí a servicio técnico veremos!
Hola, puedes actualizar tu programador conectándote a la computadora y luego abriendo la plataforma de software i2c p14 pro. en la parte superior hay un símbolo de flecha grande llamado "actualización del dispositivo". Si hace clic aquí, actualizará el firmware del programador al firmware más reciente. Con suerte, esto resolverá los problemas que ha estado teniendo. gracias rico
@@SURGE101 muy agradecido por responderme !…. Pero lo e intentado varías veces y no me actualiza la programadora 🥹
@@JHONNY徐杰尼 Intentaré encontrar una solución para usted. Normalmente debería actualizar el firmware de esa manera, no estoy seguro de por qué no funciona. Podría ser un dispositivo defectuoso, pero intentaré encontrar otra manera. gracias rico
@@SURGE101 saludos ya hable con la gente de soporte y listo cuando se hace un formateo profundo hay que colocar la nand de nuevo en placa para que haga las particiones y luego bajar y volver a montar, asi se recupera la informacion de la nand o board.... y lo otro es que si no quieres formatear a nivel cero o low, entonces se escribe una configuracion generica generada por la misma unidad y desde alli se puede borrar o hacer lo que desee dependiendo del caso,,,,, es muy rapida esta programadora ..... gracias
por ayudar
The program does not send
Captcha
How do I activate the interface
Try again in a while, it may just be the server down. Or delete all your browser history and then try. May be an installed cookie problem.
@@SURGE101 I can't find P14 Pro only i2c assistan v4
@@hossamhrmobilerepair3656 i2c have updated the platform since this video, if you download and install the i2c assistant and then once you have created an account and signed in , select the p14 pro in the top left corner. It then install the p14 pro software for you and will open automatically through selecting it in the i2c assistant platform.
same problem
up same problem my p14pro
Can someone maybe help me?
Mine says incomplete hard drive partition
The nand works because it works in the phone, any ideas?
Try cleaning the pads of the nand, it may be the pins in the programmer are not making a good connection.
@@SURGE101 tried 3 nands same thing, might be the programmer itself being faulty.
It detects the nand but cannot program
@@darriencriag2328 push the plastic down inside the programmer to reveal the pins inside the programmer and check they all come out properly and also cleaning the pins inside the programmer may solve this as it may be some dirt or something stopping the pins making a good connection with the nands.
Thanks for your input
Yes I have tried that, even disassembled and reassembled the programmer
@@darriencriag2328 I’ll try and find out a solution for you and ask around . It may be a fault with the programmer. Unfortunately I’m not sure what could cause this to be honest but I’ll try and find out for you.
V1.14.20 2C P14 PRO PROGRAMMER NOT WORKING