I have a mikrotik router but it was hacked and the reset button is locked, the password is changed, so is there any way to reset it to default? thanks !
Any advice, my lhg5 powers on but only the first blue light shows up, hard reset also don't work, it cant be the rj45 of the device because how does it power on?
Hi… I have followed the Instructions, networking is setup correctly and router shows up as expected. However cannot select RouterOS package. Says 1-package found in directory but cannot view or select it. Can select folder but shows then blank "loaded 0 packages". There is certainly the routeros npk file in that folder I am trying to load. If I restart netinstall It then shows the package selected but install button is grayed out and key is not shown or visible. If I click on the displayed router it then shows the existing key but package selected disappears, is blank and shows "loaded 0 packages" again and unable to select install. And attempts to browse to the package location does the same problem as above, and does not show up. I have tried every combination of restarting netinstall and booting up the Mikrotik in netinstall mode while netinstall is running or not running. Same result.
Hi Sir I using RB750Gr3 with CC220C473F53/037/r4 with 6.49.3. I try to follow your procedure but it doesn't work...... There are two buttons. Rese and Mode button. It doesn't work. I can't using Winbox to connect to the 750G...... Please give me some advice.
Hello! How to perform netinst on RBcAPGi-5acD2nD(CAP ac)? Long story short out-of-box with v6.48 set to CAP mode, CAPsMan uses requiring same version - update to 7.5 started automatically, but powerloss occured and now this CAP is bricked.
Well, in case anyone needs solution. Answer is: there is no need to hold reset button(or mode button) in CAP ac case. You just need to connect it via PoE on Eth1 to a router. Connect your laptop to same router via ethernet. Run netinstall as administrator and enable "net booting" with IP from routers DHCP Server pool. After short few minutes CAP ac will appear in the list. Just choose it, mark needed routerOS installation package enable default configuration and click "Install" button. That's All, folks!
Can you perform a netinstall withour pressing the reste button on the device? Or is there any other way to reset the device f.e. if you have an antenna placed on the roof an you loose password.
Two options: 1) Go to product page and go down to downloads: mikrotik.com/product/knot_lr8#fndtn-downloads 2) if you can Connect to device, Winbox shows type in title bar, for example Audience (arm)
HELP!!! My router is HAP AC & it is not appearing in the list other than the Disk Drives in netinstall after following the procedure in toto. I even Reseted the device for 10 Minutes beforehand... Router is not identified in pc, Port LED is blinking, No wifi LED. Model: RB962UiGS-5HacT2HnT
Thank you for video tutorial. Can I ask you as technical support? What to do with netinstall in case if first ethernet port of mikrotik router (first of 5) is out of service (broken). But other ports works properly. Is it possible to reassign netinstall port ?
@@mikrotik Thanks for answering. Nothing happens when I hold the reset button. The blue led and 2 green LEDs turn on regularly without the sign given in the user manual Maybe this unit has some problem What can I do? I'm thinking of sending the lhg18 back
@@mikrotikthe blue led it remains always on. I did a similar procedure on hap ax3 to reset the device and after holding about five seconds the led starts flashing It's a pity, the combo lhg 18-hap ax3 works great I'm living 14 km from the BTS. To get an internet connection I had to get out the Huawei 818 and its antenna 😢
@@mikrotik thanks again. Usually the power source of lhg 18 is the port 1 of hap ax3, but for the netinstall procedure I'm using his 19.2W power source with POE. I'm going to try with the 36W power source of the hap ax3
Hello Miktorik support! I have SXTSQ lite5 and when holding the reset button and applying power after 20 sec the device still not visible in NetInstall application - what do I do?
@@mikrotik I looked at LEDs for probably a minute and it does not do anything. It simply starts last led and then blinks between LTE and Bluetooth symbol alternatively.
I am using the Mikrotik Chateau, using initial set up i changed password and updated manually. I then rebooted after reboot i switched off and now when i turned on later in the day the router shows a constant blue power led light and the other leds flash once every minute almost...I have tried to reset but the same thing happens. Please i need help
So is this not Compatible with windows 11? I tried it many times in many combinations with a Windows 11 laptop with USB ethernet and then Windows 11 Desktop with a PCI-E Intel NIC. Will not detect the router no matter what. Not sure why this crazy process is used, just need a boot interrupt and TFTP like the rest of the networking world.
Disconnect your computer from WiFi, Ethernet, LTE, or any other type of connection. Netinstall will only work on one active interface on your computer, it is highly recommended that you disconnect any other network interfaces in order to be sure that Netinstall will select the right network interface. And of course, disable firewalls and anti viruses
Hi brother I'm from Afghanistan ❤ There bro i have 3 mikrotik devices . 1 QRT 5 and 2 SXT 5 all is have the same problem. Can you help me please 🙏 😢 How can I contact you?
It saved my life. I had a power outage while upgrading my crs309. No other way of resuming it. Netinstall for the win!
Spent 1 hour on this, finally realized I need to disable my antivirus/firewall for it to work.
Great tutorial, I follow this video step by step and save my RB850G and cAP ac successfully. Thank you!
I have a mikrotik router but it was hacked and the reset button is locked, the password is changed, so is there any way to reset it to default? thanks !
thank you very much was so easy after this video
Наконец-то нормальная инструкция))
Simple and nice ! Thanks...
Thank you! I did it!
I forgot to turn off the wifi.
Is there another video for anLHG XL HP5?
my netinstall does not see my routerboard 951ui plus i cant reset it to defult manually
Any advice, my lhg5 powers on but only the first blue light shows up, hard reset also don't work, it cant be the rj45 of the device because how does it power on?
Thanks Oskars great tutorial.
Does this solution remove configuration?
This is my model " wAP ac LTE kit "
is my Architecture ARM 32bit or ARM 64bit and
can in installl Router os 7.1 with netinstall ? or not ?
Thank you very much
Thanks
thank you so much for the great video
thanks it work
Hello, how does it look like in rb1100ahx2, because I do not want netinstall to detect this router?
Not showing for me using D53G model
For what button Flashfig ?!
Could you please provide a similar video for users on Ubuntu?
The app is the same, instructions are identical
Hi sir thanks for this video the kindle of my device is set sq 5 high power it is software doesn’t appear on your main download page why
Thank you, is the process the same from MacOS via wine?
Hi…
I have followed the Instructions, networking is setup correctly and router shows up as expected.
However cannot select RouterOS package.
Says 1-package found in directory but cannot view or select it.
Can select folder but shows then blank "loaded 0 packages".
There is certainly the routeros npk file in that folder I am trying to load.
If I restart netinstall It then shows the package selected but install button is grayed out and key is not shown or visible.
If I click on the displayed router it then shows the existing key but package selected disappears, is blank and shows "loaded 0 packages" again and unable to select install.
And attempts to browse to the package location does the same problem as above, and does not show up.
I have tried every combination of restarting netinstall and booting up the Mikrotik in netinstall mode while netinstall is running or not running.
Same result.
Thank Q brother
Bro how to check current firmware in case of flashmood
Could you help me netinstall for Ubuntu Linux?
Hi Sir I using RB750Gr3 with CC220C473F53/037/r4 with 6.49.3. I try to follow your procedure but it doesn't work......
There are two buttons. Rese and Mode button. It doesn't work. I can't using Winbox to connect to the 750G......
Please give me some advice.
change version of netinstall and then shoud work, i have the same problem
where are the lord of the rings references? i got ''One router to delight them all'' and ' return of the king' already in your posts!
Hello! How to perform netinst on RBcAPGi-5acD2nD(CAP ac)? Long story short out-of-box with v6.48 set to CAP mode, CAPsMan uses requiring same version - update to 7.5 started automatically, but powerloss occured and now this CAP is bricked.
Well, in case anyone needs solution. Answer is: there is no need to hold reset button(or mode button) in CAP ac case. You just need to connect it via PoE on Eth1 to a router. Connect your laptop to same router via ethernet. Run netinstall as administrator and enable "net booting" with IP from routers DHCP Server pool. After short few minutes CAP ac will appear in the list. Just choose it, mark needed routerOS installation package enable default configuration and click "Install" button. That's All, folks!
*advice. If netinstall will fail, disable PC firewall.
Paldies Mikrotik!
Can you perform a netinstall withour pressing the reste button on the device? Or is there any other way to reset the device f.e. if you have an antenna placed on the roof an you loose password.
Not possible, because then other people could reinstall it too
@@mikrotikThanks, that was the answer i expectet! But i hoped there would be a way to do...
Sir how i know witch package for witch model number for mikrotik router
Two options:
1) Go to product page and go down to downloads: mikrotik.com/product/knot_lr8#fndtn-downloads
2) if you can Connect to device, Winbox shows type in title bar, for example Audience (arm)
HELP!!! My router is HAP AC & it is not appearing in the list other than the Disk Drives in netinstall after following the procedure in toto. I even Reseted the device for 10 Minutes beforehand... Router is not identified in pc, Port LED is blinking, No wifi LED. Model: RB962UiGS-5HacT2HnT
I have ccr1060- 12s-1s+rm
How do I reprogram it using net install?
I don't know eth boot
Follow the steps in the video.
Can it be bypass using console cable instead of using reset button for rb1200. Reset button is not working
Reset button always works, it is hardware locked to its function
@@mikrotik Not working for me either. :(
How to download firmware by name like 4011 router firmware
Look up your device on mikrotik.com/products and check architecture in the spec sheet - that is the type you need to download.
Any exact steps for hAP ac2? I tried so many times it never shows up.
Same directions. If not showing up, check cable and check if using port 1 on hap
Hi can downgrade to an old version
Thank you for video tutorial. Can I ask you as technical support? What to do with netinstall in case if first ethernet port of mikrotik router (first of 5) is out of service (broken). But other ports works properly. Is it possible to reassign netinstall port ?
You will have to repair the port first, there is no way to reassign Netinstall port.
@@mikrotik thank you for answer!
how recover mikrotik with PROTECTED BOOTLOADER enabled ?
You can’t. It would compromise security if you could
Great video! My lhg 18 had issues during update to 7.10.1 and now I'm unable to log in. Is this procedure valid for my device. Thank you
Yes, it’s valid for all MikroTik devices that run RouterOS- including yours
@@mikrotik Thanks for answering. Nothing happens when I hold the reset button.
The blue led and 2 green LEDs turn on regularly without the sign given in the user manual
Maybe this unit has some problem
What can I do? I'm thinking of sending the lhg18 back
@@mikrotikthe blue led it remains always on. I did a similar procedure on hap ax3 to reset the device and after holding about five seconds the led starts flashing
It's a pity, the combo lhg 18-hap ax3 works great I'm living 14 km from the BTS. To get an internet connection I had to get out the Huawei 818 and its antenna 😢
It could be a sign the power adapter is not poweful enough, try another power source. It could also mean some kind of damage to the unit.
@@mikrotik thanks again. Usually the power source of lhg 18 is the port 1 of hap ax3, but for the netinstall procedure I'm using his 19.2W power source with POE. I'm going to try with the 36W power source of the hap ax3
Will this work on the lhgg?
It works on all MikroTik RouterOS devices, including LHGG
Hello Miktorik support! I have SXTSQ lite5 and when holding the reset button and applying power after 20 sec the device still not visible in NetInstall application - what do I do?
Look at the LED lights. The LED will blink, then it will turn off. It can take even 25 seconds, so just monitor the LED status while you hold.
@@mikrotik I looked at LEDs for probably a minute and it does not do anything. It simply starts last led and then blinks between LTE and Bluetooth symbol alternatively.
@@victorruiz3318 hi , i have the same problem , how it solves
@@victorruiz3318 hi , i have the same problem , how it solves
And the sxtsq5 don’t have a IP address why
I did the same and it did not work. I have the device RB924i-2nD-BT5&BG77
I am using the Mikrotik Chateau, using initial set up i changed password and updated manually. I then rebooted after reboot i switched off and now when i turned on later in the day the router shows a constant blue power led light and the other leds flash once every minute almost...I have tried to reset but the same thing happens. Please i need help
I have the same problem
Did u resolve it😊
So is this not Compatible with windows 11? I tried it many times in many combinations with a Windows 11 laptop with USB ethernet and then Windows 11 Desktop with a PCI-E Intel NIC. Will not detect the router no matter what. Not sure why this crazy process is used, just need a boot interrupt and TFTP like the rest of the networking world.
Disconnect your computer from WiFi, Ethernet, LTE, or any other type of connection. Netinstall will only work on one active interface on your computer, it is highly recommended that you disconnect any other network interfaces in order to be sure that Netinstall will select the right network interface. And of course, disable firewalls and anti viruses
RB2011 does not work
New wAP AC LTE6 is wasted after first day. I'm tired with all that Mikrotik mess. I was fooled to "upgrade" from Zyxel, oh how I hate it all now.
At least, after 2 days of fight against RB2011.
Hi brother I'm from Afghanistan ❤
There bro i have 3 mikrotik devices .
1 QRT 5 and 2 SXT 5 all is have the same problem.
Can you help me please 🙏 😢
How can I contact you?
GRABE. PAG ENERVON GURO CHOI.