NEO-6M GPS Module unpacking and getting location using Arduino

[@liowwenan4054]

Very good demonstration, your video shows how the serial monitor and led indicator behave from not connecting to connecting the statelite. I searched plenty of video, none of them show the details as you're. Well done

[@laIlavaraz]

@@liowwenan4054 Thank you

[@Angkolgrandpa]

Can you help me? I didn't received any serial monitor

[@shaikummerumaan6529]

Thank you sir,Your content helped me a lot.

[@laIlavaraz]

@@shaikummerumaan6529 Thank you

[@assembled2062]

for me LED of NEO 6M is continuously blinking, can anyone help please

[@moazumwani]

sir i am not able to get all the GPGLL coordinates , I have changed 3 GPS neo 6m till now

[@dhananjaythakur7754]

Same problem dude

[@moazumwani]

@@dhananjaythakur7754 i works it takes some take go in open and try the gps

[@dhananjaythakur7754]

@@moazumwani bro, I don’t see any LED blinking or turning on since I bought it. I took it in my balcony, it didn’t work. Is there any Power LED on it? Or it just get lit up when it gets connected?

[@laIlavaraz]

It will blink when it's connected

[@dhananjaythakur7754]

@@laIlavaraz ok bro. So that means my work will be done when the Led starts blink right? That means, it does not have a power LED, it just has network Led whichever will blink after connecting. Right na bro? Can you please share the code or video you referred to. Did you connect it to 5v pin or 3.3v?

[@markneiltanap]

what if you upload a code and the rx tx is still connected i accidently upload it does the module now is broken?
someone please answer

[@karthik6233]

In my neo 6m after connecting to aurdino, the light in neo 6m in not blinking

[@laIlavaraz]

Check if there is sufficient power supplied

[@ArifFadhilah]

5:14 how long to wait for gps to get the signal??

[@laIlavaraz]

Some time according to the location

[@ArifFadhilah]

@@laIlavaraz can it find the signal if it indoor? The other youtuber said it's need to be outside because the signal can't through the concrete wall

[@laIlavaraz]

No it will work inside, but take some time to fetch the location

[@ArifFadhilah]

@@laIlavaraz ohhh i see, thanks for the reply, really great video btw

[@laIlavaraz]

Thank you too, also please subscribe 😊

[@znafesa3790]

how to connect it with esp32 ?

[@Sekhar_Home]

Can we connect its vcc pin with 5volt of arduino?

[@laIlavaraz]

No it will fry the chip!

[@Sekhar_Home]

@@laIlavaraz it has a LDO voltage regulator, it can support upto 5.5volt. My Neo 6m does not blink for GPS catch but the Serial monitor shows the accurate data..May be the led got fuse. Thank God.

[@Angkolgrandpa]

Can you help me, I didn't get any serial monitor

[@Angkolgrandpa]

How to debug if the serial monitor is not working? Cuz I didn't get any serial monitor

[@alphardminotaur2071]

​@@Angkolgrandpa I am also trying it but led is not blinking I have put it on the terrace for 3-4 hourse still not blinking😢

[@tgplayer6993]

What is the range of this

[@darshanbabu1142]

Hello, i connected my gps module with my esp8266 for the first time it worked but after that I'm not getting the latitude and longitude it's showing 0.000000 for both, even though led is blinking, I'm getting this problem, what's the solution for this??

[@assembled2062]

bro how did it work for first time ?? for me it is just continuosly blinking.

[@darshanbabu1142]

@@assembled2062 try printing the latitude and longitude, if it's blinking then the module is fine, might me mistake in your code, try debugging it

[@guujikenn]

where is the code

[@cubitechboy3103]

Hello Madhav Bhaiya😀😀😀😃😃

[@NoOne-br7bl]

where is the code?

[@sourabhvyas2070]

Where is the code dude

[@srinivasaprasanth]

I am not getting the location😴

[@laIlavaraz]

Please recheck you connection