Those wedge lock will fail at either the wedge end or the thread section, as the diameter on the thread has been reduced , here in NZ , because we have eqrthquake, it has been banned . This look like a very heavy structure , not sure why any engineer wants to design its columns and locate a splice high at the plastic zone like that... it is so wrong !
All the rebar are connected at same ....is there any code book where it is given that we can use 100% joint at same point of all rebar using coupler.....
for hong kong concrete code, coupler shall be used in the lapping point when steel ratio of the vertical element like r.c column exceeds 3.46%. The coupler shall be installed in a staggered pattern. they should not be arranged at the same level like the video shows.
Chota Muh Badi Bat, Magar Fir Bhi Mai Kahunga Ki Ye Tarika Sahi Nahi Hai, Aap Ye Tarika Istemal Kar Rahe Hain Kyuki Bhar Upar Se Niche Tak Proper Bana Rahe Aur Sariya Me Welding Ke Tarike Se Jod Na Pade Magar Mera Comman Sence Ye Kahata Hai Ki Aap Sario Ko Aapas Me Jodane Ke Liye Jo Coupler Ka Prayog Kar Rahe Hain Piller Vahi Se Fatega,
Escuela de Diamond Central le ofrece OSHA, SST10h full prevention , Flagger- banderas, Silica y Scaffold clases en español Direccion: 40-10 National St. Corona NY 11368 Tren 7, parada 103 Corona Plaza. Telf: 646-355-8895 / 646-666-8787 🚧👷
Those wedge lock will fail at either the wedge end or the thread section, as the diameter on the thread has been reduced , here in NZ , because we have eqrthquake, it has been banned . This look like a very heavy structure , not sure why any engineer wants to design its columns and locate a splice high at the plastic zone like that... it is so wrong !
All the rebar are connected at same ....is there any code book where it is given that we can use 100% joint at same point of all rebar using coupler.....
so nice
for hong kong concrete code, coupler shall be used in the lapping point when steel ratio of the vertical element like r.c column exceeds 3.46%. The coupler shall be installed in a staggered pattern. they should not be arranged at the same level like the video shows.
@@markx162 nice
Where can we buy this material?
F-TIVE SPLICING SDN BHD FROM MALAYSIA
F-TIVE SPLICING SDN BHD FROM MALAYSIA 2:13
@@boonpinthai5206please send company contact nut or E mail number. I want to buy this cupler
A jig and angle grinder to cut half lap joints and a stick welder would probably take as long, but be a lot lower tech and cheaper.
Sir ye tread karne wali machine ka naam Kiya Hain
Development length over lap 18× bar diameter equal s pull out and tensile strength in rebars. ACI 318 code in America.
thank you for your information.....
Need seamless steel pipe, boss?
How not to use a torque wrench! 🤦♂️
Why no crosswise horizontal-vertical rebar mechanical bolt connectors?
same question.....
Sir Punjab me kha SE Milata hai coupling
Var det for lite åver lapp?
welding would be faster and cheaper not to mention stonger
I only watched the video to see that dam torque wrench👍
Sett så dåli armert va holder dere på. Med? Skall vere rett.
This is big show a clamp can be replaced avoiding with this nechanis.
I think the ordinary method is better and gives longer and stronger bond between the starter and the continuation bar.
No
or just weld the 2 ends :)
nice solution.....:)
Bad solution. Easy to split
@@mrvalmonte197 nice
bad solution not proper attachement
@@mrvalmonte197 nope. Cut 2 half lap joints and weld the flats together. I do it all the time.
This is the best thing
Good improvement in construction👌
It takes time
yes you are right
good job
i can manufacting this products. plz reply me. if any people wants. i m from rajkot.
Chota Muh Badi Bat,
Magar Fir Bhi Mai Kahunga Ki Ye Tarika Sahi Nahi Hai,
Aap Ye Tarika Istemal Kar Rahe Hain Kyuki Bhar Upar Se Niche Tak Proper Bana Rahe Aur Sariya Me Welding Ke Tarike Se Jod Na Pade Magar Mera Comman Sence Ye Kahata Hai Ki Aap Sario Ko Aapas Me Jodane Ke Liye Jo Coupler Ka Prayog Kar Rahe Hain Piller Vahi Se Fatega,
Ngạc nhiên với cách làm này của các bác
Surely just welding on a new section would be cheaper and faster.
It would but welding rebar takes the strength out of it more liable to snap
@@Kt-ro2fm really? I doubt it.
I'm afraid so that's why rebar is tied not welded
@@Kt-ro2fm Not an expert but isn't rebar tied because that is all that is necessary and welding would be an unnecessary over kill.
@@Kt-ro2fm compared to the threads, i think welding is better. threads are weak too.
Escuela de Diamond Central le ofrece OSHA, SST10h full prevention , Flagger- banderas, Silica y Scaffold clases en español Direccion: 40-10 National St. Corona NY 11368 Tren 7, parada 103 Corona Plaza. Telf: 646-355-8895 / 646-666-8787 🚧👷
Why not just weld a piece on the end?
Rebar welding is not allowed here.
If u ask this question you must examine the civil engineering again.
exactly
Why does the song sound like it belongs in Minecraft
No sabe usar la dinamométrica
You lose your time weld it properly
exactly and so much effort
Time and added expenses, materials and especially labor. WELD THEM.!
Mujhe iska Kam aata hai
Joints are weak points 🙄
exactly
🙏🙏🙏💪💪💪
Nødløsning.
,👍
+ ou - , + ou - ...
Orrr just use longer rebar. 🤷♂️
Or just use longer Rebar