I watch this to see what the insides look like. I use a breadmaker to roast coffee with a heat gun. I wanted to do mods. After watching this I realized my breadmaker's shaft wasn't running as freely as your repaired breadmaker's shaft. I'll take this apart and do the maintenance. You may have saved my bread maker. Thanks.
I could not turn my brand new drive shaft so I plugged it in hit start and it began to pulse the paddle-and sounded perfectly normal.I made a white bread loaf-rechecked and found i could turn the drive shaft with some effort.My old machine can be rotated much easier.I will be checking this after each use to see if it continues to turn easier.
Shafts in general may have one of those spring steel C clips in a groove on the shaft holding it in place. Small slotted screwdriver or narrow tip pliers and a little impact to remove.
How did you remove the two rubber feet that are non-standard screws, like a split slot vs. the other two which were phillips head? I cannot find what kind of screws those are, and how to remove them. Thx
If it is a split slotted head, get a spare screwdriver and grind a bit out of the centre to clear the tab on the screw head. Sort of like grinding out a triangular screwdriver for those toys you aren't suppose to take apart.
Breadmakers doesnt have fuse i opened My up since the Belt was done i had to completly dissasemble My maker. Problem might be that safety switch thats screwed to motherboard is faulty bc u turned it on and immediately off. There is Little button. That you Press same as My water boiler.
I gave you a like because this gave me hope that it can be fixed, but as others have said there are gaps in the video that show the complete steps. Maybe once you get in there it becomes obvious, but those missing steps would have been helpful.
I watch this to see what the insides look like. I use a breadmaker to roast coffee with a heat gun. I wanted to do mods. After watching this I realized my breadmaker's shaft wasn't running as freely as your repaired breadmaker's shaft. I'll take this apart and do the maintenance. You may have saved my bread maker. Thanks.
YES! Thank you SO very much for this video! Exactly what we needed!!
I could not turn my brand new drive shaft so I plugged it in hit start and it began to pulse the paddle-and sounded perfectly normal.I made a white bread loaf-rechecked and found i could turn the drive shaft with some effort.My old machine can be rotated much easier.I will be checking this after each use to see if it continues to turn easier.
How you put the Walsh and the black magnet ring back? The magnet ring inner hole is much smaller
I agree with other comments.... wish you had shown us exactly how you got the shaft off etc. That was the important detail and the whole point!
Rhyannon Lallatin I would use a brass drift or punch. It will get damaged before the steel shaft.
Shafts in general may have one of those spring steel C clips in a groove on the shaft holding it in place. Small slotted screwdriver or narrow tip pliers and a little impact to remove.
This is why you always fill bread maker ingredients outside of machine!
How did you remove the two rubber feet that are non-standard screws, like a split slot vs. the other two which were phillips head? I cannot find what kind of screws those are, and how to remove them. Thx
If it is a split slotted head, get a spare screwdriver and grind a bit out of the centre to clear the tab on the screw head. Sort of like grinding out a triangular screwdriver for those toys you aren't suppose to take apart.
My machine doesn't want to turn on? No light?
Do you please have any solution for it?
LCD screen/circuit board shot? I don't know if these things have an internal fuse or not. Hard to tell without seeing it.
BigTideFun there's no sign of light in it. I guess because I started it and turned it off quickly without dough in it.
Breadmakers doesnt have fuse i opened My up since the Belt was done i had to completly dissasemble My maker. Problem might be that safety switch thats screwed to motherboard is faulty bc u turned it on and immediately off. There is Little button. That you Press same as My water boiler.
My kneading paddle won’t go all the way around can anyone tell me what’s wrong
Check for crumbs in paddle
How did you knock that shaft out?
I think it was a circlip that held the shaft in. Some tapping after that. Maybe after a bunch of forced twisting.
Indeed. Can’t get mine out either.
I gave you a like because this gave me hope that it can be fixed, but as others have said there are gaps in the video that show the complete steps. Maybe once you get in there it becomes obvious, but those missing steps would have been helpful.
Video does not show how to take apart
I think there was a circlip on the shaft that I removed before taking it out.