Great video man. Went through the same thing. I wish I had found your video at the beginning of the project. Great mentioning the gas coming out of the gas line because no one talks about it. It’s reassuring to know it isn’t a lot and it isn’t high pressure. I learned that by trial and error. Thanks for sharing
I just paid to have a mechanic replace that pipe. Note that I see your video I realize that I might have been able to tackle that. Next is my water reservoir bottle. My coolant level is fine but the sensor is broken so it shows “coolant low.” I may change that myself.
There is also a back counterpart to that front plastic flange. It could be cracked also if the leak persists after you do this repair. To get to it you just need to remove the intake manifold cover completely which he has hanging because he didn’t need full removal
Hello, I had the same leakage. I changed the coolant outlet flange, and the water pump. Turns out the coolant oulet flange was causing the leakage. My truck no longer has a coolant leakage but now my tempeture senser stays on cold for a while then it heats up half way then cools itself and then the temperature meter goes all the way to hot. Did anyone else have this problem ?? Do you know what could be causing this??
@@teddngo Yes the crossover pipe does connect to the back of the waterpump, when i had removed the leaking pipe i noticed the ends with the o-rings of the pipe were broken off and still in the engine block. i got a small pick and they pulled right out. i think its a bit of a bad design on jaguar land rovers part
May I ask..would you know if there is the same lay out on the 4.4 V8 of LR3 concerning this cross pipe? Also may I mention..if you still find coolant leaking in that area there is another Cross Coolant line at the other end off that engine.If you look on RUclips there is a video titled 2011 Range Rover Sport Coolant leak..or something like that..it shows the manifold completely off and that plastic coolant line going across the back...If our LR3 needs this job done as we are leaking a lot I will have them do both. How many hours do you estimate will take a professional Shoppe for this job with two lines replaced and manifold taken off as that back line will likely require it.? Nice video
In reply to your question you are correct, there is another similar looking coolant pipe near the back towards the firewall. I did change that particular one at a later stage when it did start to leak. The back one took approximately one and half hours from start to finish. The front pipe, I would allow at least fours hours. Lastly, only a suggestion do buy the parts required from the Land Rover Dealership, as I do not recommend the aftermarket ones from experience.
@@delllall Thank you...we have really been though it lately..We were worried that our engine (4.4 V8) would blow last weekend so we took it to mechanics on Monday who said they had no time very backed up leave it...they drove it..said they pressure tested it.. everything normal..found nothing..we picked it up Sat..drove it 16 miles got home every thing smelled like coolant..in 2 minutes 16" circle of coolant on the floor under car..back yard cats in danger.. So we were going to go back and tell them to check hoses that you point out in your video if they exist in the 4.4.. But neighbor who has been loaning us his truck all week long comes by and says let me see truck.He raises bonnet presses gas and you can hear something is not right..He says to my wife let's go for a ride..he drives it directly to a mechanic..on a Sunday at 6:30 pm that he knows who starts moving Hoses while neighbor presses gas..and my wife who is short says wait I see coolant spurting out under plastic engine cover.. They take cover off and one of the smaller hoses was completely broken..within 2-3 minutes it was diagnosed..Mechanic says the thin hoses are dry and cracking needing replacement and rigs up a temporary repair with a metal tube clamped down on each end to join hose till it can be replaced tommorow ..and car runs nice again. They diagnosed in two minutes what the other shoppe did not bother to do in 6 days..so we will have the 3 brittle thinner hoses replaced tommorow..and may God bless LR3 on past it's 173k miles on to many more.. thanks for the excellent video.
Great video man. Went through the same thing. I wish I had found your video at the beginning of the project. Great mentioning the gas coming out of the gas line because no one talks about it. It’s reassuring to know it isn’t a lot and it isn’t high pressure. I learned that by trial and error. Thanks for sharing
Thank you for sharing. I pray for a honest mechanic. 🙏🏼
Thanks a lot. Same thing happened mine. After watching problem solved.
I just paid to have a mechanic replace that pipe. Note that I see your video I realize that I might have been able to tackle that.
Next is my water reservoir bottle. My coolant level is fine but the sensor is broken so it shows “coolant low.” I may change that myself.
Nice video really helpful, this fixed my issue. Thanks for the info
Land Rover LR4 Water Tube Outlet part # LRO18275 PRICE RANGE FROM $20.00 to $67.00....on Ebay....more for the OEM...which I recommend.
Awesome video I replace my water pump still leaking and seen all the coolant around the same area as yours will be purchasing the y pipe 👍
Did you go with a genuine coolant tube or a aftermarket brand ?
hey, I have replaced the water pump + few hoses but the leak still remains & I hope my case is the same as yours. Thanks for the video, good job.
There is also a back counterpart to that front plastic flange. It could be cracked also if the leak persists after you do this repair. To get to it you just need to remove the intake manifold cover completely which he has hanging because he didn’t need full removal
I wish I saw this video a few hours ago, would have saved me $360. Anyway great video.
Same happening to me, I did change all. Even pump, connectors etc. And problem came back. Could lack of oil change cause overheat? thanks great video
Are there any type of gaskets you removed from the manifold? Also, once the fuel line is back on what about the pressurizing of it?
Hello, I change mine just now, and now it keep saying coolant low. Help me please?
Thank you for making this!
Cómo desalma el termostato de una land rover freelander 2000 motor 1.8
Sir, this cross pipe u raplace or rapair?
I mean if I putt silicon,it is ok
Hello, I had the same leakage. I changed the coolant outlet flange, and the water pump. Turns out the coolant oulet flange was causing the leakage. My truck no longer has a coolant leakage but now my tempeture senser stays on cold for a while then it heats up half way then cools itself and then the temperature meter goes all the way to hot. Did anyone else have this problem ?? Do you know what could be causing this??
I have a 2012 Range Rover Sport that had the same issue, i changed the cross pipe and it seemed to fix the leak. p/n LR018275
This is the same part number for a 2013 LR4 5.0L
@@teddngo Hello Tedd! if your vehicle has the Jaguar 5.0L v8 engine, it will work
@@JimmyJ-6920 Thanks Jimmy! I just replaced the water pump but have massive leakage behind it so I imagine its this crossover pipe.
@@teddngo Yes the crossover pipe does connect to the back of the waterpump, when i had removed the leaking pipe i noticed the ends with the o-rings of the pipe were broken off and still in the engine block. i got a small pick and they pulled right out. i think its a bit of a bad design on jaguar land rovers part
Thanks . Right on.
Water Outlet - Land-Rover (LR018275)
Is this the bmw v8?
May I ask..would you know if there is the same lay out on the 4.4 V8 of LR3 concerning this cross pipe?
Also may I mention..if you still find coolant leaking in that area there is another Cross Coolant line at the other end off that engine.If you look on RUclips there is a video titled
2011 Range Rover Sport Coolant leak..or something like that..it shows the manifold completely off and that plastic coolant line going across the back...If our LR3 needs this job done as we are leaking a lot I will have them do both.
How many hours do you estimate will take a professional Shoppe for this job with two lines replaced
and manifold taken off as that back line will likely require it.?
Nice video
In reply to your question you are correct, there is another similar looking coolant pipe near the back towards the firewall. I did change that particular one at a later stage when it did start to leak. The back one took approximately one and half hours from start to finish. The front pipe, I would allow at least fours hours. Lastly, only a suggestion do buy the parts required from the Land Rover Dealership, as I do not recommend the aftermarket ones from experience.
@@delllall Thank you...we have really been though it lately..We were worried that our engine (4.4 V8) would blow last weekend so we took it to mechanics on Monday who said they had no time very backed up leave it...they drove it..said they pressure tested it.. everything normal..found nothing..we picked it up Sat..drove it 16 miles got home every thing smelled like coolant..in 2 minutes 16" circle of coolant on the floor under car..back yard cats in danger..
So we were going to go back and tell them to check hoses that you point out in your video if they exist in the 4.4..
But neighbor who has been loaning us his truck all week long comes by and says let me see truck.He raises bonnet presses gas and you can hear something is not right..He says to my wife let's go for a ride..he drives it directly to a mechanic..on a Sunday at 6:30 pm that he knows who starts moving Hoses while neighbor presses gas..and my wife who is short says wait I see coolant spurting out under plastic engine cover..
They take cover off and one of the smaller hoses was completely broken..within 2-3 minutes it was diagnosed..Mechanic says the thin hoses are dry and cracking needing replacement and rigs up a temporary repair with a metal tube clamped down on each end to join hose till it can be replaced tommorow ..and car runs nice again.
They diagnosed in two minutes what the other shoppe did not bother to do in 6 days..so we will have the 3 brittle thinner hoses replaced tommorow..and may God bless LR3 on past it's 173k miles on to many more.. thanks for the excellent video.
Mines leaking like a crazy would it be Easier to remove the oil filter ?? How much was the replacement part ?? Thanks for for the info
no need to remove the oil filter housing.
How did you remove the fuel line what kind of socket did you use
My comment comes in late but I had the same issue and used a crowfoot wrench (not sure if UK name is different)
Greetings... how long of a job is it
It should not take more then 3 hours all round.....at a gentle pace.
What's the part number I have the same problem
Water Outlet - Land-Rover (LR018275)
Was there a gasket that needed to be replaced for the air intake manifold?
I would replace anything that is accessible at this stage of repair.
yes, there are 8 gaskets. @@delllall
These vehicles are the worst.....
Disagree. Maintenance is key to long rover life. It's just what you have to do.
@@charlesmaroon8819 you'll be maintaining your ass off.