Thanks for the video. Helped me a lot with the conversion of my R9T racer. These small screws on the switches, then one hidden. I would never have found it. Thank you!
Good set of videos, mate. Very useful as I pick up my bike tomorrow and want to do some of this stuff myself. I know you will have thought of this but you really need to get that swingarm powder coated in black.
Josh, no adaptor required. I used the OEM mushroom bar ends to lock in the mirrors. The locking is achieved by the push action from the mushrooms + the tightening of the mirrors screws. It gets a bit tricky with the throttle bar, because if u tighten too much, the throttle will lock. You just have to find the sweet spot were the mirrors are tight and the throttle is free to move back and forth
Is it true that when you switch clip ons, the turning radius of your bike is limited since the clip ons would hit the gas tank when you turn to the extreme left/right direction?
Thanks mate. The majority of the items were purchased from eBay or AliExpress The guage: #Aliexpress AU $87.70 | Oil Temperature Gauge - Celsius BLACK/SILVER / R NineT Scrambler for BMW R NINET R9T Roadster Scrambler Pure a.aliexpress.com/_dSOHA8I
The forks are the trickiest part You will need to disassemble the gold tubes, anodise them, the assemble them again. It's gonna be a very messy job if you're not familiar with forks rebuild. I opted for wrapping them, but you'll need to do it with the forks are installed in the triple tree clamp, otherwise, the wrap will get scratched when putting the forks back into the clamp Option 3, buy black forks, but they cost a fortune!
@@ahmadsammani2704 I already installed clip ons and it's really not that bad, 2 hour trips are no problem, although I don't have any back pain just my wrists start to hurt a bit
How high were the risers or what height did you set them at? Also how does it affect your riding position (ergonomics) do you recommend this set up for commuting (60 miles one way)?
60 miles is a bit too long for this riding position. After 20 miles u'll start feeling back pain. My commute was about 10 miles so it was fine Height wise, I've put them pretty low, u can adjust the height up to 5mm lower than the standard handle bars height
Thanks for the video. Helped me a lot with the conversion of my R9T racer. These small screws on the switches, then one hidden. I would never have found it. Thank you!
Great video, brother! I was a bit concerned about doing this myself, but after seeing you do it, I feel more confident. Cheers and ride safe!
Good set of videos, mate. Very useful as I pick up my bike tomorrow and want to do some of this stuff myself. I know you will have thought of this but you really need to get that swingarm powder coated in black.
Thanks!!! you have a ninet great!! from Sonora, México!
What a nice video, looks really good that R ninet!
Looks so good with clip ons
Great vid , very helpful
Do you recall the size of the Torx screw on the right controller? The screw on the outside to take off the cover.
"I wanna blacken the shit out of it...yeup" hahaha couldn't have said it better myself.
Looks great mate. Can’t seem to find these clip ons. What brand? Link no longer there
Hey Ahmad, was wondering how you got the bar end mirrors on the stock OEM handlebars as well as getting the OEM barends on...did you use an adaptor??
Josh, no adaptor required. I used the OEM mushroom bar ends to lock in the mirrors. The locking is achieved by the push action from the mushrooms + the tightening of the mirrors screws.
It gets a bit tricky with the throttle bar, because if u tighten too much, the throttle will lock.
You just have to find the sweet spot were the mirrors are tight and the throttle is free to move back and forth
Perfect Video. Your bike looks so much better. Did you change the cables for the brake or clutch? Aren't the original ones too long? Regards
Thank you Martin. Much appreciated
Didn't change any cables (just in case i decide to go back lol)
Is it true that when you switch clip ons, the turning radius of your bike is limited since the clip ons would hit the gas tank when you turn to the extreme left/right direction?
Not necessarily. It depends on your angle set-up.
If u wanna go for the cafe racer look, then yes, you'll be limited
Great video. Would you share a list of some of the other parts you have there? Love the gauge cluster.
Thanks mate. The majority of the items were purchased from eBay or AliExpress
The guage:
#Aliexpress AU $87.70 | Oil Temperature Gauge - Celsius BLACK/SILVER / R NineT Scrambler for BMW R NINET R9T Roadster Scrambler Pure
a.aliexpress.com/_dSOHA8I
keep the fork gold!
I just blacked out mine and just have the forks left. What are you going to do to black them out?
The forks are the trickiest part
You will need to disassemble the gold tubes, anodise them, the assemble them again.
It's gonna be a very messy job if you're not familiar with forks rebuild.
I opted for wrapping them, but you'll need to do it with the forks are installed in the triple tree clamp, otherwise, the wrap will get scratched when putting the forks back into the clamp
Option 3, buy black forks, but they cost a fortune!
Where did you buy the Speedometer ?
i wanna put clip ons on my rninet pure so bad as well but im worried about the riding position, how uncomfy does it get with the clip ons?
If you get the adjustable risers, not the bad. I can go 30 to 45 mins without backpain. Longer trips will have their toll
@@ahmadsammani2704 I already installed clip ons and it's really not that bad, 2 hour trips are no problem, although I don't have any back pain just my wrists start to hurt a bit
How high were the risers or what height did you set them at? Also how does it affect your riding position (ergonomics) do you recommend this set up for commuting (60 miles one way)?
60 miles is a bit too long for this riding position. After 20 miles u'll start feeling back pain. My commute was about 10 miles so it was fine
Height wise, I've put them pretty low, u can adjust the height up to 5mm lower than the standard handle bars height
Beautiful motorbike ! Do you think it's possible to do a short travels with a partner?
Yeah. I take my miss's all the time
@@ahmadsammani2704 thanks 😎
Bike looks great Ahmed! do you still have the powder coated original bars?
Samuel.. still do, but they're not powder coated, i made the mistake of spraying them with normal spray paint. Turned out rubbish
Ahmad Sammani 😂😂😂 disaster!! Doing a great job with the bike mate keep it up
Looks the part but it would do my back in ;-)
Thanks. very useful!
Cheers mate.. appreciate it
Do you have the link for the mirrors?
How have the clip ons holding up?
Very well. No issues so far
Also, link to those mirrors please
the original stems cannot be looked at turns the stems upside down
What brand are the clip ons? What’s the rise?
The link is in the description or you can use these
www.ebay.com.au/itm/333544117488
The rise is adjustable
what size mm are your forks? my r nine t forks are 43mm would these fit?
My forks are 55mm
I think if you look up 43mm, you'll find
Aussie
Hi I saw a link you gave someone it doesn’t look like the ones you have in your video ?
@@stevenbond1410 Hi im sorry what was this in regards to again?
@@Yuaaaur the ones in the link look different. Looks like you have to take the wheel off and drop the forks .