This circuit does not work because it shorts the power supply when button is pushed for OFF. A very shoddy design that should not have been made public :(
O circuito é funcional , mas com uma falha grave para desligar o relé que está comandando a carga , o relé 2 fecha curto na alimentação fazendo com que a chave de pressão normalmente aberta vai durar pouco tendo os seus contatos comprometidos em pouco tempo de uso.
you need a third relay, triggered by the NO pin of relay two to open circuit the supply of relay one. but by doing it this way, the switch needs it's own supply so it's power supply doesn't get cut by relay 3
please share diagram for dc load switching using relay.. like i want to install in car. where i press push button to on low beam headlight and on pressing again it provide current to high beam. plz help
Опять неправильная схемв,может быть нужно по цепи питания поставить мощный низкоомный резистор-он предотвратит появление короткого замыкания по цепи питания.
@@circuitspedia I live in a remote area where electricity sometimes goes out. Whenever black out happens, the water supply becomes cloudy. To help my pre-filter, I want to install an auto-flush whenever the electricity returns. I thought of connecting a relay to a NC solenoid valve. I do not know the difference of a one-shot to a one-shot trailing edge. 😅
Please check this push on off video- ruclips.net/video/QTMPZQIIyAo/видео.html
This circuit does not work because it shorts the power supply when button is pushed for OFF. A very shoddy design that should not have been made public :(
I was looking for how to use a momentary switch for turn signals on a motorcycle. This may help!
O circuito é funcional , mas com uma falha grave para desligar o relé que está comandando a carga , o relé 2 fecha curto na alimentação fazendo com que a chave de pressão normalmente aberta vai durar pouco tendo os seus contatos comprometidos em pouco tempo de uso.
you need a third relay, triggered by the NO pin of relay two to open circuit the supply of relay one. but by doing it this way, the switch needs it's own supply so it's power supply doesn't get cut by relay 3
please share diagram for dc load switching using relay.. like i want to install in car. where i press push button to on low beam headlight and on pressing again it provide current to high beam. plz help
I've never seen this circuit schedule before, but my book wasn't here.
Circuit is failed. when SW1 is on, circuit is shorted.
I agree. Add fuse and it will blowout.
@@eddiesuertefelipe1532 Please check this push on off video- ruclips.net/video/QTMPZQIIyAo/видео.html
what the purpose of this video, add some comment so people understand about the circuit
This doesn’t make sense at all. How can the RL1 relay pull its own contact shut? This diagram is wrong.
tem que coloca um diodo entre o +da fonte e o interruptor.
😂😂
FAKE VIDEO
Não fiz deu certo faça deixa falar merda ,Zé ruela procure fazer e fez criticar !
Yes dear this fake video
This is not a fake video
@@circuitspedia It works but you shouldn't do it that way. Shorting is not a good thing.
Yes, but If you keep the botton pressed there will be a short circuit through the NC contact of RL2
Yes, the fuse box must be provided😄
Yes brother आपने बिल्कुल सही कहा Reley 2 मे push आँफ करते समय shortcircuit होगा
Опять неправильная схемв,может быть нужно по цепи питания поставить мощный низкоомный резистор-он предотвратит появление короткого замыкания по цепи питания.
يتعذر الاشتراك لا أعلم .
failed failed failed there is short circuit
Push on off using single button simulation video ruclips.net/video/QTMPZQIIyAo/видео.html
Tem que coloca um diodo entre o + da fonte e o imterruptor pra funciona porque do jeito que ta vai da curto.
Tengan cuidado con ese diseño de push on pus off, tiene una falla y puede ser riesgoso en una fuente de mayor potencia a 2 amperes
Please check this Push on off video - ruclips.net/video/QTMPZQIIyAo/видео.html
Saludos, necesito ayuda para hacer un circuito similar, me podria ayudar ?
This circuit on use ac
Non funziona va in corto, evitate di costruirlo
Hi, can you make a one-shot relay like this? Just wondering if it's the one I needed for my project.
Yes I can
Please tell me details about the function you want.
@@circuitspedia I live in a remote area where electricity sometimes goes out. Whenever black out happens, the water supply becomes cloudy. To help my pre-filter, I want to install an auto-flush whenever the electricity returns. I thought of connecting a relay to a NC solenoid valve. I do not know the difference of a one-shot to a one-shot trailing edge. 😅
Short circuit , not working
Try this another ckt, 100% working ruclips.net/video/QTMPZQIIyAo/видео.html
This is not a fake video