Oh they will fail all right, to me that looks like water got into the hub oil and rusted them badly, then driven and things really went for crap. Wouldn't be much longer and that outer bearing would fail and the wheel would lean over/wobble and the brake drum would be riding on the brake shoe and some interesting steering handling to say the least !.
As a former driver, and driver only, I noticed two (well three things) that if I were to be assigned to that bus in the first 4 minutes of this video that I would have demanded another charter coach and refused that one: 1) lug nut covers. Don't do it. They hide multiple sins. 2) the wrong stud size for the attached rims. Change the rims, change the bolts! 3) obscured hub oil caps. You cannot see what is happening inside the hub if it is obscured. Don't do it! On my daily pre trip there were a bunch of things on our checklist but the things that were always included were rust stripes on the lug nuts. That is a loose lug nut or something worse. Two, if the lugs don't fit, then you must reject! Three if you can't see the oil, then a hot bearing will absolutely ruin everyone's day! I'll put up with 3 pounds of air loss a minute, but that is the law. If I take that coach out of the yard and the brakes feel like mush, then it gets dropped right back in the yard.
i am a commercial truck driver myself and i noticed no sight for the oil level in the hub. i once had the sight break on a hub and i had it replaced immediately. im a local milk hauler so i wasnt too far from the shop at that stop. i periodically look at the truck any time i am stopped. if i can hear air hissing or something doesnt look right, i have it corrected. yes i look at things before i leave, sometimes you can pick up a nail or a screw at a farm that wasnt in the tire before you left. it's an on road / off road type of job things happen. i formerly drove dump truck and i once picked up a valve from an engine at an old steel plant that was recycling old metal. that was the weirdest thing i have ever seen in a tire, an engine valve. i reported it to the company i worked for at the time and they replaced the tire on-site. it was a steer tire, if that went unnoticed that would have been bad.
@@BusGreaseMonkey Indeed That WAS so years ago now if it isn't broken Don't fix it, if you look for problems you are going to find them. So much for scheduled maintenance wait until it goes bang, penny wise and pounds foolish.
I have never before seen any bearings in this condition, the fact that they were on a vehicle of this size and weight category that ooerated on public roads is concerning. Excellent episode, subscribed.
I have been a mechanic on buses for 29 years. Retired and became an inspector on buses with a corporation company name of wsp. I love your videos and wow.What a fine?My head goes off to you.God bless
It amazes me just how many bus owners don't have the knowledge or the effort to do the necessary maintenance on this equipment they own and drive on our highways with us. Not only risking their own lives but ours also. I sure hope you stress to them the importance of regular maintenance checks and how if they cant afford them they shouldn't be driving them.
I’m a truck driver and I will do a walk around and touch wheel hubs on any trailer that I’m not familiar with. Any bad bearings, low oil, or dragging brakes will usually make the hub be warmer than the others. You usually have 15-20 minutes while refueling. Low tires and mating dual will sometimes be warmer also. It’s a good time to check lights too.
Sense I started watching and learning this channel, I give these piles of JUNK wide berth when sharing the roadways. Yeah, thinking 50% of them are dangerous. But, they, look pretty.
That wheel bearing reminds me of one of my highway tractors I bought used years back and from a company who had it from new and they were known to do a fair job of maintaining their equipment. I brought the truck to an alignment shop right after I bought it as I knew it needed some work with the way the tires had wear and it pulled to the right ( needed the caster tweaked ). Well turned out one of the outer wheel bearings was failing as the mechanic felt a bit of looseness and pulled the hub and the rollers poured out of the outer bearing as the cage had failed, a few of those bearing rollers looked like square key stock.
I dont spend a hundred grand a year on my bus but I do take it in yearly for a good check out. This year I had to replace the slack adjusters. Prevost sent different ones so we also had to replace the brake cans. Found a worn out bag on the tag axle and replaced that too. Other minor items that could have gotten worse. A bit of money gives a lot of peace of mind.
im a truck driver, my knowledge of busses is extremely limited. by a tag, do you mean a 3rd rear axle.... like a drop axle. i stumbled upon this channel.
I worked on a trailer once and noted metallic oil in a hub. Somebody had put the fasteners in the cap while working on it at some point and they put it back on full of lock washers...
It's amazing how durable those bearings are, just imagine how those look that fail while in use. I have heard mixed reviews about Prevost, does this indicate poor construction as well as neglect? I watched a video of a guy who had to rebuild his differential on the side of the road. He had managed to get to a rest area, and spent a few days there. Makes me proud of my coach.
All these failures are exactly the same part numbers as other bus brands. Possibly more weight by like 10-15% on them could make a difference but not many variables in the equation
So many vehicles are serviced according to how many miles they do, with the attitude of "it doesn't need it, if it hasn't gone anywhere." And this seems to be the result.
After seeing what you found so far, one has to wonder what ugliness might be in the engine due to lack of not only oil changes but lack of coolant changes. Had the interior been in top notch condition is one thing but with that rating below a zero, and the diff more than likely needing a reman third member and all wheel bearings probably need replaced, etc etc etc, brake pots I'd say, compressor, air drier ... and ... and .. and !. Is it really worth the funds to bring it back to its former glory. Sadly from what I understand if one expects to stay at some campgrounds, they turn older RV's away so no matter how nice an older unit is some places will turn a person down flat.
Here in Quebec, we have MANDATORY yearly inspections for all commercial fleet vehicles. All heavy vehicles have to comply to it, or they get pulled out of the road.
Do you buy all your bearing and seal at the parts store or from a bearing dealer if your going to parts stores check the bearing dealers expand the number of bearing you use and you will be surprise at the different in price
I just tow a little 17’ Casita travel trailer behind a Chevy Colorado and always assume that these million dollar coaches have the very best in maintenance and upkeep. I’ll keep my distance from them in the future…
As a commercial truck driver, there are two kinds of vehicles to avoid as much as possible: RV's , and rental trucks. Not so much from lack of maintenance, but because their drivers usually have no clue, or skills necessary to handle them under emergency situations. (For some, it's a challenge to stay in a lane on the expressway)
Hey there I'm a 30 plus years as a heavy truck mechanic and don't ever remember seeing the washer that goes up against the bearing threaded. So is it safe to say that you set the preload with it instead of the traditional inner and outer jamb nuts. Could it possibly be that way because it's a coach and they do things differently. We all now coaches are 24v so that's different and I'm sure that there are alot of things done definitely. Ya I just stumbled across this video and knew that I just had to take a look Ty for putting this this type of thing so others can see if they choose to. I'm definitely going to check out your channel 👍 🇨🇦
Watching this channel (I’m a big fan) makes me avoid bus campers on the highways. Seems most of them come into the shop in this condition - ready to lose a wheel or their brakes. Crazy. People get into this “hobby” similar to boating…seems like a good idea, so let’s buy one and just drive it around without understanding how to treat it or maintain it. Good for your business I suppose.
It amazes me that people drive these virtual death traps! Now I’m wary any time a motor coach is near me on the road! They might look great but the mechanicals are not readily visible!
Nasty looking assembly from the wheel studs in. Yes, I've seen worse bearings on cars and pickups and a large 5th wheel RV I bought new but on a commercial vehicle - never. Scary to think some bus owners don't (wont?) do regularly scheduled maintenance
With all of these RUclipss I have watched here I think if I had one of these coach conversions that I would have the wheel stubs and bolts replaced at every tire changes.
I am a trailer mechanic for a leasing company. I am so glad I don’t have to take public transportation or get on any bus after seeing this. I thought they would have better maintenance programs since it’s carrying people. I maintain a fleet of 500 trailers and I may have seen that a handful of times. We’re not carrying passengers though.
It would be great to someday see a video possibly called "The True Cost of Owning and Maintaining RV's and Bus Conversions". This would be aimed at current owners and potential future buyers of this large equipment of what is required to keep in proper repair as well as expected maintenance and inspections to keep equipment in safe working condition. And as you and I both know and you stated in this video, equipment which is parked for long periods needs as much if not more attention than one rolling down the highway on a regular basis for various reasons. It is not wise to purchase or own this type of equipment if it will only get used two or three times a year. As for me, I'm doing good since moving to Tennessee two years ago. I switched to a new dump truck company in Franklin 2-1/2 months ago and they are very good to me. So glad not owning and working on my own trucking equipment anymore, those days are now in my past. Maybe some day we'll meet again as I live 20-miles south of you. I assume Tyler is still down here somewhere?
@@BusGreaseMonkey - Oh that ain't no lie. That was how I met Tyler on one of my breakdowns. While I was living in Crawfordsville, I almost bought a Crown tandem axle bus with manual transmission from a SoCal school corp in the 20-teens, and a couple years before that a 1960's GMC Fishbowl transit bus used in Hollywood movies that was in storage in Perris, Calif and now I'm glad I didn't buy either. Both had Detroit Diesels and at the time I had the cash to get both but truth was, they would've nickle and dimed me to death, then who knew I'd sell my business and move south in 2022. That was the best move I've ever made and much happier now but you are the one who give me the idea.
Just curious Scott, you ever try to use your little borescope to peer into the axle housing through the fill hole to get a look at the ring and pinion? Or is it not possible?
I owneded and repaired a small fleet,eet of coaches in the uk for 52 years, if you dont maintain them this is what you get,leaving a bus standing for long periods is not a good idea!
The outer front bearing was about to fully desintegrate and inner would have gone soon after as a large bus either pulls off road with severe wobble or even lose the wheel and crash the bus.
The biggest problem is with bean counters, we don’t need to replace that, make it work! I quit over owners not wanting to do preventative maintenance. If my name is on the state safty sticker, it gets fixed
After over 31 years driving trucks (heavy-haul, windmill blades and now oilfield winch trucks in North Dakota), thisss is why I have come to hate the big coaches, rv's and 5th-wheel campers on the road these days. They should be held to higher standards of inspection and driving just like the big trucks and what we're seeing in this video is a prime example of why. If it wasn't so dangerous, I would have laughed at those bearings! Wow... Chills down the spine... I guess the "entitled" class can get away with murder, though... smh
I wouldn’t call them entitled class. But there are no education or experience requirements required to get behind the wheel of these 30-60,000 lb vehicles and that is scary to me
im a truck driver but i have never worked in the shop. that bearing looked bad. dont those bearing have a sight clear window so you can see if they are lubricated. commercial trucks do
Looking at the heavy rust on the suspension would make me suspect all of the suspension / driveline / rotating parts. Way to much time spent on the bad wheel bearings though, one look and they are done, don't need to even spin them, the damage on one roller makes them bad - set em aside and move on :) This bus defiantly should never have been on the road in its condition.
The gear oil is just nasty stew soup for sure. What is the company name and location of the business BUS repair tech ???? I tip my hat to your for working with abused equipment. This milage is just unbelievable for a bus. I bet trying to find one today with the milage on the clock is just impossible. Look forward to more videos Sir. Good luck and peace too. vf 😀😀😀😀
Probably either got water in the hub and rusted at some point or oil leaked out the cap and it got hot. Looked like a somewhat new cap on it so I bet someone was in there recently
What does it take to get those bearings to fail completely? Is it even possible?
Funny you should ask… check out this in our shorts channel ruclips.net/user/shortsyGkru0AeRIE?si=LZw7PbGPbdDRAM1P
Oh they will fail all right, to me that looks like water got into the hub oil and rusted them badly, then driven and things really went for crap. Wouldn't be much longer and that outer bearing would fail and the wheel would lean over/wobble and the brake drum would be riding on the brake shoe and some interesting steering handling to say the least !.
Probably got millions of miles what do you expect😢😮
@@richardortiz8704 says only just under 88K on it looks like an rv conversion or tour bus
Everything fails sometime. Wasn't that far away. Who signed off the last inspection. That much stuff doesn't wear out in a year.
As a former driver, and driver only, I noticed two (well three things) that if I were to be assigned to that bus in the first 4 minutes of this video that I would have demanded another charter coach and refused that one: 1) lug nut covers. Don't do it. They hide multiple sins. 2) the wrong stud size for the attached rims. Change the rims, change the bolts! 3) obscured hub oil caps. You cannot see what is happening inside the hub if it is obscured. Don't do it! On my daily pre trip there were a bunch of things on our checklist but the things that were always included were rust stripes on the lug nuts. That is a loose lug nut or something worse. Two, if the lugs don't fit, then you must reject! Three if you can't see the oil, then a hot bearing will absolutely ruin everyone's day! I'll put up with 3 pounds of air loss a minute, but that is the law. If I take that coach out of the yard and the brakes feel like mush, then it gets dropped right back in the yard.
A walk around can give you a lot of confidence
@@BusGreaseMonkey large pipe for wiggle test and flashlight for inspection. :)
i am a commercial truck driver myself and i noticed no sight for the oil level in the hub. i once had the sight break on a hub and i had it replaced immediately. im a local milk hauler so i wasnt too far from the shop at that stop. i periodically look at the truck any time i am stopped. if i can hear air hissing or something doesnt look right, i have it corrected. yes i look at things before i leave, sometimes you can pick up a nail or a screw at a farm that wasnt in the tire before you left. it's an on road / off road type of job things happen. i formerly drove dump truck and i once picked up a valve from an engine at an old steel plant that was recycling old metal. that was the weirdest thing i have ever seen in a tire, an engine valve. i reported it to the company i worked for at the time and they replaced the tire on-site. it was a steer tire, if that went unnoticed that would have been bad.
L No
Years ago as a heavy duty, fleet tech we used to say maintenance doesn’t cost, it pays.
Yes
@@BusGreaseMonkey Indeed That WAS so years ago now if it isn't broken Don't fix it, if you look for problems you are going to find them. So much for scheduled maintenance wait until it goes bang, penny wise and pounds foolish.
The moment I saw those stripped wheel studs I thought, its only going to get worse from here....those wheel bearings were something else!
Yes the hits keep on coming
Thank you Scott @BusGreaseMonkey
All private coaches and/or RV's over a certain weight, size, and number of axles should be required to get yearly DOT inspections.
In nearly every country they are inspected, in some ways USA is a third world country.
Over 26k imo
I have never before seen any bearings in this condition, the fact that they were on a vehicle of this size and weight category that ooerated on public roads is concerning.
Excellent episode, subscribed.
I have been a mechanic on buses for 29 years. Retired and became an inspector on buses with a corporation company name of wsp. I love your videos and wow.What a fine?My head goes off to you.God bless
A modest proposal: start a “wall of shame” to display the most memorable horrors removed from customer projects.
I did that with failures from bad to 0 service damage .in AZ
I have a collection
Top gear style hill climb time board 👍
I Revise my comment from last vid on this bus CHA-CHING CHA-CHING AND CHA-CHING 😮😮😮 😅
It amazes me just how many bus owners don't have the knowledge or the effort to do the necessary maintenance on this equipment they own and drive on our highways with us. Not only risking their own lives but ours also. I sure hope you stress to them the importance of regular maintenance checks and how if they cant afford them they shouldn't be driving them.
Most buses you see here are new purchases and they come here right away.
Yes, you don't lose that much oil without knowing you have a leak. If you know you have a leak you top up the oil.
Scott and crew are a shining light in a sea of bus maintenance DARKNESS.
Driving down the hwy at night this bus might have looked like it had red LED lights under it from the glowing red hot parts ;)
I’m a truck driver and I will do a walk around and touch wheel hubs on any trailer that I’m not familiar with. Any bad bearings, low oil, or dragging brakes will usually make the hub be warmer than the others. You usually have 15-20 minutes while refueling. Low tires and mating dual will sometimes be warmer also. It’s a good time to check lights too.
Sense I started watching and learning this channel, I give these piles of JUNK wide berth when sharing the roadways. Yeah, thinking 50% of them are dangerous. But, they, look pretty.
It’s not a lie…
"Is this a good bus?", says the buyer. "Hell yes. You can drive her 'till the wheels fall off!".
Driven hard, put away
wet, scheduled maintenance deferred and ignored.
Sold off when it still looked good.
Caveat Emptor!
Put away dry (no oil) ;)
@@BusGreaseMonkey Yes, total lack! We bought one like that once..parted it out and made a little profit.
That wheel bearing reminds me of one of my highway tractors I bought used years back and from a company who had it from new and they were known to do a fair job of maintaining their equipment. I brought the truck to an alignment shop right after I bought it as I knew it needed some work with the way the tires had wear and it pulled to the right ( needed the caster tweaked ). Well turned out one of the outer wheel bearings was failing as the mechanic felt a bit of looseness and pulled the hub and the rollers poured out of the outer bearing as the cage had failed, a few of those bearing rollers looked like square key stock.
wow, that's bad. really bad
You know it's bad when even Scott is shit shocked
I expected bad but not that bad.
I dont spend a hundred grand a year on my bus but I do take it in yearly for a good check out. This year I had to replace the slack adjusters. Prevost sent different ones so we also had to replace the brake cans. Found a worn out bag on the tag axle and replaced that too. Other minor items that could have gotten worse. A bit of money gives a lot of peace of mind.
im a truck driver, my knowledge of busses is extremely limited. by a tag, do you mean a 3rd rear axle.... like a drop axle. i stumbled upon this channel.
@@andrewdonohue1853 Yes its the unpowered third axle that we can raise for tight corners. It helps hold the weight and gives better handling.
@@andrewdonohue1853same concept as a tag axle on a dump truck, helps carry the extra weight of a full bus
I was very surprised to see the interior of that bus, it looks beautiful on the outside looks are definitely deceiving on this one
I have never seen a wheel bearing THAT BAD that did not cause catastrophic failure! Thanks for what you do, and for showing us!
I think that’s the worst one still in the cage i have seen.
I worked on a trailer once and noted metallic oil in a hub. Somebody had put the fasteners in the cap while working on it at some point and they put it back on full of lock washers...
Note to self to never put little bits in the cap ;)
That's what happens when someone smokes weed on the job
Judging by the wear and damage , I'd say the odometer has been clocked over...
There's no way it's only done 87000 miles...
It's amazing how durable those bearings are, just imagine how those look that fail while in use. I have heard mixed reviews about Prevost, does this indicate poor construction as well as neglect? I watched a video of a guy who had to rebuild his differential on the side of the road. He had managed to get to a rest area, and spent a few days there. Makes me proud of my coach.
All these failures are exactly the same part numbers as other bus brands. Possibly more weight by like 10-15% on them could make a difference but not many variables in the equation
So many vehicles are serviced according to how many miles they do, with the attitude of "it doesn't need it, if it hasn't gone anywhere." And this seems to be the result.
People always ignore the “or # months” in the maintenance intervals
I love watching the work you guys do, admiring from Tasmania, Au.
I am surprised that that wheel was still turning. By the looks of those bearings that should have been frozen.
It was very close to that b
After seeing what you found so far, one has to wonder what ugliness might be in the engine due to lack of not only oil changes but lack of coolant changes. Had the interior been in top notch condition is one thing but with that rating below a zero, and the diff more than likely needing a reman third member and all wheel bearings probably need replaced, etc etc etc, brake pots I'd say, compressor, air drier ... and ... and .. and !. Is it really worth the funds to bring it back to its former glory. Sadly from what I understand if one expects to stay at some campgrounds, they turn older RV's away so no matter how nice an older unit is some places will turn a person down flat.
Yet again Scott saving lives out there.
Wow! That’s some bearing!!
Incredible 70mph and a vibration
Probably the worst I’ve seen!
Save that bearing and use it as a display for future customers.
All I can say is Wow. Safe travels. Ken.
Impressive components on the brink of devastation
Here in Quebec, we have MANDATORY yearly inspections for all commercial fleet vehicles. All heavy vehicles have to comply to it, or they get pulled out of the road.
This was close to making the news for a major crash.
Some very dangerous things happen on this beautiful looking bus
Those long-distance/tour busses are some of the coolest vehicles on the road!!! It takes a special kind of person to drive those things!!!
"Maintenance is overrated" said the owner.
Give him credit for scheduling it in for an inspection
That close up of the chewed up rollers and race was epic worn-porn! Even worse than it sounded from the outside...😮
Worn out to the max
The wheel and the bearing... that is all that I knew what any of that was..... you're an expert
Do you buy all your bearing and seal at the parts store or from a bearing dealer if your going to parts stores check the bearing dealers expand the number of bearing you use and you will be surprise at the different in price
Parts store
It's amazing just how much engineering goes in to these rv's.
I've seen smoother roads than that front bearing. Wow!
That bearing was a bomb and a very short fuse was already lit 🔥
You unquestionably saved a lot of lives by making those repairs.
@darrenstafford7492 there were signs of a problem. I will do a video on looking for the subtle signs
@@BusGreaseMonkeyThat would be great information for those who own a bus,to know what to look for
@@BusGreaseMonkey Also do one on pre-trip checks and another on regular maintenance. Would be invaluable.
What happens to this bus if the customer can not pay for a complete rear axle ?????
I would guess he would sell it.
I just tow a little 17’ Casita travel trailer behind a Chevy Colorado and always assume that these million dollar coaches have the very best in maintenance and upkeep. I’ll keep my distance from them in the future…
As a commercial truck driver, there are two kinds of vehicles to avoid as much as possible:
RV's , and rental trucks. Not so much from lack of maintenance, but because their drivers usually have no clue, or skills necessary to handle them under emergency situations. (For some, it's a challenge to stay in a lane on the expressway)
As a retired touring musician, we had some great busses and some very scary ones.
just rolled in. bus edition. just missin spray foam everywhere
To me, it appears that 'if it moves' it needs to be repaired or replaced. Wow, what a moving 'death trap'.
I looks so nice and has low mileage… ;)
That is the worst bearing I have ever seen.
She was ready to blow!
That's some of the worst spalling I've seen on a bearing.
Almost unbelievable that it was still spinning
Hey there I'm a 30 plus years as a heavy truck mechanic and don't ever remember seeing the washer that goes up against the bearing threaded. So is it safe to say that you set the preload with it instead of the traditional inner and outer jamb nuts. Could it possibly be that way because it's a coach and they do things differently. We all now coaches are 24v so that's different and I'm sure that there are alot of things done definitely. Ya I just stumbled across this video and knew that I just had to take a look
Ty for putting this this type of thing so others can see if they choose to. I'm definitely going to check out your channel 👍 🇨🇦
Now those dashcam videos make more sense, when I see big bus tires flying off, now I know why.
Oil where it shouldn't be, no oil where it should be.
Watching this channel (I’m a big fan) makes me avoid bus campers on the highways. Seems most of them come into the shop in this condition - ready to lose a wheel or their brakes. Crazy. People get into this “hobby” similar to boating…seems like a good idea, so let’s buy one and just drive it around without understanding how to treat it or maintain it. Good for your business I suppose.
It amazes me that people drive these virtual death traps! Now I’m wary any time a motor coach is near me on the road! They might look great but the mechanicals are not readily visible!
They are equally amazed when they find out the condition of what they drove in on.
Nasty looking assembly from the wheel studs in. Yes, I've seen worse bearings on cars and pickups and a large 5th wheel RV I bought new but on a commercial vehicle - never. Scary to think some bus owners don't (wont?) do regularly scheduled maintenance
With all of these RUclipss I have watched here I think if I had one of these coach conversions that I would have the wheel stubs and bolts replaced at every tire changes.
I always assumed Prevost was a premium brand. How do they rate among the others and what is currently the top?
They are premium price but all the components are basically the same as other brands. Same axles, hubs, bearings, engines, etc.
WOW, that is a lot of damage. It would have caused major problems had you not had it serviced. WOW.
Greatest couch builders though❤ Prevost
Raised a front axle years ago on a 2 ton truck. Noisy wheel bearing. Wheel fell off, outside bearing hailed out.
I am a trailer mechanic for a leasing company. I am so glad I don’t have to take public transportation or get on any bus after seeing this. I thought they would have better maintenance programs since it’s carrying people. I maintain a fleet of 500 trailers and I may have seen that a handful of times. We’re not carrying passengers though.
It would be great to someday see a video possibly called "The True Cost of Owning and Maintaining RV's and Bus Conversions". This would be aimed at current owners and potential future buyers of this large equipment of what is required to keep in proper repair as well as expected maintenance and inspections to keep equipment in safe working condition. And as you and I both know and you stated in this video, equipment which is parked for long periods needs as much if not more attention than one rolling down the highway on a regular basis for various reasons. It is not wise to purchase or own this type of equipment if it will only get used two or three times a year. As for me, I'm doing good since moving to Tennessee two years ago. I switched to a new dump truck company in Franklin 2-1/2 months ago and they are very good to me. So glad not owning and working on my own trucking equipment anymore, those days are now in my past. Maybe some day we'll meet again as I live 20-miles south of you. I assume Tyler is still down here somewhere?
“If you own a big bus you probably have something very small in your pants… Yep a very small wallet thanks to your big ol bus.” - Bus Grease Monkey
@@BusGreaseMonkey - Oh that ain't no lie. That was how I met Tyler on one of my breakdowns. While I was living in Crawfordsville, I almost bought a Crown tandem axle bus with manual transmission from a SoCal school corp in the 20-teens, and a couple years before that a 1960's GMC Fishbowl transit bus used in Hollywood movies that was in storage in Perris, Calif and now I'm glad I didn't buy either. Both had Detroit Diesels and at the time I had the cash to get both but truth was, they would've nickle and dimed me to death, then who knew I'd sell my business and move south in 2022. That was the best move I've ever made and much happier now but you are the one who give me the idea.
Just curious Scott, you ever try to use your little borescope to peer into the axle housing through the fill hole to get a look at the ring and pinion? Or is it not possible?
Wow!, that is some bad bearings!
Holey stripped threads Batman!
Case Carborising bearings kept the front wheel on.
Some folks shouldn't own a bus.
He did schedule it for an inspection before doing any of the interior work first.
At least the owner is biting the bullet with these repairs first.
That bus is the vehicular version of "Room 1408" just on the wheel studs alone. Geez!
Im too afraid to watch horror movies, i see enough scary stuff at work ;)
Another 10k bill. Scott will make it right.
If the rear end is bad you are at least 10k to low on that estimate
yeah, on a 5k bus.
Eh, those bearings will polish out and gear oil is highly over rated ;) Thanks Scott for all you do trying to keep us safe on the road!
The fact these bearings, etc held together is a testament to how over-engineered these vehicles are…thank God!!!
I pay warranty so I’m covered, I keep ur with tune up, tire n check for rust n do pre checks before leaving I feel like a trucker 👌
Hear the roar of those bearings!
They were “wheel barleyngs”
You paid extra for the holes in the bearings.LOL😂
That's the worst roller bearing I've ever seen.
ruclips.net/user/shortsyGkru0AeRIE?si=LZw7PbGPbdDRAM1P look at these
repack those bearing good as new lol good work!!
"a wheel and a prayer"
Yikes!
Definition of parts at the “end of life” worn out
firewoodfred says "it's very unfortunate that the innards of that bus don't look like the outside" !!!
Someday it will. He wanted to get the mechanicals sorted out before working on the cosmetic interior sparkle
I owneded and repaired a small fleet,eet of coaches in the uk for 52 years, if you dont maintain them this is what you get,leaving a bus standing for long periods is not a good idea!
Wow, these are really rough.
It was a contest between the front bearing and the rear end to see which locks up first.
Dang! That was educational 👍😎✊
So does that fuck up the inside of the hub? Or is the bearing a softer material thus the wear component?
That is some burnt gear oil! Do you guys have a service that comes and gets all your old oil or do you have to take some place ever so often?
We take it to our local dump where they collect it for recycling
The outer front bearing was about to fully desintegrate and inner would have gone soon after as a large bus either pulls off road with severe wobble or even lose the wheel and crash the bus.
The biggest problem is with bean counters, we don’t need to replace that, make it work! I quit over owners not wanting to do preventative maintenance. If my name is on the state safty sticker, it gets fixed
After over 31 years driving trucks (heavy-haul, windmill blades and now oilfield winch trucks in North Dakota), thisss is why I have come to hate the big coaches, rv's and 5th-wheel campers on the road these days. They should be held to higher standards of inspection and driving just like the big trucks and what we're seeing in this video is a prime example of why.
If it wasn't so dangerous, I would have laughed at those bearings! Wow... Chills down the spine... I guess the "entitled" class can get away with murder, though... smh
I wouldn’t call them entitled class. But there are no education or experience requirements required to get behind the wheel of these 30-60,000 lb vehicles and that is scary to me
I knew when you drained the oil from the hub seeing the light shimmer off the oil there was big problems ahead
im a truck driver but i have never worked in the shop. that bearing looked bad. dont those bearing have a sight clear window so you can see if they are lubricated. commercial trucks do
Thanks for the video.
You are welcome!
Looking at the heavy rust on the suspension would make me suspect all of the suspension / driveline / rotating parts. Way to much time spent on the bad wheel bearings though, one look and they are done, don't need to even spin them, the damage on one roller makes them bad - set em aside and move on :) This bus defiantly should never have been on the road in its condition.
The gear oil is just nasty stew soup for sure. What is the company name and location of the business BUS repair tech ???? I tip my hat to your for working with abused equipment.
This milage is just unbelievable for a bus. I bet trying to find one today with the milage on the clock is just impossible. Look forward to more videos Sir. Good luck and peace too. vf 😀😀😀😀
Those wheel studs explain why my rental Hyundai ate a front wheel off a semi. At 75mph.
Been there ... bearing failure began with "rust pocking " .
Cheers mate🇦🇺👍
Could you possibly say how expensive to fix things in this video? Maybe others. I am thinking about getting a used RV.
Never seen roller bearings with that kind of failure. Hardening failure during manufacture?
Probably either got water in the hub and rusted at some point or oil leaked out the cap and it got hot. Looked like a somewhat new cap on it so I bet someone was in there recently
I'm wondering why you were using a1/4" socket/extension - then I realized, it's just the size of the tire that makes it look like that. Damn.
That bearings had the biscuit 😊😊😊
What happened to the marketplace bus?
I have not had time to check if it is still available or not.
Thanks for the video
I haven't been watching as often as I was? When and where has your son moved on too? Cheers Mark
A bit over a year ago he moved back to Indiana to start a new career outside of wrenching
Makes me glad there's no smell-o-vision
People must be greatfull of fixing this issue, WoW would be a desastreuze situation when kept on the road.