and its crazy with all the rust pitting on the outside that inside of the gun while nasty them parts cleaned up with zero pitting like it was packed in a grease on the inside.... almost like it was just covered in clay and left to rust for awhile not found dug up in a river bed.
I'll admit it; I've always preferred revolvers over semi-automatics because revolvers have "fewer moving parts." But this video showed that there's A LOT more going in a revolver than meets the eye. And, it showed why good quality revolvers are so expensive.
What they usually mean when they say fewer moving parts is fewer EXPOSED moving parts. In my experience, people who say that are usually not experienced gunsmiths, but experienced shooters, so they don't know as much about what's in a handgun as they do about what's on it. DA revolvers usually have a trigger, a cylinder, a latch button, a hammer, and an ejector rod: about 5 parts that, if messed with or not navigated properly, can make the gun experience failure. A typical 1911 has a trigger, a slide, a thumb safety, a grip safety, a hammer, a removable magazine, a slide release/lock and a moving barrel, which is on a swinging link and exposes itself when fired in order for the gun to eject a casing and feed a new round. The 1911 was the US standard for semi autos until the 80s, so when people are referring to semi autos as having a lot of moving parts, they're likely referring to that platform of handgun. In an emergency, safeties can sometimes trip up startled shooters, and whether or not the slide has been racked ahead of time or the round was chambered properly also caused people some issues that the revolver circumnavigated with its external simplicity. Nowadays, there are semi autos with no exposed hammers or thumb/grip safeties, as well as more reliable feeding and extraction systems, which even 1911 platforms benefit from. There are more differences internally, of course, but that's beside the point. Both are uniquely reliable platforms now, and everything depends on what your intended use is. While things not being exposed make them less likely to be subjected to the elements or mishandling, it also means that, if something does interfere with them, you have to take the gun apart to fix it. Most revolvers need at least a screw driver to get at faulty parts. Most semi autos don't need a tool at all to get to what is likely to fail. It's also important to remember that more parts = more complicated = more likely to fail is a complete fallacy that is not universally true from an engineering standpoint. Yes, you shouldn't make things unnecessarily complicated, but a well designed machine, if it has more parts, likely utilizes those parts for a more effective and reliable result. In a computer, they often have cooling fan/vent systems that prevent the computer from breaking via overheating. The computer literally wouldn't be able to function very long without it, yet it consists of additional parts. Same with guns, Smith and Wesson used to have the firing pin that ignited the primers as part of the hammer itself. This actually led to a severe number of failures, according to S&W armorers, who would constantly repair these guns. They redesigned the firing pin separately from the hammer, now housed inside the frame of the gun, and now they no longer have near as many hammer/pin involved failures they have to correct, despite using more parts in the design.
I once repaired the trigger assembly on a revolver & let me tell you it was a bit of a mofo job, it was like I needed 3 hands all at once to complete the task ! 😂
if you think about it, it's simple, the center is the hammer: raising it, you rotate the cylinder, you block it by training the chamber and barrel, and you move the trigger back into the firing position. in double action you move the opposite, the trigger raises the hammer, which does as described before. the only thing apart is the L-shaped bar which prevents the firing pin from reaching the trigger in the event of an accident. a very ingenious system of levers and pins
This gun was intentionally put into a caustic solution and dried out to make this video. It was a controlled solution . Look at the springs and workings they're shiny and in near perfect condition. No pitting , even the engraving everywhere is near perfect.
@@burthoppy I like restoration videos because I love doing restoration. It gives me ideas to my projects. But when people stage it just to get views ....its sad.
@@austin7530 yes I did . I can create the same effect by spraying caustic liquid upon it. But with the severity of corrosion on the outer while the small intricate nomenclature like the springs were unaffected would allow a reasonable suspicion of a staged event. No doubt the motive would be to trigger views to a platform that gives financial benefits for such views. And yet it's just my opinion.
This is a great video! I think it would be even more interesting if you started with the original gun and showed what you did to it before cleaning it up again.
Well said. Obviously just covered it in some sort of concrete or something. How come those tiny springs survived without any corrosion and the threads and pins were all usable?
i do restoration work on armaments ,must say this is a good instructive video,,,,, but for the life of me he makes it look soooo easy,,,,,,,,, rusty screws n leavers bolts ,,, dont work that easy fr me,,,, i use a impact screwdriver even then heads of slot cross screw heads burr and endup having to precise drill them out ,, bu its all worth while in the end,,,,Ed
Tremendous job restoring this one. Brass drift pins and plastic end hammers won't mar the metal upon disassembly. This one was pretty much ravaged by rust and corrosion, but I still winced while watching it being knocked apart.😮
You didn't notice he was using a metal hammer to at first trying to open the cylinder, then all of a sudden we see the plastic end being used? Did you also notice that every screw was removed with no problem?
First, he is the one who ruined it in the first place. He removed every screw without problem, and it's coated in a layer of some shit he likely left it in for a month or three. Second, he's a hack. These aren't proper gunsmith tools.
Mr., I am impressed. First with your ability. Next, with your willingness to do this project. And third, seeing the parts of that pistol that were eaten away by rust as they were, you still (safely) fired that good old Smith and Wesson. GOOD JOB! 😎👍👍👍
Did you actually see THAT gun fire? I didn't! I saw him throw some (ONE) round into a chamber. Then he claimed the camera "overheated". I was born at night, but it wasn't last night!
S&W never plated hammers or triggers. They were always case hardened. Absolutely amazing that the internal parts and the extractor mechanism were in the condition that they were considering the damage to the outside. This one must have been dragged out of a river after being there for a good while.
There was no way I thought that pistol would ever fire again! Impressive to say the least, great job. The actual finished product looks pretty cool too. I'm not sure how safe it is but the fact that is works and fires at all is amazing.
I am ALWAYS absolutely amazed at what you do for these forgotten relics. I enjoy watching watch (timepiece) restorations too and there's really no difference. Precision work is fascinating to watch. Anybody can swing a ball-peen but you know exactly how & where to do it! Thanks again Rustic. Best, Tod in Vagas. :)
Nice work. Impressive. I have a couple of pistols that went through a fire several years ago. Kept them in oil over the years, so they're in relatively good shape (compared to the stuff you've been working on). Is there a way to contact you with some pictures and a quote for restoration? Thx
Amazing how you restored that old 38 special handgun to working order. I thought it was too far gone to be restored but you managed to restore it so that it can fire. It also looks much better than before. Excellent work.
My first thought was it had been battered and deep fried; like someone got drunk and thought they were making onion rings. The next day, “Honey, hand me some aspirin… and have you seen my .38?!?”
Who cares if it’s artificially rusted or what ever its an “ASMR” video going from dirty to clean yall keep watching his videos either way!! Yall keep giving him his flowers by watching then hating… find other shit to do rather than being negative all the time. Its his hobby its his choice to put the videos up. Hes not pointing no gun at your head saying watch my videos or die. Yall need to grow tf up for real!!
So much fun to watch! Thank you so much for firing it from a rig. It gave me a lot of peace of mind knowing it wasn't going to blow up in your hand! 😆 Again, great video!
I watched the whole restoration but I'm still skeptical about how the barrel was able to fire a bullet? That whole pistol was covered in corrosive matter, how was it that the barrel was so easily cleared without much effort? Also, the springs, shouldn't the springs be worthless after all of the corrosion? Just wondering .
The barrel is still able to fire because the inside isn't as pitted as the outside of it. Even with lots of pitting barrels are still capable of firing but will just lose accuracy. As for clearing it, I actually cleared it off camera because of how much of a pain it was. I had to use a hammer and screw driver to get most of the rust out. The springs are all still in good condition because they were protected by being inside of the gun. If you look at the hammer it is very pitted everywhere except for where it was inside of the gun. The outside will always rust and pit much more than the inside.
Dude, weld the chambers in that gun and cut the firing pin. There is a hole in one of the chambers on the cylinder. Take it out of action so that no one has an accident with it.
Развлечения
"Where do you find these guns?"
"I start with a perfectly serviceable gun, then I encase it in concrete for 6 months."
The suspension of disbelief is so real with these channels
Qe tontería pensar así solo disfruta no denigres
I just dont now but i like tho see them@@jonathanbias4506
It's hard for me to imagine how those wooden handles rusted...😂😂
that even caking of "rust" all over everything had to be quite a challenge (to create)
and its crazy with all the rust pitting on the outside that inside of the gun while nasty them parts cleaned up with zero pitting like it was packed in a grease on the inside.... almost like it was just covered in clay and left to rust for awhile not found dug up in a river bed.
this is absolutely staged
and why has part of the handle been digitally pixelated at 2:15
Looks like it was battered and fried. Lol
Good restoration of a pistol covered in brown plaster.
Why would the grips have the same color oxidation. Odd
Mom's gonna be SUPER pissed about her slow cooker.
This channel and couple others greatest skill is getting these guns into these ridiculous conditions in the first place.
No seas ridículo eso lo harías tu y por eso piensas asi
Solo disfruta y deja el drama
I would love to know the circumstances behind how it got in that condition.
My guess is it slept with the fishes, along with the bodies of the souls it took 😅
@@unnamed715😂😂😂
This idiot destroys them all himself. You think he just happens to find a bunch of rusted guns?
@@zeekwolfe6251 What do you mean?
They are drowning them in acid that causes intense rusting very fast and burying them. All these youtubers are doing it for easy restoration videos.
Evaporust on the handles. He must be in some alternate reality where wood rusts. 😂😂😂
The stuff can be used for other things....like a flat head screwdriver is meant for screws but can be used as a chisel
So can someone tell me, how all the fine wire springs were in such good condition?
They are made of rust proof materials
The whole thing is a scam
Это просто контент , искусственно состариные вещи
Yes, they replaced the springs
@@tonykourounblis1854Your birth was a scam
I'll admit it; I've always preferred revolvers over semi-automatics because revolvers have "fewer moving parts." But this video showed that there's A LOT more going in a revolver than meets the eye. And, it showed why good quality revolvers are so expensive.
FAR more accidents occur with a semi automatic weapon than with a single action revolver !.
Double action
@@ThurgoodJenkinz
I stand corrected,,yes, double action 👍🏼
What they usually mean when they say fewer moving parts is fewer EXPOSED moving parts. In my experience, people who say that are usually not experienced gunsmiths, but experienced shooters, so they don't know as much about what's in a handgun as they do about what's on it.
DA revolvers usually have a trigger, a cylinder, a latch button, a hammer, and an ejector rod: about 5 parts that, if messed with or not navigated properly, can make the gun experience failure. A typical 1911 has a trigger, a slide, a thumb safety, a grip safety, a hammer, a removable magazine, a slide release/lock and a moving barrel, which is on a swinging link and exposes itself when fired in order for the gun to eject a casing and feed a new round. The 1911 was the US standard for semi autos until the 80s, so when people are referring to semi autos as having a lot of moving parts, they're likely referring to that platform of handgun. In an emergency, safeties can sometimes trip up startled shooters, and whether or not the slide has been racked ahead of time or the round was chambered properly also caused people some issues that the revolver circumnavigated with its external simplicity. Nowadays, there are semi autos with no exposed hammers or thumb/grip safeties, as well as more reliable feeding and extraction systems, which even 1911 platforms benefit from. There are more differences internally, of course, but that's beside the point. Both are uniquely reliable platforms now, and everything depends on what your intended use is.
While things not being exposed make them less likely to be subjected to the elements or mishandling, it also means that, if something does interfere with them, you have to take the gun apart to fix it. Most revolvers need at least a screw driver to get at faulty parts. Most semi autos don't need a tool at all to get to what is likely to fail. It's also important to remember that more parts = more complicated = more likely to fail is a complete fallacy that is not universally true from an engineering standpoint. Yes, you shouldn't make things unnecessarily complicated, but a well designed machine, if it has more parts, likely utilizes those parts for a more effective and reliable result. In a computer, they often have cooling fan/vent systems that prevent the computer from breaking via overheating. The computer literally wouldn't be able to function very long without it, yet it consists of additional parts. Same with guns, Smith and Wesson used to have the firing pin that ignited the primers as part of the hammer itself. This actually led to a severe number of failures, according to S&W armorers, who would constantly repair these guns. They redesigned the firing pin separately from the hammer, now housed inside the frame of the gun, and now they no longer have near as many hammer/pin involved failures they have to correct, despite using more parts in the design.
I was mesmerised from start to finish...
I didn’t know revolvers had so many parts. I have a greater respect for them seeing this gun restored
Not every gun can be like the Sten Gun with a total of 47 parts, only 4 of which that really moved.
I once repaired the trigger assembly on a revolver & let me tell you it was a bit of a mofo job, it was like I needed 3 hands all at once to complete the task ! 😂
I'm nervous for this guy on the reassembly 😮 SO many parts!
if you think about it, it's simple, the center is the hammer: raising it, you rotate the cylinder, you block it by training the chamber and barrel, and you move the trigger back into the firing position. in double action you move the opposite, the trigger raises the hammer, which does as described before. the only thing apart is the L-shaped bar which prevents the firing pin from reaching the trigger in the event of an accident. a very ingenious system of levers and pins
No lo puedo creer, que genio! Te felicito man, un trabajo perfecto, y no me esperaba que dispares. El mejor fimal .
This gun was intentionally put into a caustic solution and dried out to make this video. It was a controlled solution . Look at the springs and workings they're shiny and in near perfect condition. No pitting , even the engraving everywhere is near perfect.
I see this also.
@@burthoppy I like restoration videos because I love doing restoration. It gives me ideas to my projects. But when people stage it just to get views ....its sad.
No pitting? Ur joking right… did you even watch the whole video???
@@austin7530 yes I did . I can create the same effect by spraying caustic liquid upon it. But with the severity of corrosion on the outer while the small intricate nomenclature like the springs were unaffected would allow a reasonable suspicion of a staged event. No doubt the motive would be to trigger views to a platform that gives financial benefits for such views.
And yet it's just my opinion.
@@Mountain_Paladin the screws are opened easily.
I know that wasnt rust on the handles because they are wooden. So why use Vaporust?
That looked like someone had dropped the gun in plaster.
Stunningly great restoration. Remember that guns don´t kill people! People kills people!!!
It is simply amazing that a revolver has that many parts.
it is a Smith and Wesson. T he insides are modular so there are not very many parts. A Ruger has even less.
Wonder how they make the things grow with molds to simulate rust and plaque.
Now that is how you restore thank you sir.
The human mind and the human hand are truly amazing machines.
This is a great video! I think it would be even more interesting if you started with the original gun and showed what you did to it before cleaning it up again.
Well said. Obviously just covered it in some sort of concrete or something. How come those tiny springs survived without any corrosion and the threads and pins were all usable?
Personally, I like when my wood grips develops layers of "rust"
@@jimjam4082 oh yes, one of life’s greatest mysteries is rusty wood. I’ve heard of ironwood but I don’t think that rusts anyway 🤣
@@nomis3045 they are made from Rust proof materials.
I agree I claim bs
Fried in the Colonel’s secret blend of 11 herbs and spices.
😂😂😂😂
This looks like if Mr Peanut was packing heat! Got himself a peanut gat!!
Great restore of this revolver, reminds me of my grandpappy
Wow very nice!
Why would wooden handles be covered in rust?
That’s clearly not rust
Not rust. Caked on sediment.
Revolvers are definitely underrated.
Love this!! I hope I’m able to watch the whole video without falling asleep 😂😂
How coiuld it have so much rust and still have springs?
Пружины из более качественной легированой стали.
I find it eerie to think about how this gun is probably someone’s secret from long ago. Great work!
Nah, it's artificially reliced
The semi automatic was a nice to watch restoration, i hope it is going to a museum 😢
a soak in hot /soapy water could not have hurt
gotta love the US Army green brush
i do restoration work on armaments ,must say this is a good instructive video,,,,, but for the life of me he makes it look soooo easy,,,,,,,,, rusty screws n leavers bolts ,,,
dont work that easy fr me,,,, i use a impact screwdriver even then heads of slot cross screw heads burr and endup having to precise drill them out ,, bu its all worth while in the end,,,,Ed
The spring that came out if the bullet chamber looked damn good. 🤔
how in the world did that gun get such a uniform layer of clay all over it? And why did you have to use rust remover on wood?🤔
Must have been ironwood.
Restroring things that are rusty and beat up videos are satisfying asf to watch
Молодцы ребята такие шедевры создаете здоровья вам
Превосходная работа! Мастеру респект!
Tremendous job restoring this one. Brass drift pins and plastic end hammers won't mar the metal upon disassembly. This one was pretty much ravaged by rust and corrosion, but I still winced while watching it being knocked apart.😮
Amen, I winced as well. Too much prying also, there are better ways.
You didn't notice he was using a metal hammer to at first trying to open the cylinder, then all of a sudden we see the plastic end being used? Did you also notice that every screw was removed with no problem?
@@davidbrewster5904 clever editing
First, he is the one who ruined it in the first place. He removed every screw without problem, and it's coated in a layer of some shit he likely left it in for a month or three. Second, he's a hack. These aren't proper gunsmith tools.
@@ShotgunDart Guy is using a blacksmith's hammer and plastic Dixie cups lol.
For a .38 Special, you hold on loosely, but don’t let go. 🎶
You have made something unbelievable!
amazing how there seems to be rust on the WOODEN grip
ok
Maybe behind the scenes Marty had Doc use his Deloreons Tri-Flux Capacitor to remove that unique “wood rust”!
Might be ironwood lolol
Not rust
I think it's more amazing that you dont know what rust looks like😂😂😂
Mr., I am impressed. First with your ability. Next, with your willingness to do this project. And third, seeing the parts of that pistol that were eaten away by rust as they were, you still (safely) fired that good old Smith and Wesson. GOOD JOB! 😎👍👍👍
Yeah, I didn’t think it was capable of actually firing..glad everything worked
Did you actually see THAT gun fire? I didn't! I saw him throw some (ONE) round into a chamber. Then he claimed the camera "overheated". I was born at night, but it wasn't last night!
You might want to see a couple other posts before raving.
Literally the first thing that popped in my head when I saw it: “Southern Fried Smith & Wesson”.
It's on my list of must have revolvers
Rust on the WOODEN handle, Kinda strange…
Rust spreads you know… rust can be on almost any, along with mold and other things.
S&W never plated hammers or triggers. They were always case hardened. Absolutely amazing that the internal parts and the extractor mechanism were in the condition that they were considering the damage to the outside. This one must have been dragged out of a river after being there for a good while.
Makes me wonder why it was in the river 😂
@@geneb5482you know exactly why lol
Wrong. They hard chrome plated a ton of hammers and triggers.
Thrown in lagoon after murderous person murder people with it.
@@gmac8852 nah, this guy 100% rusts everything himself.
Its absolutely amazing!!! You are cool!👏👏👏
Thanks for test firing it . 👍
How did this gun get into this condition? What's all that yellow stuff? Maybe there is and interesting story here.
Concrete mixed with mustard? I think this is cluck bait. He took a working gun, messed it up, then cleaned it.
Police may be looking for that thing. 😉
that was the first thing I was thinking of too....he found someone's hidden evidence
The fact it still fires with no hickups is amazing
Great job dude !
There was no way I thought that pistol would ever fire again! Impressive to say the least, great job. The actual finished product looks pretty cool too. I'm not sure how safe it is but the fact that is works and fires at all is amazing.
When are we getting a hand reveal???
Never seen a hand restoration, wonder how it’s done
Someone's got a hand fetish
Onlyhands
@@largeboseheadphone6494 wow
Putting that puzzle of a gun back together would probably stress me out. 🤣 Great job! 👏
I had no idea that there were so many parts to 38.
This guy has a lot of patience
Thanks for test firing. I was thinking this one was too far gone to shoot. That wooden vice was a very prudent idea.
I am ALWAYS absolutely amazed at what you do for these forgotten relics. I enjoy watching watch (timepiece) restorations too and there's really no difference. Precision work is fascinating to watch. Anybody can swing a ball-peen but you know exactly how & where to do it! Thanks again Rustic. Best, Tod in Vagas. :)
Gullible much?
The 38 special was my dad's favorite gun.
Hell yeah, swamp gun. Extra poison damage.
Why don't you wash the revolver in distilled water first? This way there is a high probability that you will break something on it!
Great workmanship and great knowledge of the gun itself. Im impressed with the outcome. Thank you
That’s sooo cool man and it shoots,that’s amazing
Excelente trabajo de Restauración good Yop perfect 🙂👍🏽
Never knew plastic/wooden handles could get so rusty! 😮
Sarcasm if you couldn’t figure it out.
Nice work bellisssssssimo. I love 38 special
Best for personal protection. Very dependable
Kreeen.!! Bro..ini ahli bengkel revolver
That gun was almost petrified. You did a fantastic job on the restoration. From a rock to a working gun. Amazing
I always enjoy and seeing, such a great restoration. 👍👍
Apesar de demorada , eu gosto muito de ver essas restaurações.
Very reliable. 38specials!
Excellent restoration work!! Very enjoyable!!
Nice work. Impressive. I have a couple of pistols that went through a fire several years ago. Kept them in oil over the years, so they're in relatively good shape (compared to the stuff you've been working on). Is there a way to contact you with some pictures and a quote for restoration? Thx
And yet more beating on it metal to metal with screw drivers and punches and steel hammers - more awesomeness. 😱😱
Even though it must be so satisfying to chip away like this I can imagine how much fun you’d have with a vapour blaster
From how it looked before the restoration and how it looked after is a pretty phenomenal transformation. Well done buddy. Very well done.
Watching from Marikina City, Philippines
Amazing just to watch....
Amazing how you restored that old 38 special handgun to working order. I thought it was too far gone to be restored but you managed to restore it so that it can fire. It also looks much better than before. Excellent work.
buena que hiciste esa pistola está cálida
Right!! No half-smart person would even attempt to fire a round through that gun!
@@JoseVeliz-st7zzhi y hi
hello Ruth, sure to authorise will be taken care of your own
@davidbrewster5904 I sure Wouldn't
My first thought was it had been battered and deep fried; like someone got drunk and thought they were making onion rings. The next day, “Honey, hand me some aspirin… and have you seen my .38?!?”
Who cares if it’s artificially rusted or what ever its an “ASMR” video going from dirty to clean yall keep watching his videos either way!! Yall keep giving him his flowers by watching then hating… find other shit to do rather than being negative all the time. Its his hobby its his choice to put the videos up. Hes not pointing no gun at your head saying watch my videos or die. Yall need to grow tf up for real!!
You find it if you find it then you’re really good at finding things❤
Truly amazing! But I can't help but wonder how the gun got into such bad shape originally.
saw a comment saying they destroy them on purpose for content, so idk man, that thought is always in the back of my mind now that I watch these videos
It was used for murder and dumped in lagoon but was found by restoration man to be restored and used again. Endless cycle of murder machines.
Fraudulent 😠
A baseball bat is a murder machine if you want it to be. Anything can be, even your hands. @@gmac8852
i can't even keep my apartment clean and this individual is out here breathing new life into relics. Incredible workmanship
Nice job would like to see you use brass tools especially your sledge hammer ❤
So much fun to watch! Thank you so much for firing it from a rig. It gave me a lot of peace of mind knowing it wasn't going to blow up in your hand! 😆 Again, great video!
Depending on where that was found, I wonder how many bodies it has on it. Great restoration.
Lil' pistol gots lots of parts. Awesome cleaning.
I watched the whole restoration but I'm still skeptical about how the barrel was able to fire a bullet? That whole pistol was covered in corrosive matter, how was it that the barrel was so easily cleared without much effort? Also, the springs, shouldn't the springs be worthless after all of the corrosion? Just wondering .
Spare parts are edited into the videos
The barrel is still able to fire because the inside isn't as pitted as the outside of it. Even with lots of pitting barrels are still capable of firing but will just lose accuracy.
As for clearing it, I actually cleared it off camera because of how much of a pain it was. I had to use a hammer and screw driver to get most of the rust out.
The springs are all still in good condition because they were protected by being inside of the gun. If you look at the hammer it is very pitted everywhere except for where it was inside of the gun. The outside will always rust and pit much more than the inside.
Nice restoration! Amazing how perfect the internal parts were! Too bad about the pitting on the outside.
Lo hace con tanta delicadeza y eso me relaja, saludos
When you started loading the gun I was shocked. 😆
But I knew he knew what he was doing! :)
I would have liked to see some of the surface pitting removed, but thats just my preference. Awesome restoration! 😎
maybe harden filler,,,, milliput i use "two part filler" can be drilled tapped when cured ,,,, Edwin J
Looks like plaster to me
Admirable y satisfactirio desde el comienzo hasta el final. gran profesional . Gracias por compartir .lo felicitó.
Engraving by mother nature.
Oh wow I wonder how the wood hasn’t rotted off! Old rusty guns don’t look artificially rusted, like it’s been covered on purpose…
Dude, weld the chambers in that gun and cut the firing pin. There is a hole in one of the chambers on the cylinder. Take it out of action so that no one has an accident with it.
he could replace the cylinder
Bet this man single handedly keeps his arts and crafts store alive
Melhor vídeo pra assistir parabéns 🎉