Getting same issue where one side is only getting ip addresses. i noticed you set ip address of both routers to 192.168.1.1 which would cause an ip conflict as they are on the same subnet. On server you put 192.168.1.1 as default gateway. which would explain why only one side receives an ip address and not the other. please advise.
it's important to known which Fa port was connected in each router to acomplish a correct configuration... this video is too quick and totally forgets the idea of show how to do it...
Great video. Thanks. I have a question. Is it me or you are assigning the same exact IP address 192.168.1.1 to 2 interfaces on 2 different routers? Isn't a problem?
I carefully followed what you have done. It successfully gave IP Addresses. Then after a while. It fails then says DHCP Failed. APIPA. Case 2: When I close packet tracer then open it again. Only 1 side is given IP addresses.
this is not right, i am frustrated about this one, created 3 new projects and it was still the same. NOTE: FOLLOWED EVERY STEPS BUT STILL ONLY ONE ROUTER GETS THE IP FROM DHCP SERVER.
You can use more than one helper address per interface. When a router forwards these address assignment/parameter requests, it acts as a DHCP relay agent.
Getting same issue where one side is only getting ip addresses. i noticed you set ip address of both routers to 192.168.1.1 which would cause an ip conflict as they are on the same subnet. On server you put 192.168.1.1 as default gateway. which would explain why only one side receives an ip address and not the other. please advise.
it's important to known which Fa port was connected in each router to acomplish a correct configuration... this video is too quick and totally forgets the idea of show how to do it...
Great video. Thanks. I have a question. Is it me or you are assigning the same exact IP address 192.168.1.1 to 2 interfaces on 2 different routers? Isn't a problem?
i understand there is only one default gateway on dhcp server. Then to connect 2 routers they need to share the same ip address
Seems like you're picking random addresses and I can't understand how you choose them. I'd be glad if you explained this.
why did yo assign the same ip address 192.168.1.1 on two different routers? shouldn't it be different?
I carefully followed what you have done. It successfully gave IP Addresses. Then after a while. It fails then says DHCP Failed. APIPA.
Case 2:
When I close packet tracer then open it again. Only 1 side is given IP addresses.
he forgot to show that he turned on the dns and gave it the ip 192.168.1.10
@@MyBruger could you plz explain it more specifically?
how to turn on the dns? thanks a lot.
@@MyBruger Can you explain it please ?
@@emrebinnaz3687 he should go on the server then DNS on. but still not working
@@sunitabnsl It is not important for me anymore :)
this is not right, i am frustrated about this one, created 3 new projects and it was still the same. NOTE: FOLLOWED EVERY STEPS BUT STILL ONLY ONE ROUTER GETS THE IP FROM DHCP SERVER.
Dude just used same IP address in both router, no rip or static routing just gotta check if it works
So can i ping the 1st router's clients to the 2nd router's clients?
in your videos which version cisco packet tracer you used?
بالتوفيق مسيرة موفقة
why you put 192.168.1.10 as helper address? don't you have to put the default gateway from the dhcp server?
great question
one side DHCP is not working
same ip on both routers. fuck this
What is the written in the iOS command line ???
Turn off and again turn on packet tracer and everywhere APIPA, what i can do?
you should have to save the settings before you turn off. Run this command "copy running-config startup-config"
Dangerous minds Where to enter this command?
example on a router#wr or switch#er
U r a living legend ( if this works )
U r a legend
you are the best ,thx for help
Glad to hear that
i have got ip address to both the sides but ping is not working
It's not working the right one is the only one who got dhcp but the other side is not. I followed all the instruction many times..
johnrey casipong same problem
WHY IS THERE NO AUDIO IN THIS VIDEO?
wonderful tuto, because is where i am, but i want to Know how can i do to connect those two routers
i need an answer thank so much
You guys don't know how to teach anyone. You need to go slow enough where people can follow or else we get NOTHING out of it.
after a while only one of the networks can get DHCP address while other cant. Can you help me figure out why
may be you skip one of the steps.
dangerous topology
hi
I have some problem in this course, can you help me
please show ,, how to prove it connected to other side...
I am getting as DHCP request failed.What to be done ?
Kindly watch video carefully.
i love you man
do you have source code for this lab ?
you're the best thanks!!!
didn't work
I love u, bro
This is a terrible tutorial. No explanation given!
doesnt even work as well
do this with 192.168.130.0 pls
yeah good idea
What did you did at last
You can use more than one helper address per interface. When a router forwards these address assignment/parameter requests, it acts as a DHCP relay agent.
VERY NICE
Thank you
why i can't?
kindly follow all steps carefully.