I just came from KT3406E channel, jesus what a mess this is, they didn't even try to be clean. Don't drain the oil just tip over the engine on the ground without the head and move on with live
@@heavymetalrc7520 Before grinding the valves with a special paste, as he did, it is necessary to give them a profile shape. This is done with a milling cutter. Then the work will be done correctly.
These guys will be repairing Mad Max's car.
Oil from the engine to the ground, that's normal!
Good Job!
Кашу маслом не испортишь!
(сказал тракторист сливая отработку на пшеничное поле)
0:09 где то, у девочки по имени Гретта, случился сердечный приступ...
🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣
А бородатый белый - это официальный представитель Caterpillar в Пакистане.
torque wrench is a mythical creature around these lands
And what about the tolerances? It is clearly seen that the adjustment between crankshaft and connecting rod is H7, I can't stop laughing.
It's like the middle ages with electricity
Oil on the ground keeps the dust down for a cleaner rebuild
I am dreaming of a plasti Gage and a torque Wrench for Xmas
такой ремонт когда гарантия до выезда из гаража.
Does anyone else cringe every time they remove an internal engine part and throw it on the ground?
On it's 6th overhaul in 2 years.
Man, I admire these guy’s ingenuity but doing an engine in those conditions? Jeez, I don’t know.
Good job, but it's better to do it in a clean place.
Yes, you are right
👍👍👍👍
good idea
Прямо пособие - как делать не надо....
👍👍👏👏👌👌
I feel a bit sad watching these videos, knowing they could early make a 10,000hour engine with a bit more cleaning and better tolerances
No concern about groundwater contamination, air pollution, it’s fine. Then blame America for global climate change.
Да всем срать на санкции падшей америки😂
@@turbid0909 Weakness by some not all. Trump will set things right.
@@turbid0909 mojesh konecno i srat, no ot etogo sankcii ebat teba menshe ne stanut.
@@johndemeen5575все приходят с благими намерениями,а уходят с народным гневом😏Трамп не исправит ничего если не станет президентом❗
@@turbid0909. Make sure you vote.
such repairs are under warranty before leaving the garage.
Fără niciun fel de dubiu, sunt buni în ceea fac cu un minimum de unelte și unde au un spațiu cât de mic, sunt de 10.
Water in piston or water in cylinder?🤦
The engine warranty is about 7 minutes or so, right?🤣🤣🤣🤣🤣 has no waste
such repairs are under warranty before leaving the garage.
You've got to be kidding.
I just came from KT3406E channel, jesus what a mess this is, they didn't even try to be clean. Don't drain the oil just tip over the engine on the ground without the head and move on with live
Got a question. What was the ole man doin slammin and spinnin the valves against the head? And what's the white compound he was usin? 10:37
He is perhaps the only one who did his job correctly. not counting the fact that first he had to grind the valves and valve seats.
Valve grounding compound. Well..that's what you're supposed to use. Not sure if he used that.
@@heavymetalrc7520 Before grinding the valves with a special paste, as he did, it is necessary to give them a profile shape. This is done with a milling cutter. Then the work will be done correctly.
About the environment, not heard off.