Got mine from HK. I'm impressed! Was going to diy a quad but wanted to fly asap and not be repairing every crash. I'm sure you can break components on it but takes a bigger beating then a diy build racer. I'm like the limited wires and clean build of the vortex 250.
If I were to switch those props out for KingKong 5040 3Blade props, will the lock nuts that come with the quad work be able with them? if not which lock nuts should I get? And what tool should I use to get them off? Thankyou for the video, Really helpful :)
+Joseph Dawson There are different flight modes. Angle, horizon and acro are what you have available. You can then tune everything to your liking or use the protunes that come pre-installed on the FC.
Hi mark .mi vortex pulls to the left .i have set it up on a level surface about 6 times and still pulls left any sugestions.i need to quet this fix thanks in advance
+HobbyKing Live hi mark .it pulls left on hover .am. in rate mode .or horizon .same thing just is like is motor heavy on mi right side.and the only way to fix this is have mi trim all the way to the right.?i calibrated in clean flight.no motors bent .no bad props.is a brand new quad.thanks for your time.any suggestions.other then change flight settings or pro tunes.cause it does it in all modes .havent tried acro .not good enough.yet;).am aot of suggetions .it works good if i have the trimm all the way to the right..but thas not the right way:(
Hmmm. Do you have any subtrim or regular trim in on the aileron channel? Have you tried doing the channel mapping and setup again? Try a different pro tune also and see if that changes anything/
+Hobbyking live ,hi again no I don't have any trim .but it does copy the command even do I only have the 5 channels on mi channel mapping but mi roll channel was a little short on the bar compared to all other channel commands,and the only way to make it level with all other channels is with mi trim ,I also have the taranis on clean flight channel map.am clue less now ?
+leejulz1 Yes, we ship to the Uk from our intl warehouse and also we have a warehouse located in the UK. However, some products are not stocked in the UK warehouse. I'm going to have to say the Vortex 250 Pro is the better choice. The runner 250 isn't bad, that's for sure, but we've been enjoying the vortex a lot.
thank for reply in just for park use as i have a few drome but want sumthing faster if i waz raceing them vortex wud kill but its just for park use and after xmas il be order 1 as i love my dromes i have
"I'm going to power it on so we can see firsthand"... " so we can see first hand me getting my pinky chopped off cuz I have my props on, but I'm an expert so its ok"
+Pa RC Quad Racers It's essentially RTF minus battery, receiver, & FPV system. You're getting a whole lot for your $500. Easily one of the best 250 racing quads on the market that doesn't require the end user to do any assembly or serious setup.
+Pa RC Quad Racers Not really, if you were to purchase all components individually and assemble them in your own frame you would also be close to the $500 range. Remember this is a semi-premium carbon fiber quad, includes OSD, camera and video transmitter. Don't forget all the R&D that went into this system making it programmable through the OSD!
Got mine from HK. I'm impressed! Was going to diy a quad but wanted to fly asap and not be repairing every crash. I'm sure you can break components on it but takes a bigger beating then a diy build racer. I'm like the limited wires and clean build of the vortex 250.
BONUS FOOTAGE BABY
Very nice step up from the original vortex :D
haha, love the star wars music startup.
Would be nice to see what you're actually doing with your transmitter to set it up ie moving the sticks or toggling Switches
Remove your props when powering up on the bench! Too many people learn that one the hard way.
Will I be able to fly like Metal Danny with this? :)
That OSD setup is briljant :$
+DutchRC Adventures I see you getting one of these bad boys Dutch!
+Discover RC I would like to have (and fly) it for sure mate! ;) There are more things that fit that bill though :D
well... finally! Sweet baby jebus!
I like what you guys did with the monitor. great video. know it's a little late
If I were to switch those props out for KingKong 5040 3Blade props, will the lock nuts that come with the quad work be able with them? if not which lock nuts should I get? And what tool should I use to get them off? Thankyou for the video, Really helpful :)
what's the difference between this one and the blade vortex 250? the green one?
+Elias Treger Green one comes with a spektrum receiver and the red one you put your own receiver.
what should I set my Spektrum transmitter throttle endpoints to?
Do they only have ONE flight mode? Do you have a level mode as well as rate mode or is it only rate?
+Joseph Dawson There are different flight modes. Angle, horizon and acro are what you have available. You can then tune everything to your liking or use the protunes that come pre-installed on the FC.
+HobbyKing Live Didn't see a step in the Rx wizard where you choose the mode switch.
+HobbyKing Live did you skip that step in the video where you setup modes?
Can I fly that Drone with lite radio 2?
Any of you guys recommend this (or the Multistar Vortex 285) for a beginner? If not give me some recommendations.
Hi, would this work with an x8r receiver and a Frsky Taranis X9D Plus 2.4Ghz? I apprecaite any helpfull response.
+K0ji Themaster Yes, however the best receiver for it is the D4R-II
dang in between Clips did you run to the bathroom and shave lol
Hi mark .mi vortex pulls to the left .i have set it up on a level surface about 6 times and still pulls left any sugestions.i need to quet this fix thanks in advance
+haussemann deter Pulls as in rolls left or yaws left? Does it do this in hover or forward flight? Have you tried changing the pro tune?
+HobbyKing Live hi mark .it pulls left on hover .am. in rate mode .or horizon .same thing just is like is motor heavy on mi right side.and the only way to fix this is have mi trim all the way to the right.?i calibrated in clean flight.no motors bent .no bad props.is a brand new quad.thanks for your time.any suggestions.other then change flight settings or pro tunes.cause it does it in all modes .havent tried acro .not good enough.yet;).am aot of suggetions .it works good if i have the trimm all the way to the right..but thas not the right way:(
+HobbyKing Live rolls left.alote.!thanks in advance on working this minor detail with mi new vortex 250.
Hmmm. Do you have any subtrim or regular trim in on the aileron channel? Have you tried doing the channel mapping and setup again?
Try a different pro tune also and see if that changes anything/
+Hobbyking live ,hi again no I don't have any trim .but it does copy the command even do I only have the 5 channels on mi channel mapping but mi roll channel was a little short on the bar compared to all other channel commands,and the only way to make it level with all other channels is with mi trim ,I also have the taranis on clean flight channel map.am clue less now ?
Oh nice looking very nice ;)
hobby king u cudnt help me do u ship to uk and whats beter walkera 250 runer our Vortex 250 Pro
+leejulz1 Yes, we ship to the Uk from our intl warehouse and also we have a warehouse located in the UK. However, some products are not stocked in the UK warehouse.
I'm going to have to say the Vortex 250 Pro is the better choice. The runner 250 isn't bad, that's for sure, but we've been enjoying the vortex a lot.
thank for reply in just for park use as i have a few drome but want sumthing faster if i waz raceing them vortex wud kill but its just for park use and after xmas il be order 1 as i love my dromes i have
+leejulz1 Whatever you order, I bet you'll still have plenty of fun.
haaa thank u
hmm, I see a 1300mAh 4S Turnigy Bolt on there :)
+vzachari Works great even on regular 4s 1300 or 1400.
+HobbyKing Live Of course it does, but the 1300mAh 4S Turnigy bolt is also a new product :)
Nice 😊
"I'm going to power it on so we can see firsthand"... " so we can see first hand me getting my pinky chopped off cuz I have my props on, but I'm an expert so its ok"
$500.00 for a 250 ARF...?
Man a tad bit pricey.
+Pa RC Quad Racers It's essentially RTF minus battery, receiver, & FPV system. You're getting a whole lot for your $500. Easily one of the best 250 racing quads on the market that doesn't require the end user to do any assembly or serious setup.
+Pa RC Quad Racers Not really, if you were to purchase all components individually and assemble them in your own frame you would also be close to the $500 range. Remember this is a semi-premium carbon fiber quad, includes OSD, camera and video transmitter. Don't forget all the R&D that went into this system making it programmable through the OSD!
Again CMOS camera....pfffff
@hobbykingaz
53