I thought only the two side back pieces were the ones removable and not the center back at least that's how it works on the original one, basically he should be able to hold two weapons on his back, you may want to try that
yes, right it turned out like that... I just realized after uploading the video sometime later... but still i can open the pieces on the back and the slot on the hips to... thank you for the reminder
@@Iqbalparepare wait, you can open the 2 slots on the sides on his back?? I have a KO and I'm scared I might break the slots trying to open them, I tried once and they didn't seem to be opening
Its plastic not playdough. Worst case scenario would be warping but even then its just a matter of common sense, as in dip for a few seconds shape and cool repeat if needed. To actually melt that'd require a heat gun, toaster oven or just fire.
easy, The packaging is cheap and seller say this is a bootleg, if you watch review for the original one, you will see many diffrent in articulations or gimmick.
@@returnedtomonkey8886 i think the articulations is good enough for action figure, idont have the original but compare to Spartan Collection this figure have good range of articulation
@@Iqbalparepare A bit late. Ordered it today from aliexpress. If it's a waste of money... well wouldn't be first time I wasted money. Tip: gunpla bootlegs are shiiiiit. Parts broke or were to tight to fit and had to use a lot of super glue. Never making that mistake again.
@@Tokufan-1951yo, if you can see the master chief inside the box, the pelvis "belt" the green part above the legs, under the stomach. It shoud not be one piece, the groin guard should be fixed, the belt arms should have a clear cut on each side of thr groin guard, hope that helps
I think that's an amazing KO, pretty similar to the original but it has some understandable bad details
You can create a hole on the back that can holster a gun
Yes I have also done the same thing
How you do that?
@@williammandang by s screwing using a small screw driver
I thought only the two side back pieces were the ones removable and not the center back at least that's how it works on the original one, basically he should be able to hold two weapons on his back, you may want to try that
yes, right it turned out like that... I just realized after uploading the video sometime later... but still i can open the pieces on the back and the slot on the hips to... thank you for the reminder
@@Iqbalparepare wait, you can open the 2 slots on the sides on his back?? I have a KO and I'm scared I might break the slots trying to open them, I tried once and they didn't seem to be opening
yes its not open in my KO too 😅
@@cheesuschrists try leaving it in hot water for a few mins, not boiling though
@@SageLebron soak the figure in hot water? Idk what if doing that causes the figure to deform as well as the slots still don't open
Not bad,you can customize that figure
The Jazwares are 6.5 not 7.5, even tho, I think the accessories of this figure may work with the Jazwares as well
Yes
Thinkin of purchasing it only for the brute shock rifle
Wouldn't the gun melt putting it on warm water ?
i think not, its fine with warm water.
Just hot
nota boiling
Its plastic not playdough. Worst case scenario would be warping but even then its just a matter of common sense, as in dip for a few seconds shape and cool repeat if needed. To actually melt that'd require a heat gun, toaster oven or just fire.
How can you tell its a knocknoff?
easy, The packaging is cheap and seller say this is a bootleg, if you watch review for the original one, you will see many diffrent in articulations or gimmick.
@@Iqbalparepare are the articulations worse than the original?
@@returnedtomonkey8886 i think the articulations is good enough for action figure, idont have the original but compare to Spartan Collection this figure have good range of articulation
@@Iqbalparepare A bit late. Ordered it today from aliexpress. If it's a waste of money... well wouldn't be first time I wasted money.
Tip: gunpla bootlegs are shiiiiit. Parts broke or were to tight to fit and had to use a lot of super glue. Never making that mistake again.
@@returnedtomonkey8886 i'm buying some gunpla bootleg too. You need more efford to make it good, but yeah it make your finger bleed 🤣
Wait how do you know if it’s a knock off
Is it worth getting this figure? Because the original is so expensive
If you dont mind with the diffrent like moving part in the suit, so yes its worth for Master Chief figure.
Not bad
Just bought one 😁
Itu belakangnya berarti gak bisa dibuka buat holster senjatanya bro?
Abang beli di nogo shop y?
Di rendam brp menit?
bukan, sblm masuk nogo shop sy belinya
Ini direndam air panas warna catnya gak memudar?
ga mudar kok, asal air hangat yah yg panasnya cukup, jangan air mendidih 😅
Yg di blkng itu ga bsa di buka ya, yg buat nyantolin snjta
iya ga bisa 😅
@@Iqbalparepare nyantolin snjt'nya gmna dong om?
ya ga bisa, disimpen tempat lain 🤣
@@Iqbalparepare bangke 🤣
yang aslinya berapaan bang?
jutaaan 😅
This is Heresy, this fake bootleg figure is GOD AWFUL! I hate it, the real figure is infinitely better in every way!
yes definetly... the real figure way more high quality than this.
But the price...
Pun intended??
Probably won't get an answer but is there a way to tell by the box?
@@Tokufan-1951yo, if you can see the master chief inside the box, the pelvis "belt" the green part above the legs, under the stomach. It shoud not be one piece, the groin guard should be fixed, the belt arms should have a clear cut on each side of thr groin guard, hope that helps