First, Thank You! I enjoy watching a master craftsman who enjoys their work and is willing to share their knowledge. I learned a lot from you. Again, Thanks!
I could swear construction is a young man's game but I guess you're the exeption to this rule, lol! Your knowledge, hands on dedication to the remodeling trade -- while teaching the finer details -- is just unbelievable. I don't know how you can do this hardcore work solo and not be burnt out yet! The other video was insane, where you demolitioned that crazy old house's bathroom and tore out the plastered slat walls down to bare bone studs and cast iron pipes ... Like my back and joints freakin hurt just watching! And hats off to the camera lady too, for putting up w the work site dust (w lead asbestos!) in some of these jobs. I hope you had some guys there helping out in between takes, lol. Anyway, my input on this video: I've done some custom shower glass enclosures -- w/o using the metal U channels. I prefer the clean true frameless glass look, and not drilling into tiles, and not seeing soap residual along the metal channel's edge at the bottom. I order and pre-fit the glass panel BEFORE tiling that specific area, and create a natural recessed slot channel (.3" deep or so) for the glass to go into. I can also set the tile first (like in situations w' the tricky tile pattern you have here) then cut out a straight vertical channel in the tiled wall, same width as the glass thickness, w' an angle grinder & quality diamond blade. Both methods give a hidden channel space where you can easily adjust the glass in or out for a precise fit, and to angled positions too if needed, to get a specific custom fit. At the floor and any horizontal sections, the glass simply sits on top of the tile and I just apply silicone sealant in between the two surfaces. I prefer minimal silicone exposure on the inner shower side as it (or any caulk for that matter) will eventually develop discoloration and get moldy w' regular use. Also before caulking I mask tape a straight line both sides of glass and on the floor too, where the excess silicone would ooze out -- so cleaning up is simple, just peeling the tape before the silicone dries. This painter's tape trick also gives a factory-like straight, clean and minimalist looking caulk line.
The glass door was the toping on this bathroom. I do have one issue. However, the plug in my estimation should have been raised to above the sink counter. But I have to say, excellent workmanship 👍 👍
Thanks 😊 took me a second to to understand what you were saying “what plug 😆 “ oh yeah, I hate those things no matter where I put them. Always look out of place 😆
@BathroomRemodelingTeacher ; I usually will put a plug on the side wall if possible and at least a foot above the sink. It's always hard to know just where to place them darn things. I want to thank you for your quality of work. It is truly great to see others that take pride in their work and the detail. It is getting harder and harder to find pride in workmanship, It shows. Keep up the great. work.
Love your videos Steve, you have inspired me to give it a try soon. One question…when you were putting the u channel on the bench you mentioned the importance of not drilling into the wood (if the bench had been framed with wood instead of foam). But then when you installed the u channel on the vertical wall, you showed a clip from a previous video where you installed wooden blocking. Why is it ok to drill into the wooden blocking for the vertical portion of the glass, but not into wooden framing (had the bench been framed with wood)? What’s the difference? Thanks again for such great content and inspiration.
There’s really no way for water to saturate and sit in u-channel on wall. The bench there’s definitely a chance of water getting in. If you fill u-channel fully with silicone, there really isn’t too much to worry about 👍
Would it be wise to consider the shower head when determining the door height? Don't want splash over the glass door. On the bench, cut the glass with the slant?
All the installers are using hi-bond adhesive tape for the bottom track these days, and know better than to screw into the floor especially on a curbless. Stronger than silicone.
Question my shower , tub and vanity master bath needs at min that door. When my Dad built my home everything was hot mopped in the shower. Now 30 yrs later the shower has no issues except the door is trashed. Now I can do this cause I am a contractor ( I kind of messaged you what I do , finish carpentry) . How on earth do you find time to work on your house? I gotta schedule like a month just like I am working two jobs , so I can work my schedule? You seem to be working in the day? Not 3 am
All I can say is you have to prioritize yourself. If you don’t have nice things yourself how can you do it for others. It’ll wear you down over time. Almost like a resentment of sorts. Hard to take criticism or wants from clients when you don’t have it for yourself. Good luck 👍
@ your right ! I hv a list and I do hv a very nice house and now is when those items that scare home owners are up for fixing . Can you guess why I am watching your channel? Tips! And that shower glass door company is gold man! Hey I appreciate your time that you take to teach and help others !
First, Thank You! I enjoy watching a master craftsman who enjoys their work and is willing to share their knowledge. I learned a lot from you. Again, Thanks!
I could swear construction is a young man's game but I guess you're the exeption to this rule, lol! Your knowledge, hands on dedication to the remodeling trade -- while teaching the finer details -- is just unbelievable. I don't know how you can do this hardcore work solo and not be burnt out yet! The other video was insane, where you demolitioned that crazy old house's bathroom and tore out the plastered slat walls down to bare bone studs and cast iron pipes ... Like my back and joints freakin hurt just watching! And hats off to the camera lady too, for putting up w the work site dust (w lead asbestos!) in some of these jobs. I hope you had some guys there helping out in between takes, lol.
Anyway, my input on this video: I've done some custom shower glass enclosures -- w/o using the metal U channels. I prefer the clean true frameless glass look, and not drilling into tiles, and not seeing soap residual along the metal channel's edge at the bottom. I order and pre-fit the glass panel BEFORE tiling that specific area, and create a natural recessed slot channel (.3" deep or so) for the glass to go into. I can also set the tile first (like in situations w' the tricky tile pattern you have here) then cut out a straight vertical channel in the tiled wall, same width as the glass thickness, w' an angle grinder & quality diamond blade. Both methods give a hidden channel space where you can easily adjust the glass in or out for a precise fit, and to angled positions too if needed, to get a specific custom fit. At the floor and any horizontal sections, the glass simply sits on top of the tile and I just apply silicone sealant in between the two surfaces. I prefer minimal silicone exposure on the inner shower side as it (or any caulk for that matter) will eventually develop discoloration and get moldy w' regular use. Also before caulking I mask tape a straight line both sides of glass and on the floor too, where the excess silicone would ooze out -- so cleaning up is simple, just peeling the tape before the silicone dries. This painter's tape trick also gives a factory-like straight, clean and minimalist looking caulk line.
Hi i have read your comment and i do like the idea. I would like to hear how you ‘d water proof on the moveable side of the door. Thanks
Mainly I love how you’re so excited about this.
many thanks from Spain.
Great install! Need to add a couple outtakes at the end to spice it up!! 😅
Awesome video Steve!
Hi could you please share what holding the fixed side if door that it won’t come loose. thank you
The glass door was the toping on this bathroom. I do have one issue. However, the plug in my estimation should have been raised to above the sink counter. But I have to say, excellent workmanship 👍 👍
Thanks 😊 took me a second to to understand what you were saying “what plug 😆 “ oh yeah, I hate those things no matter where I put them. Always look out of place 😆
@BathroomRemodelingTeacher ; I usually will put a plug on the side wall if possible and at least a foot above the sink. It's always hard to know just where to place them darn things. I want to thank you for your quality of work. It is truly great to see others that take pride in their work and the detail. It is getting harder and harder to find pride in workmanship, It shows. Keep up the great. work.
Great video!!!! How much did the door cost or did I miss that part ?
How do you keep the schedule always full? So as not to lack customers?
What sort of anchors and ceramic bit do you recommend?
Great videos! One question though, what stops water from coming through on the hinged side?
Bulb seals if you want to 👍
Love your videos Steve, you have inspired me to give it a try soon.
One question…when you were putting the u channel on the bench you mentioned the importance of not drilling into the wood (if the bench had been framed with wood instead of foam). But then when you installed the u channel on the vertical wall, you showed a clip from a previous video where you installed wooden blocking. Why is it ok to drill into the wooden blocking for the vertical portion of the glass, but not into wooden framing (had the bench been framed with wood)? What’s the difference?
Thanks again for such great content and inspiration.
There’s really no way for water to saturate and sit in u-channel on wall. The bench there’s definitely a chance of water getting in. If you fill u-channel fully with silicone, there really isn’t too much to worry about 👍
Would it be wise to consider the shower head when determining the door height? Don't want splash over the glass door. On the bench, cut the glass with the slant?
Did you have to subtract the thickness of the U channel from your measurements, or do they do that if you order the channel from them?
They take of that but yes, 1/4”
Do they really have free shipping on all orders?
Go to sight and check it out. You’ll get a price at end (free shipping!) bit.ly/3NWdRWm
It says on their website, under $300 is a $25 shipping fee. Over $300 for products that are listed, it is free shipping.
All the installers are using hi-bond adhesive tape for the bottom track these days, and know better than to screw into the floor especially on a curbless. Stronger than silicone.
I would have done 78 inches high since you don't have a curb to raise it up a few inches. 72 from the floor is very low...for taller people.
Question my shower , tub and vanity master bath needs at min that door. When my Dad built my home everything was hot mopped in the shower. Now 30 yrs later the shower has no issues except the door is trashed. Now I can do this cause I am a contractor ( I kind of messaged you what I do , finish carpentry) . How on earth do you find time to work on your house?
I gotta schedule like a month just like I am working two jobs , so I can work my schedule? You seem to be working in the day? Not 3 am
All I can say is you have to prioritize yourself. If you don’t have nice things yourself how can you do it for others. It’ll wear you down over time. Almost like a resentment of sorts. Hard to take criticism or wants from clients when you don’t have it for yourself. Good luck 👍
@ your right ! I hv a list and I do hv a very nice house and now is when those items that scare home owners are up for fixing . Can you guess why I am watching your channel?
Tips! And that shower glass door company is gold man!
Hey I appreciate your time that you take to teach and help others !
Is this sponsored content?