thank you so much 😭 the instructions my module came with were so lazily written and just complete trash. my first try wiring your diagram and my actuator finally works, thank you thank you!
I have an 08 pathfinder. I'm trying to wire in my remote starter. My car has negative door locks. The door lock switch has a one wire communication line that goes to the bcm and the bcm reverses polarity. Can I wire in a 5 wire relay straight to the driver door lock actuator to reverse polarity. And will it affect the operation of the bcm?
Why is it when I connect the alarm module(white and white/black wire) to central lock, the master actuator loses control over slaves but will work on remote, and when i disconnect alarm module, the master actuator controls all slaves. Mine is a positive trigger central lock
HI! Do you know by any chance what sort of central locking system hasa Mitsubishi Shogun Pinin 2005, right hand drive? I cannot figure it out if it's negative/ pozitive or neg-poz trigger. I tried every possible way but it doesn't work... thanks in advance!
Finally I found the wires to connect the lock/unlock (they were on the left hand side pillar. Now I would like to connect the brown from keyless module to hazard lights. I tried to connect the to hazard button on the dash but don't work... any ideas? The plug for this button has 4 cables. 2 with signal, 2 without. The first ones don't trigger when I lock the car from the remote control
boss kahit ba manual n sinar yung lock at tumatakbo sasakyan umiilaw p din flasher? ganun ksi sakin eh kahit nka hazzard ng eenterupt sa flasher pg ng lolock at unlock
All the way negative or positive trigger can use??because look like same..different in negative or positive trigger only..the acctuator wiring just 2 wire use..white and brown..??
you can use either of the two depending the manufacturer, but most of the modules now are negative trigger. Always refer to owner's manual before installation
@@chomytuideas1784 yes..same in video..master slave 5 wire..on the module 2 wire input from the alarm receiver..so use the negative trigger direction rite??so in alarm module setting output for negative trigger only..its true??
Sir sinunod ko ung sa manual ng alarm ko tpos gumagana nmn ung lock at unlock na ung signal wires plng nya nka connect khit di pa nka tap ung negative at positive trigger wires.. ok n kya un na no conection ung negative at positive kc nag lock at unlock sya sa remote pa din
Master actuator have 5 wires in order to give signals to slave actuators. When you lock/unlock the master actuator, slave actuators will also lock/unlock simultaneously
@@chomytuideas1784 thanks for a quick answer so i want to lock or unlock the passenger door from driver door, would u tell me if i need a 5 wire actuator in driver door and 2 wire actuator in passenger door or both doors should have a 5 wires actuator? else i want to lock or unlock both doors with a keyless fog
Bos pag naay central Lock module orange and orange/black No connection? Then brown wire from central lock connect to solid white wire sa keyless entry module or pwdi rasad didto ma connect sa white/black?
Hye sir..in the keyless entry diagram..the module just 1 wire output for signal light..how to connect for left n right..??cant got problem if join together..because i think if joint the left n right wire to 1 wire output from module,if we on turn left signal both side signal turn on to rite???
@@chomytuideas1784 nice sir...u are so good n very kind...tq for your info..i try find the way..i think my mine for headlight output not for signal..if connect to headlight only use 1 wire output..what do you think??is it true??
Brother need a help,.when in install newsecuety system master board lock switch not working, but remote working properly, bt if i again instal my old security all working properly
sir tanong ko lang po.. nag kabit ako ng alarm.. ok naman xa nong kinabit ko tinesting ko.. kinabukasan ginamit ko sasakyan.. habang tumatakbo nag lock xa tapos nag aalarm.. pag unlock ko mga 10seconds mag lock na naman..kahit umaandar sasakyan nag aalarm
@@chomytuideas1784 hindi kuna yun kinabit sir.. kasi wala naman ganun sa sasakyan ko.. isuzu hilander.. ang kinabit ko lang na wire ay sa.. horn,parklight,positive,ground at yong papuntang central lock lang..
salamat po dito. mejo nalilito poko kc daming diagram. ung nabili kopo alarm remote central lock. pansin kopo dipo nagana ung central lock pag nakaconnect sa module. pag manual poko ngunlock sa drivers door, dipo nag a unlock ung ibang mga pinto. nagunlock at lock naman pag sa remote. pero pag wla sa module nagana central lock, kaso di nmn gumana sa remote. salamat po
i mean pag di nakakaconnect ung brown white ng central module sa remote module, gumagana central lock. nagoopen lhat ng pinto pag manual ko inopen ung lock sa drivers door. pero pag nakaconnect ung brown white ng central lock module, magoopen lang ung mga pinto pag napress sa remote.
@@chomytuideas1784 sir tama naman po diagram ko. master actuator nsa drivers door. pag nag lock or unlock ako sa master actuator nagana mga slave actuator pag di nakaconnect ung brown white wire sa alarm remote module . kaso di naman nagana remote lock. kung nakaconnect naman lahat ng features nagana,like auto lock sa break,unlock sa engine off,etc.ganun po ba talaga. or may problema nabili ko. last diagram po sinundan ko. salamat po
Salamat sa diagram boss. Ganyan na ganyan hinahanap ko. May tanong lang ako boss paano kapag mag lalagay ako ng 5 pin switch sa loob saan ko itatap ang wires?
Boss bat yung sakin dalawa lng wires ng actuator sa driver's side... Pero control naman nya lahat. Kaso ngayon minsan gumagana minsan hindi gumagana at may sound sya pag gumana. Any idea po?
@@markgamalog293 mostly pag ganyan boss meron na yang central lock na stock pero walang remote. Kaya dinagdagan lang ng actuator na connected sa alarm module
@@chomytuideas1784 okay... but there are 2 wires one is blue and one is Green, When i use buzzer in green wire with ground wire then the buzzer works while lock the car and when I use buzzer in blue wire with ground wire then the buzzer works while unlocking the car. May be these wires are going to Door gun, Can we use buzzer in this wires?
@@chomytuideas1784 Hello sir, Yung ganyan po na keyless entry wala po syang siren feature. pero mabasa ko po sa manual. Iprogram sya sa power window feature? Paano po yun
Dude, thank you VERY MUCH! I looked at several videos and none was explained and showing each and every wire like your video. Much love.
Great to hear! Thanks bro...
Very clearly done, explained each wire and all connections in detail. Thanks.
Thank you sir
I have been searching for this exact diagram for hours. Thank you so much!!
you're welcome
thank you so much 😭 the instructions my module came with were so lazily written and just complete trash. my first try wiring your diagram and my actuator finally works, thank you thank you!
The best diagram i ever seen. Very clear. Greetings from Indonesia
Thank you sir!
Thanks mate exactly the video I was looking for , had me quite stumped for a while before I came across it
Bought an alarm system diagram sucked but I found yours makes way more sense thank you!
thank you, sir!
Thank you very much for the diagram all 3 scenarios
Thank you this is what I was looking for!
Excuse me, do you know how to synchronize the control with the central box?
Thanks
👍
I have an 08 pathfinder. I'm trying to wire in my remote starter. My car has negative door locks. The door lock switch has a one wire communication line that goes to the bcm and the bcm reverses polarity. Can I wire in a 5 wire relay straight to the driver door lock actuator to reverse polarity. And will it affect the operation of the bcm?
how can I add switches to the locks? locking and unlocking via switch on door panel following this diagram ?
Why is it when I connect the alarm module(white and white/black wire) to central lock, the master actuator loses control over slaves but will work on remote, and when i disconnect alarm module, the master actuator controls all slaves. Mine is a positive trigger central lock
Did you solve this problem?
Honda provides positive triger or negative trigger
HI! Do you know by any chance what sort of central locking system hasa Mitsubishi Shogun Pinin 2005, right hand drive? I cannot figure it out if it's negative/ pozitive or neg-poz trigger.
I tried every possible way but it doesn't work... thanks in advance!
sir, try checking the existing switch beside your door by using a tester
Finally I found the wires to connect the lock/unlock (they were on the left hand side pillar. Now I would like to connect the brown from keyless module to hazard lights. I tried to connect the to hazard button on the dash but don't work... any ideas? The plug for this button has 4 cables. 2 with signal, 2 without. The first ones don't trigger when I lock the car from the remote control
La mera nata Gracias Brou!
boss kahit ba manual n sinar yung lock at tumatakbo sasakyan umiilaw p din flasher? ganun ksi sakin eh kahit nka hazzard ng eenterupt sa flasher pg ng lolock at unlock
Thanks a lot. Very clear helped me to install mine.
Hi is there a way to add a central lock to the car alarm/ keyless entry diagram( negative trigger) please?
All the way negative or positive trigger can use??because look like same..different in negative or positive trigger only..the acctuator wiring just 2 wire use..white and brown..??
you can use either of the two depending the manufacturer, but most of the modules now are negative trigger. Always refer to owner's manual before installation
master actuator has 5wires. slave actuator has 2wires(blue/green)
@@chomytuideas1784 yes..same in video..master slave 5 wire..on the module 2 wire input from the alarm receiver..so use the negative trigger direction rite??so in alarm module setting output for negative trigger only..its true??
@@mohamadfauzery yes, 2 wires only (white & brown). you can use negative as trigger output
Very simple and helpful thank you so much
Thank u sir
Is there a way to wire without central lock module? and still use master/slave actuator?
Yes. But you have to use 2 relays as your module. I will upload soon of this method. Stay tuned. Thank you 👍
@@chomytuideas1784 Nice, thank's for the tip!
I need this same thing
Sir sinunod ko ung sa manual ng alarm ko tpos gumagana nmn ung lock at unlock na ung signal wires plng nya nka connect khit di pa nka tap ung negative at positive trigger wires.. ok n kya un na no conection ung negative at positive kc nag lock at unlock sya sa remote pa din
Power windows output for what.. I'm not connected,if i want connect it, where is the power windows output position..?
This diagram is not for power windows...
This video may help you>>>
ruclips.net/video/Bs-axKcXkjw/видео.html
would you tell me what is the function of the Master Actuator/ or why it have 5 wire?
Master actuator have 5 wires in order to give signals to slave actuators. When you lock/unlock the master actuator, slave actuators will also lock/unlock simultaneously
@@chomytuideas1784 thanks for a quick answer so i want to lock or unlock the passenger door from driver door, would u tell me if i need a 5 wire actuator in driver door and 2 wire actuator in passenger door or both doors should have a 5 wires actuator? else i want to lock or unlock both doors with a keyless fog
@@Janetteag only the driver's door should be installed with master actuator. The rest will be slave actuators
thanks again! so any brand that you recommend for those actuator
@@Janetteag any brand will do sir
Signal light tu kita nak sambung dari mana ye.?
Can I have a diagram to wire a 2008 Suzuki apv? Thanks
Can you add the keyless entry with a car that has power locks ?
Yes sir
Can you wire your aftermarket keyless entry into your factory alarm
yes sir
Well done bro
Bos pag naay central Lock module orange and orange/black No connection?
Then brown wire from central lock connect to solid white wire sa keyless entry module or pwdi rasad didto ma connect sa white/black?
Pwde ra boss
@@chomytuideas1784 tnx bos
Hye sir..in the keyless entry diagram..the module just 1 wire output for signal light..how to connect for left n right..??cant got problem if join together..because i think if joint the left n right wire to 1 wire output from module,if we on turn left signal both side signal turn on to rite???
you need to put a rectifier diode(6A10) or (1N4007) each wire for the signal light
@@chomytuideas1784 oow..u got the diagram??
@@mohamadfauzery yes. Watch the the video i uploaded. The brown wire is divided into 2 wires then put a diode each of the wires going to signal light
@@chomytuideas1784 nice sir...u are so good n very kind...tq for your info..i try find the way..i think my mine for headlight output not for signal..if connect to headlight only use 1 wire output..what do you think??is it true??
connecting to headlight is not recommended. The design is for signal light only.
Thank you very much❤
Brother need a help,.when in install newsecuety system master board lock switch not working, but remote working properly, bt if i again instal my old security all working properly
This is the link brother for manual switch lock/unlock
ruclips.net/video/FHtqZRM6nf8/видео.html
Sir ung power window & siren progmram pano mapagana? Ung siren program lang which is ung green wire
what is the difference between positive and negative trigger, can you explain please 🥺
Thanks a lot mate...
I have a new alarm and centrel locking system.Anybody have a wiring diagram for 2 door 2 wire unit.
Boss, paano po mlalaman qng negative trigger o positive trigger ung central lock?
Mantap 👍
Thank you 👍🏽
how to still use master/slave without central lock module?
You have to use relays
@@chomytuideas1784 I have a couple relays but Im not sure how to hook them up
Soon ill make diagrams using relays
@@chomytuideas1784 thank you!
sir tanong ko lang po.. nag kabit ako ng alarm.. ok naman xa nong kinabit ko tinesting ko.. kinabukasan ginamit ko sasakyan.. habang tumatakbo nag lock xa tapos nag aalarm.. pag unlock ko mga 10seconds mag lock na naman..kahit umaandar sasakyan nag aalarm
baka yung wire sa door switch sir mali ang koneksyon
@@chomytuideas1784 hindi kuna yun kinabit sir.. kasi wala naman ganun sa sasakyan ko.. isuzu hilander.. ang kinabit ko lang na wire ay sa.. horn,parklight,positive,ground at yong papuntang central lock lang..
@@reymundnacino7773 hindi kay defective yung nabili mo sir?
@@chomytuideas1784 ok naman xa sir nong kinabit ko.. nagamit kopa xa ng isang araw.. pwd kaya e resset yun sir
@@reymundnacino7773 di ko pa natry kung pwde ba yan ireset sir
please gif me link how to buy keyless entry and central lock 🙏🙏
Full support here from Tampilisan
Salamat mego. Asa man ka dapit sa tampi?
nice...
Boss vios Batman ano kulay trigger Ng central lock ayaw Naman gumana sa test light
Central lock module link???
Nindota kol,., Pushbutton napod kol :) okie kaau. Thanks
maghimo ra ta ana puhon kol
salamat po dito. mejo nalilito poko kc daming diagram. ung nabili kopo alarm remote central lock. pansin kopo dipo nagana ung central lock pag nakaconnect sa module. pag manual poko ngunlock sa drivers door, dipo nag a unlock ung ibang mga pinto. nagunlock at lock naman pag sa remote. pero pag wla sa module nagana central lock, kaso di nmn gumana sa remote. salamat po
i mean pag di nakakaconnect ung brown white ng central module sa remote module, gumagana central lock. nagoopen lhat ng pinto pag manual ko inopen ung lock sa drivers door. pero pag nakaconnect ung brown white ng central lock module, magoopen lang ung mga pinto pag napress sa remote.
sundin mo lang yung last diagram boss. halos lahat ng module ngayon ay negative trigger. bihira nalang yung positive trigger.
Dapat master actuator ang nasa driver side boss para gagana lahat ng slave actuator pag palo ng master actuator
@@chomytuideas1784 sir tama naman po diagram ko. master actuator nsa drivers door. pag nag lock or unlock ako sa master actuator nagana mga slave actuator pag di nakaconnect ung brown white wire sa alarm remote module . kaso di naman nagana remote lock. kung nakaconnect naman lahat ng features nagana,like auto lock sa break,unlock sa engine off,etc.ganun po ba talaga. or may problema nabili ko. last diagram po sinundan ko. salamat po
@@jillsael8306 parang may prob yata sa module pag ganyan boss
How to add lock unlock switch button? For switch 5pins
Manual switch lock/unlock 5pin switch ruclips.net/video/FHtqZRM6nf8/видео.html
Thank you 😉😉😉
😅 salamat po!
you're welcome po
Thank you
I have different color of wires can anyone help me
Thank you boss
Welcome boss
❤❤❤❤
ser mgppalit po ko ng module... 9pin lng po yung orig pro 10pin po yung bgo.. ppno po yun?
Icompare mo lang sir yung mga colors ng wire
magkkaiba po ser..pti 10 po yung wires ng bago... 9 lng po sa stock ser
@@johannsbeleno3232 ganito gawin mo sir. Itest mo yung stock na wires yung mga functions nya.
Salamat sa diagram boss. Ganyan na ganyan hinahanap ko. May tanong lang ako boss paano kapag mag lalagay ako ng 5 pin switch sa loob saan ko itatap ang wires?
Anong ibig mong sabihin sa 5pin switch boss?
@@chomytuideas1784 maglalagay kasi ako switch sa loob ng sasakyan boss para sa door lock. Pano wirings non?
@@jcorpano9405 connect mo sa blue wire boss
Bos Ano yung door negative trigger
yes boss..negative
Boss bat yung sakin dalawa lng wires ng actuator sa driver's side... Pero control naman nya lahat. Kaso ngayon minsan gumagana minsan hindi gumagana at may sound sya pag gumana. Any idea po?
Anu sasakyan nyo boss?
@@chomytuideas1784 Hyundai accent 2017 boss
@@markgamalog293 mostly pag ganyan boss meron na yang central lock na stock pero walang remote. Kaya dinagdagan lang ng actuator na connected sa alarm module
@@chomytuideas1784 pano malalaman pag sira ung actuator boss? Minsan kasi gumagana minsan hindi... Tapos pag gumana naman eh may sound sya
Thanks!
Boss ask ko lng paano malalaman kung positive o negative trigger gagamitin?
Gagamit po kayo ng tester boss para malaman kung positive or negative
Anong pnagkaiba ng mga trigger?
May positive po na trigger. Meron din negative na trigger
San ba nilalagay
which wire is for Buzzer ?
Pink wire
@@chomytuideas1784 There is no any pink wire in my Hyundai Eon Company fitted central locking
if there is none, your module is not compatible for buzzer
@@chomytuideas1784 okay... but there are 2 wires one is blue and one is Green,
When i use buzzer in green wire with ground wire then the buzzer works while lock the car
and
when I use buzzer in blue wire with ground wire then the buzzer works while unlocking the car.
May be these wires are going to Door gun,
Can we use buzzer in this wires?
@@lordof_goodness do not connect the buzzer to those wires. better connect the buzzer to signal light wires using rectifier diode
There's no diagrams only Kurdish videos
Because you did not watch the full video
????
good day sir...direct battery dapat ang pag install ng central lock??
yes sir.para kahit nakaoff yung susi, gagana pa din ang central lock
@@chomytuideas1784 salamat po ng marami idol
ano recommend nyo central lock with remote para sa corollabigbody sir?
@@vhinez01 aventail sir pwde na.or kahit anong brand sir bsta tignan mo muna mga review sa online bago ka bumili sir
slamat po sir..from san fernando pampanga po
Pede actual biss
yes boss. Meron tayong mga actual installationsp. check mo lang mga videos ko. Thanks
@@chomytuideas1784 Hello sir, Yung ganyan po na keyless entry wala po syang siren feature. pero mabasa ko po sa manual. Iprogram sya sa power window feature? Paano po yun
Wala po syang siren sir. Di ko din natry yung sa features nya sa window sir
@@chomytuideas1784 Wala na ibang choice ng wiring sir maliban sa lagyan ng diode yung sa signal
@@chomytuideas1784 Pwede po kaya sya itap sa wire ng central lock?Para pag nag lock unlock natitrigger fin po siren?
Thank you