On the plenum to inlet manifold, it's good practice for anyone doing this to do the end bolts up last as sometimes if you tighten the end ones the tabs can snap off the manifold due to not having much material. Best practice to do all the middle ones first followed be either end last just to be safe this helps it from putting too much tension on the end ones. Hope this helps anyone 🙂
Finger blaster will be proud of you. That MAF code is quite generic I've found as it comes up for a few reasons like boosts leaks too. Could just need your MAF and MAP cleaning with electrical contact cleaner. MAP sensor is easy to access on the cold boost pipe with Headlight off.
You will need some mapping done soon, especially after the exhaust if getting a sport cat. I kept getting that code too, it never came back after putting a dreamscience map on the car with the dreamscience imap
Glad you got that plenum on.what do you think after first drive....i found out mine was split and glued back together 🤔funny that I'm doing my turbosmart actuator this weekend
Hozit boet. You have a boost leak/vacuum line hole somewhere. I had the same code and car went into limp every now and then then.... Have you tried putting off the traction control as soon as you start the car? Does the code then stay away? If yes, you have a hole somewhere. Mine was in the vacuum line on the bottom of the plenum. Had a hole the size of my finger in it. Have a look at all your vacuum lines and do a proper boost leak test. Let me know if you want more info.
Definitely think our innuendos are on the same wave length 😂 ‘small what?’ 😂 at the end of this lockdown you could probably do a whole video on ‘The lockdown transformation - Engine bay’ 😍😍😍 Looking good under the hood haha
It would of been worth getting the polished lower inlet manifold while replacing the plenum. Good old auto specialists do a exchange deal like the carbon dash parts you installed. I'm supposed to be getting a new car (RS3 or AMG) but now I want to keep modding my ST.
I have the red plenum on mine. May have to repaint it though as the paint has started to flake on the bottom left edge. Don’t know why as the rest of it is still mint. And funnily enough i cut myself on the exact same bracket installing mine 😂
did you struggle to get the 8mmbolt in nearest the throttle body? i cant get mine in due to the throttle body allowing only half a hole for the bolt. do i fit the plenum first then refit the throttle body after?
On a cold start how does the car behave? High idle that settles after X amount of seconds, or does it drop straight under 1k. If you have had P0101 for a while It could be your MAF has hit the bullet. When mine died the cold start idle was a give away plus PO101.
Although it looks great it’s pretty unnecessary for the power you are running and the mid range torque gains really are minimal. But it looks class though
I was going to order the rs slam panel but couldn’t see any holder for the bonnet strut - where do you put the bonnet strut with the new rs slam panel?
Block mod is dodgy, I have had the steal liner system from dream science fitted, expensive but far more safe than little bits of metal wedged between the liners. Which is a cheap fix for a possible major issue's in the future. Car looks sweet.
I'm also doing a bonnet latch conversion on my car so that you can pull the bonnet from inside the car simply because there is always a problem with these not working, the white plastic bit comes out the lock so when you put the key in it doesn't work, I have replaced my lock 3 times and it is really hard to get the bonnet open if the lock doesn't work Here is a youtube video on how to do it ruclips.net/video/9NwGBu4cICw/видео.html
On the plenum to inlet manifold, it's good practice for anyone doing this to do the end bolts up last as sometimes if you tighten the end ones the tabs can snap off the manifold due to not having much material. Best practice to do all the middle ones first followed be either end last just to be safe this helps it from putting too much tension on the end ones. Hope this helps anyone 🙂
Your doing so well and over the past few weeks your st sounds so much better
Keep up the good work
its a Plenum not a plenum spacer man :(
03ANO agreed.
Yes boys how are u both doing .
What a difference thats made to the engine bay Tidy :)
Finger blaster will be proud of you. That MAF code is quite generic I've found as it comes up for a few reasons like boosts leaks too. Could just need your MAF and MAP cleaning with electrical contact cleaner. MAP sensor is easy to access on the cold boost pipe with Headlight off.
Great video George & Luke 😊
Very smart
Looks good and improved performance
Cool
Phil in stoke
Anembo plenum with polished trumpets and spacer plate is the BEST all over !!!!
Definitely like that new plenum, it looks so much better and it's shiny =D
Coming together so well. Keep it up lad! Like button slapped 👋
Nice job George, some of those bolts are awkward to get too.
Some very tasty mods you have planned for the future as well.
Awesome video great content. You can see the disappointment on your mans face at the end. It was like he was hoping you were going to propose to him?
Plenum looks so good! Engine bay is looking sexxxaay
Looking good mate keep it up
That looks so much better
The car is Looking well nice now 👍🏻
air mass code is caused by turbulant air hitting the sensor caused by the 90 degree bend at the air filter !air mass sensor needs linear air flow !
I need a plenum too just so expensive, and shipping 😬 looks super clean man keep it up!
What about rs vents?
Inlet manifold or plenum no spacer involved at all
Made a lot of different to the bay will be getting one for mine looks sweet 👍
that codes is the maf sensor (mass airflow sensor) i wud guess
Love the mods on the car also
We out here doing bits!
You will need some mapping done soon, especially after the exhaust if getting a sport cat. I kept getting that code too, it never came back after putting a dreamscience map on the car with the dreamscience imap
It has been live dyno remapped awhile back mate, from past vids
@@DB-dx8xu have you still got your red beast mate, been looking out for you on the roads.
Looks sick!
Looks so tidy 👌👌
Glad you got that plenum on.what do you think after first drive....i found out mine was split and glued back together 🤔funny that I'm doing my turbosmart actuator this weekend
Hozit boet. You have a boost leak/vacuum line hole somewhere. I had the same code and car went into limp every now and then then.... Have you tried putting off the traction control as soon as you start the car? Does the code then stay away? If yes, you have a hole somewhere. Mine was in the vacuum line on the bottom of the plenum. Had a hole the size of my finger in it. Have a look at all your vacuum lines and do a proper boost leak test. Let me know if you want more info.
I have a spare maf sensor if urs is bad?
Definitely think our innuendos are on the same wave length 😂 ‘small what?’ 😂 at the end of this lockdown you could probably do a whole video on ‘The lockdown transformation - Engine bay’ 😍😍😍 Looking good under the hood haha
What do the screws on the engine bay dress up kit screw into please?
It would of been worth getting the polished lower inlet manifold while replacing the plenum. Good old auto specialists do a exchange deal like the carbon dash parts you installed. I'm supposed to be getting a new car (RS3 or AMG) but now I want to keep modding my ST.
Did you notice any power gain?
I got that code too dunno what it is, looking good check out the billet front engine cover on eBay too,
I have the red plenum on mine. May have to repaint it though as the paint has started to flake on the bottom left edge. Don’t know why as the rest of it is still mint. And funnily enough i cut myself on the exact same bracket installing mine 😂
Can you give us a link to the parts that you have installed some of the things I Wana buy
Does it give u anymore power and wot b. H.power gain from it
did you struggle to get the 8mmbolt in nearest the throttle body? i cant get mine in due to the throttle body allowing only half a hole for the bolt. do i fit the plenum first then refit the throttle body after?
MAF sensor may be where you disturbed it reset it and see
I want this plenum so bad 🤤
On a cold start how does the car behave? High idle that settles after X amount of seconds, or does it drop straight under 1k. If you have had P0101 for a while It could be your MAF has hit the bullet. When mine died the cold start idle was a give away plus PO101.
Interesting. You say that
I’ve noticed it for a while yes and the car turns on and drops almost instantly
I’ve never replaced it before so could be possible.
And yes I’ve had the code for ages
You can buy the MAF sensor by itself without spending 100s on the housing and MAF.
Thought you would have liked the other compliment.
Can u send a link for the bolts you used for the plenum to the throttle body plz
Although it looks great it’s pretty unnecessary for the power you are running and the mid range torque gains really are minimal. But it looks class though
Liam mcgrath probably will make sense once block mod and power upgrade is done I reckon.
Who are you thinking of to do the block mod ?
Unsure. Possibly matt Lewis motorsport
Hate tiktok love the car
I was going to order the rs slam panel but couldn’t see any holder for the bonnet strut - where do you put the bonnet strut with the new rs slam panel?
Liam Bell there is actually another holder in the metal slam panel just behind where the original holder in the plastic slam panel was/is.
ST Yusuf ah so it is still secured if i replace the slam panel?
Nice mate. Would be cool to see how much horsepower you gained only with the inlet.
Not worth putting on if your car is under 400bhp
Could you send me a link to the plenum bolts please
www.ebay.co.uk/itm/174196932863 :)
Thank you
I wanna know what exhaust is coming!?! 👀👀👀
Vid goes up this afternoon.
Do you not fancy the RS turbo, injectors / running gear?
Well see what happens down the line pal
Gotta use some Vaseline on those rings man...
Did you forget to re plugin mar air sensor back in
Can some1 please explain to me why the maf needs to be at 2 o clock lol
Block mod is dodgy, I have had the steal liner system from dream science fitted, expensive but far more safe than little bits of metal wedged between the liners. Which is a cheap fix for a possible major issue's in the future. Car looks sweet.
Luke loves a pair of leggings doesnt he lol
I'm also doing a bonnet latch conversion on my car so that you can pull the bonnet from inside the car simply because there is always a problem with these not working, the white plastic bit comes out the lock so when you put the key in it doesn't work, I have replaced my lock 3 times and it is really hard to get the bonnet open if the lock doesn't work Here is a youtube video on how to do it ruclips.net/video/9NwGBu4cICw/видео.html
Good video but the music throughout was awful 👍🏻
Why does your mate wear little girls trousers?
Social distancing? No ?
What with my housemate ?