DIY: Dodge 4.7L V8 Water Pump Replacement

Video tutorial on how to replace the water pump on a Dodge 4.7L V8, but it also does apply to other Chrysler models produced. Similar procedure can be used on the 1999 - 2009 Jeep Grand Cherokee, 2000 - 2011 Dodge Dakota, 2000 - 2009 Dodge Durango, 2002-2012 Dodge Ram 1500, 2006 - 2009 Jeep Commander, 2007 - 2009 Chrysler Aspen. This particular tutorial was done on a 2003 Dodge Dakota 4.7L V8 2wd.
Website: 4diyers.com
Facebook: / 4diyers
Google Plus: plus.google.co...
Twitter: / 4diyers
Instagram: / 4diyers
Tumblr: / 4diyers
Pintrest: / 4diyers
Tools/Supplies Needed:
-drain pan
-new coolant and distilled water
-socket set and ratchet
-vaseline
-torque wrench
-small adjustable wrench
-needle nose pliers
-wrenches
-hammer
-abrasive pad or emery paper
-clean rag
-new serpentine belt
-new mechanical fan clutch assembly
Procedure:
-first style by removing the washer fluid tank, disconnect the rubber hose and the two electrical connectors on the pump and level sensor
-the fluid will drain so have a drain pan handy or plug the pump
-now remove the two bolts on each side of the washer tank using a 10mm socket, 6" extension, and 3/8" drive ratchet
-remove hose by radiator cap for expansion tank
-remove two 10mm bolts on the top of the radiator which fasten it to the radiator support
-place a drain pan below the radiator and use a small adjustable wrench to loosen the drain plug
-the drain plug only rotates a quarter turn
-use needle nose pliers to pull out the drain plug
-use a larger adjustable wrench to loosen the clutch fan, leave the serpentine belt in place
-to remove the serpentine belt, use a 15mm wrench and rotate the bolt clockwise to relieve the tension
-place the drain pan under the water pump area
-check both the idler and tensioner pulleys to ensure they are in good working condition
-remove the idler pulley next to the water pump using a 15mm wrench
-use a 13mm to remove the water pump bolts
-when removing the water pump bolts, make note of all the locations as they are not the same
-sometimes the pump can be stuck in place, use the handle of a hammer to tap it free
-apply a small amount of vaseline to the new o-ring and push it into place
-use an abrasive pad or emery paper to clean the sealing surface, than wipe clean with a rag
-no need for silicone on the sealing surface
-when installing the new pump, tighten down evenly in a crisscross pattern
-to install a new mechanical clutch fan and remove the fan itself, use a 13mm to remove the bolts
-installation of all other parts in reverse of removal
-fill the system with coolant
-only use distilled water when mixing the coolant if need
-squeeze the lower rad hose to help push air from the system
-once filled, leave the radiator cap loose, start the vehicle and allow the engine to warm up
Torque Specifications:
Water pump - 43 ft. lbs.
Idler pulley - 40 ft. lbs.
Fan to mechanical clutch - 20 ft. lbs.
Symptoms of water pump failure:
-leaking gasket between the water pump housing and engine block
-worn seal around the shaft bearing which causes the coolant to leak out the bearing vent hole
-worn out bearing which would make a howling or grinding noise
-excessive "play" in the water pump shaft
Causes:
-regular usage which causes wear over time (routine maintenance)
-broken mechanical fan which causes the water pump shaft to be off balance
-worn mechanical clutch fan assembly which causes the water pump shaft to be off balance
-leaking water pump shaft seal which washes out the lubricant within the bearings
-worn/dried out gaskets/seals that cause a coolant leak
Thank you to all those who watch my videos and support my content. Don't forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!
© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.