2017-11-21, 08 02 20, Frigidaire Dishwasher, Self Diagnostic, Test Debug Cycle Mode, LFBD2409LF2B
HTML-код
- Опубликовано: 6 авг 2024
- 0:00 Oh, it's a latch thing.
0:05 But at least it start now. Before it wouldn't do anything at all.
0:20 The dishwasher door was hitting the cabinet wood on the left side, which was preventing the dishwasher from fully closing, so I scooted it back to the right a little bit.
0:25 If you push on it and press Start it will make a noise.
0:35 It just stops even if I was pushing the whole time.
0:40 It is a problem, but it's not the only problem.
0:45 Start process of getting dishwasher into diagnostic mode
0:50 Press High-Temp Wash & Start/Cancel simultaneously for a couple seconds
2:20 Fill Dispenser
2:35 That should last for 60 seconds
2:40 2nd test is fill until the float switch is activated and that runs for 27 seconds
3:10 That sound is maybe #2? Might be at step #3 already, which is WASH, the wash motor is activated. This test runs for 45 seconds.
4:10 Finished. Yup.
4:15 Small pause for 5 seconds.
4:20 We're at step #5 WASH HEAT, the wash motor and heater are activated. This test runs for 75 seconds.
5:00 This dishwasher is only 2 years old because bought in 2015.
5:50 Step #6 is similar to Step #5, so maybe hard to hear the change in the steps.
6:00 Step #6 is WASH/HEAT/DISPENSER, the wash motor heater element and dispenser vent are activated for 60 seconds.
6:25 Step #7 DRAIN, drain motor is activated to drain the water from the dishwasher
6:30 Sounds like it's draining now
6:40 This test runs for 90 seconds
7:20 Step #8 DRY, the heater element is activated. That will give another 90 seconds.
7:55 Sounds like it finished Step #7 DRAIN, so it's probably Step #8 DRY, heater element already.
9:05 Cycle #8 should be 90 seconds. DRY cycle, the heater element is activated.
9:25 Click. Sounds like it's finished.
Frigidaire Dishwasher Self Diagnostic Test Debug Cycle Mode LFBD2409LF2B Nikon S7000 ViewNx2
Frigidaire, Dishwasher, Self Diagnostic, Test, Debug, Cycle, Mode, LFBD2409LF2B, Nikon, S7000, ViewNx2, 2017-11-21, 2017Nov21, 2017 Nov 21, 2017Nov21st, Nikon S7000, Self-Diagnostic, Dishwasher Debug, Dishwasher Test, Dishwasher Repair, Repair, Dishwasher Self-Diagnostic, Test Mode, Debug Mode, Test Cycle, Debug Cycle,
Been trying to get mine to start for 2 days then I tried what is in the video press HI HEAT and START held it for a few seconds and wala it works fine now!!! Thanks!!!
Damn you are a lifesaver
Thank you for your video! I am renting apartment and I have this dishwasher and couldn’t understand why it not working. But now after I watch your video I realized I have to give it a push to start
I'm glad it helped.
Yep... 😁I felt like a dummy because I wasn’t pushing the door hard enough to start the wash. Thanks for the video 👍🏽👍🏽
To reset this model....unplug from source, wait 30 seconds, plug back in, lights will be flashing, hold start/cancel button down simultaneously with heat wash button. Hold until cycle commences.
Thanks!
I have same problem and going to try this, thanks
Did that now hi temp and heat dry light flash. Is this normal?
Corbo Yates
Did you ever find out what to do? Mine is flashing on start and I can’t get it to work I’ve cleaned out the drain all of it and nothing
@@corndoggbitch Did you ever figure out how to get yours back working? Mine has the same 2 lights but the reset didn't work for me.
Thank you it worked !!
thank you so much
Thank you!
Check the wires that plug into the door switch ,common problem they overheat and melt the connectors ,
I have the row of 4 lights flashing. It happens continually. Without unplugging the unit how do I reset the unit by pressing buttons?
Did you ever figure out the 4 light problem, I did reset it and do what's mentioned in the video, but they just come back. If you had any luck I'd much appreciate any ideas.
@@timjilman3295 One thing an electrician friend told me was that I might have reverse polarity in my plug. I did check it and sure enough, the black and white wires were reversed. We corrected that and found out from him that another major no-no was to have other plugs or lights on that same circuit. Sure enough, some rocket scientist had wired the dishwasher circuit sometime in the past and put it on a circuit with our bedroom plugs and lights. We are in the process of having that changed right now. If you have similar problems you might want to have them addressed. Also, if you ever replace the main board, don't throw away the old one, as the new one might do the same if you have similar problems as we do. I still have problems with trying to figure out what sequence resets the dishwasher.
Mine is still not working don’t know why
it doesnt work
I tried this and it didn't work. I have the same dishwasher it was hooked up and worked for 3 weeks then stopped working. Only lights show up tried resetting the breaker and what you did here still didn't work.... Idk what happened this dishwasher is garbage
Do you mean after pressing HiTemp & Start simultaneously for a long time, your dishwasher didn't enter into self-diagnostic/debug mode? It's difficult to see whether it does since the LEDs don't do anything. You have to kind of listen to whether you hear things going on that coincide with the expected debug mode time-frames. I thought I published those time-frames somewhere here, but maybe I published them somewhere else. Without those notes, I guess you could listen whether the sounds my dishwasher made in this video match the sounds you are hearing from your dishwasher. Let me know how that turns out or if you get new info.
Shanny Barfield you have to pushing it after you press start. And after a second it will lock and start working
damned dishwasher im pissed