***A NEW BUT OLDIE***1954 Chevy Bel-Air WITH A LS SWAP!! How did we do it?
HTML-код
- Опубликовано: 3 окт 2024
- This beauty has a LS swap, new wiring harness, new gas tank, new radiator, and much much more!! Come see how awesome this 69 year old runs like new!
I was born the same year love it
I'd like a driver like this
Nice ride
Thank you!
Your car is amazing considering it is 70 years old. Love it!
Hello, nice upgrade, what transmission crossmember did you use? Thank you
Waltonfab.com
Thank for watching!
@@gentrysgarage7956 Hello Sir, Good Afternoon. The Walton website sates there’s bolt in crossmember doesn’t fit for the L460E transmission? But I seen yours is a bolt in with an L460E, question is did you have to fabricate the mounts transmission? Thank you for your videos
I believe mine came with two different types of crossmembers, which are just a little flat bolt in pieces. One of them was a straight and the other one was offset to either of the front or rear, depending on which direction you put it in. The one I used is the straight one. If you do need to make one, they are pretty simple. The main part of the crossmember is the most important part.
Hey, did you have to relocate the hood latch when you moved the radiator forward ?
I didn’t relocate the hood latch, I just trimmed the hood
Hey, awesome work.
I had a question about the radiator and the fan set up did you go with. And did you move it forward for clearance..?
Thank you.
I went with a radiator from wizard cooling, and I had to move it forward, build a bracket and trim the inside of the hood
Very nice
I need help
Did you have to cut the tunnel or firewall
Which headers did you use
Thanks
I had to cut this supports that stick forward off the firewall, but not the firewall and did not have to cut the tunnel. The headers are just cheap stainless steel. LS swap headers off of Amazon. They are the ones with the van clamps, and the extensions for the O2 sensor.
Thanks
I am gonna start my ls swap soon, can you provide info on trans crossmember
Waltonfab.com
Todd Walton
(603) 347-5693
Kingston, NH
Thanks for the help
Pete
You’re welcome! Thanks for watching and sharing!
I doing the exact same build right now. I have some questions on the radiator. What hoses did you use?
Did you have to cut your hood support?
Is your intake 4 inch? I don't have much room so im hoping the intake i ordered fits.
I did have to cut the hood, don’t remember what hoses and I believe a 4” intake
@@gentrysgarage7956 OK, thanks.
Thanks for watching and sharing
Which radiator did you go with?
It’s a radiator from Wizard cooling but I did have to notch and move the radiator. I also trimmed the hood.
😎👍
What type/make shifter is that?
It’s a Lokar floor mount
Did you use stock exhaust manifolds
No, just some cheap Amazon LS swap headers
What did u use for your motor mounts? Thanks in advance
The engine side is just ls swap aluminum mounts
The car side is from
Waltonfab.com
Todd Walton
(603) 347-5693
Kingston, NH
54sRule!
What drive shaft are you using?
I had one made at a local driveshaft shop here in town
What kit did you use for cold air intake piping.
Airaid u-build it master kit. Thanks for watching
@@gentrysgarage7956 cool. Thank you
How much fab work was needed to ls swap it
Thanks for watching! It wasn’t a lot of fab work. Some bracing on the fire wall had to be removed, radiator moved, motor mount and transmission cross member kit.
Do you have part numbers for the kits?
I’ll see if I can find them for you
Waltonfab.com
Todd Walton
(603) 347-5693
Kingston, NH
@@gentrysgarage7956 thank you!
Any idea on how it will be on my 53 road master with a straight 8
I don’t know. Thanks for watching!
What Ls engine was used, what vehicle was the engine harvest from? Thanks
5.3 out of a 2005 Tahoe, Thanks for watching
@@gentrysgarage7956thanks. I was looking at putting an LS in my 54 New Yorker
@@myfaaammilly1607 this car runs very well!
what trans crossmember is that
The transmission is a built 4l60 and the crossmember is from Walton fab
Waltonfab.com
Todd Walton
(603) 347-5693
Kingston, NH
So beautiful, except th colour…
We love the color! Thanks for watching
How much to do it to my car
How much do it to my car?
I just want to know what trans crossmember you are using radiator i am doing a 54 wagon at the moment and I already bagged it all around also
Waltonfab.com
Todd Walton
603-347-5693
The radiator is from wizard cooling
That sounds awesome! Thanks for watching!