@BoosterUM they're either a troll or a bot, either way ignore them. If they're for sure a bot (identical posts in every comment thread) report it as spam.
that should have been part of the video. given how easily lpl found the right set on each pin, I'm inclined to believe that raking still has a reasonably good chance of working. though it should take several times longer than with all standard pins.
@@Ass_of_AmalekWell, keep in mind he also knows this lock really well. If the only thing they replaced were the pins, he could probably rake it a lot easier than someone less familiar could. Like how replacing just the cushions on your couch won't have much effect on your ability to navigate the living room.
Anyone watching this video is probably capable of re-pinning the lock with whatever pins seem best. How is the quality of the lock otherwise? Can it be made good?
LPL had more problems getting the assembly screw out than picking the lock. A miracle just happened, LPL actually praised ML, if only slightly. The world is officially coming to an end.
The expression you are looking for is "damned with faint praise". Someone a bit earlier said Masterlock is going "back to the drawing board" on this - naah. Masterlock have their products and they are making a very nice -product- profit, thank you. Why spend money on R&D? Don't be silly.
“For that, I do commend Master Lock.” In other news, Demon News reports that the weather in Hades is below freezing and the whole place has frozen over.
It couldn't be raked (or at least didn't appear to be from this video) and LPL said it was an improvement. That is one of the best reviews of a masterlock I've seen on this channel.
@@weswheel4834 IIRC he said he prepares in advance, to make the videos shorter, so unless he says so, I assume he has already picked the lock before (and it is easier the second time). There are a few videos where he opens the package on camera, he is still really fast when going blind, but maybe not as perfect as this.
@@gubx42 Yeah, I wasn't criticising him. But obviously if he's just picked it off-camera then it isn't really fair to compare his time (as I did) to the time that someone may take to pick it in the wild :)
LPL: "Don't expect this to last more than 30 seconds or maybe a minute when being picked." LPLs actual pick time was 11seconds, but I guess getting the tools out and into position, and explaining it while filming took 38 seconds total. So he was correct: 30 seconds to a minute. Someone could make a video of picking your lock, taking your valuables, and disappearing all in under a minute.
Master lock makes their units more difficult to dissemble instead of increasing the difficulty of its pick resistance. Put the core on the inside of the shackle and the hex screw in the key hole. Perps would at least be confused at first. And then have to go into their tool box for an L key. Increasing the time significantly
I have actually seen someone use structural screws to seal a door shut. Sure, the key is technically common but it's going to be really loud to open or extremely time consuming if they want to unscrew it by hand.
@@Yukimaru0 could also just bring out the welder and just weld it shut, that way nothing less than an angle grinder will allow people to go through, sure to be woken up at night
Nice to see a pick and gut video again. Used to love watching those back in the day. That sound of the pins sliding when the core was being pulled was always something I looked forward to.
Yesterday someone had trouble with a Master lock combination lock where I was. Even with the correct combination it wasn't opening. I tried myself but couldn't get it, then I remembered your videos where locks had been struck with a mallet and opened that way and asked if there was something solid we could use. A person had a Swiss Army tool and managed to use it to pry the lock open, not quite the same result but none the less a problem avoided thanks to your teachings LPL.
it'd actually be a little more difficult if it had 3 or 4 spools, because you have to be careful when pulling the spools out of a false set to not drop pins that are fully set. Still a nice improvement from masterlock though, and likely wouldn't be able to be raked open with most bittings, which is likely all this needs to protect against in reality.
So instead of making it meaningfully harder to pick, they just made it slightly harder to take apart to show why it's so easy to pick. Bravo, Masterlock.
Seeing the speed he pick and disassemble a lock, I think LPL would be the style of thief that leaves a key impression of the key and a note on why the lock wasn't secure after a break-in just to taunt even more the victim.
I'd love to explore how you choose which tools from your kit to use. As an very amateur hobbyist, choosing the tools and using the tools are the two variables I need to work on. Thanks : }
I find it so interesting how easy a master picker can open what should be a strong average lock. It must be sad and boring for LPL to not have a serious challenge to go through from time to time. Thank you for sharing the video that you create.
At least it actually required single pin picking and not the good ole wave rake! I'm still a bit surprised the spools didn't slow him down a tiny bit more.
So a terrible lock is a little less terrible now…got it! The fact that it took more time for LPL to OCD the pin orientation on the plate than it took him to pick the lock says it all.
I just bought this the other day and had a lot of trouble picking it (I'm a bit of a noob) I watched a few videos of the older revision and it looked so much easier, and they didn't have spools! I thought I was really bad if I had trouble getting standard pins open. Glad to know it was spools! I've picked it once but this will be a good lock to improve my skills
Chopsticks are ez to use for someone with good dexterity with their hands such as a puzzle enthusiast or a competitive or professional lockpicker I wouldn't doubt it.
Funny part for me, at about the start of the picking, I was picking an Abus 80TI/50 and got though it at almost the same time. My end is definitely just familiarity though, I know I'm not that good. I just found it to be a funny coincidence
Master Lock made a lock with all security pins, and LPL blazed through it in one pass faster than other Master locks he basically just shakes his head in disappointment at to open.
When I first saw that this was a 4 minute and 40 second video about a Master Lock, I got a little excited. Turns out that 3 mins and 20 secs out of the 4 mins and 40 seconds are just him tearing the lock down. Oh well, I should've known 🤣.
Dang man you took it completely apart faster than most people could pick it. Not to mention you picked it faster than I could have raked it with all standard pins lol
At first I thought the video was 23 mins long and thought "Wow, finally a good lock". Then I realized I read it wrong that the video was only 4 mins long and was POSTED 23 mins ago.
![[1550] Better Than Expected: Toledo 40mm Alum. Padlock](http://i.ytimg.com/vi/2GJpGl4CsAI/mqdefault.jpg)
![[1550] Better Than Expected: Toledo 40mm Alum. Padlock](/img/tr.png)
![[1181] A TRAP For Pickers! The Clever Hines Key System Picked](http://i.ytimg.com/vi/3g0-pxXD794/mqdefault.jpg)
About 2 seconds per pin. That’s remarkable for a Master Lock.
I told my infant to blink if they’re trans. They blinked. My infant came out as trans.
@@TransKidsMafia Sounds like they’re more secure than a Master Lock.
I wanted to see him try to rake it anyways
@dli7423 tf are you talking about. Is bait the only thing that gets you off?
@BoosterUM they're either a troll or a bot, either way ignore them. If they're for sure a bot (identical posts in every comment thread) report it as spam.
Well as long as it cannot be easily raked, its a huge improvement.
that should have been part of the video. given how easily lpl found the right set on each pin, I'm inclined to believe that raking still has a reasonably good chance of working. though it should take several times longer than with all standard pins.
@@Ass_of_AmalekWell, keep in mind he also knows this lock really well. If the only thing they replaced were the pins, he could probably rake it a lot easier than someone less familiar could. Like how replacing just the cushions on your couch won't have much effect on your ability to navigate the living room.
I'm sure McNally will find a way to open it with his signature ramming method
@@DeathsWeepingAngel methode anlauf statt gleitgel, as we say in germany
Anyone watching this video is probably capable of re-pinning the lock with whatever pins seem best. How is the quality of the lock otherwise? Can it be made good?
LPL had more problems getting the assembly screw out than picking the lock. A miracle just happened, LPL actually praised ML, if only slightly. The world is officially coming to an end.
The expression you are looking for is "damned with faint praise".
Someone a bit earlier said Masterlock is going "back to the drawing board" on this - naah. Masterlock have their products and they are making a very nice -product- profit, thank you. Why spend money on R&D? Don't be silly.
Ya I think that's an end times proficiency
peace in Israel and the lock picking lawyer makeing peace with Master lock.
His words where faint praise but his skills were still scoffing ML
He had more trouble putting the pins on the tray. 😂
If "congratulations for doing the bare minimum" was a compliment 🤣
Oh boy! A Master Lock video? And its longer than 3 minutes? Its a miracle!
my toddler came out as trans. They’re living their truth
No miracle - it took much, much longer to disassemble the lock than to pick it …
Only because LPL takes apart the lock.
Twenty seconds to pick, the rest is additional material.
Get jebaited 😅🤣
“For that, I do commend Master Lock.” In other news, Demon News reports that the weather in Hades is below freezing and the whole place has frozen over.
In the spirit of The Tim Traveller: In Dante's _Inferno_ one of the circles in fact _has_ frozen over.
Is that part of Donut News Network?
And their ceo just committed friendly Gand rape of his engineers…
Plus, pigs were flying all over the place.
@@williamromine5715I've seen it on a Pink Floyd album.
See's it's a 5 minute video featuring a Masterlock: Ooooh...oh wait he's just taking it apart
It couldn't be raked (or at least didn't appear to be from this video) and LPL said it was an improvement. That is one of the best reviews of a masterlock I've seen on this channel.
From touching the first pin with your pick, that took you about 10 seconds, with spool pins. You truly are a master of your craft.
I liked where he converted that time to a time for someone who "knows what they're doing" (30 seconds to a minute).
He only needed one pass thru the pins as well, so little lucky?
@@ArmadilloGodzilla I wonder if it was because he’d picked it prior to the recording, and knew that they were spools.
@@weswheel4834 IIRC he said he prepares in advance, to make the videos shorter, so unless he says so, I assume he has already picked the lock before (and it is easier the second time). There are a few videos where he opens the package on camera, he is still really fast when going blind, but maybe not as perfect as this.
@@gubx42 Yeah, I wasn't criticising him. But obviously if he's just picked it off-camera then it isn't really fair to compare his time (as I did) to the time that someone may take to pick it in the wild :)
LPL: "Don't expect this to last more than 30 seconds or maybe a minute when being picked."
LPLs actual pick time was 11seconds, but I guess getting the tools out and into position, and explaining it while filming took 38 seconds total.
So he was correct: 30 seconds to a minute.
Someone could make a video of picking your lock, taking your valuables, and disappearing all in under a minute.
Master lock makes their units more difficult to dissemble instead of increasing the difficulty of its pick resistance. Put the core on the inside of the shackle and the hex screw in the key hole. Perps would at least be confused at first. And then have to go into their tool box for an L key. Increasing the time significantly
Which makes sense, if you are trying to quietly get a lock open it makes sense to just take it apart if the low skill attacks dont work
I have actually seen someone use structural screws to seal a door shut. Sure, the key is technically common but it's going to be really loud to open or extremely time consuming if they want to unscrew it by hand.
@@Yukimaru0 could also just bring out the welder and just weld it shut, that way nothing less than an angle grinder will allow people to go through, sure to be woken up at night
@@celivalg Why stop there? Encase the whole thing in concrete after you weld it. A jackhammer is gonna be even louder than an angle grinder.
@@Just_A_Dudewhy stop there? Send the whole thing into space. That way if it gets broken into, you know you can just blame Elon Musk
A Master Lock Video, this will be quick
@@TransKidsMafiathen you have failed them. Weirdo!
Ho ho.
Yes mrs LPL 's beaver needs raking out of some dust with the big 8 inch rake pick. 😎🤣😜 So a quik and easy master junk video and back to the beaver...
Nice to see a pick and gut video again. Used to love watching those back in the day. That sound of the pins sliding when the core was being pulled was always something I looked forward to.
It took longer to unscrew the hex screw than it took to pick the lock!
The pin at 3:49 put up more of a struggle in the tray then it ever did in the lock.
*than
MasterLock: You don't seem him slipping a shim into the shackle, do you? These are new and improved!
masterlock: We finally got him!
LockPickingLawyer: picks it almost as fast as using a key.
masterlock: ...back to the drawing board, boys!
more like
"technically, we did try. good enough, I say!"
LPL: I do commend MasterLock
MasterLock: we are now recommended by LPL!
new achievement: no wave rake by LPL
Master lock is security by obscurity... ( sorry lpl i stole that one from you )
Lol master lock just wants $ everything else is a lie.
The new pin tray looks great! I can't wait to see McNally use it as a throwing blade to explode a Dr. Pepper or something.
No, it'll be thrown into the void when he opens a lock and sees the disappointment
Nah he will gently tap the lock with it to open it then launch it through a watermellon
The sound of the tweezers scraping was like nails on a chalkboard to me unfortunately.
I was actually picking a 930 at work the other day and was surprised when I felt a spool. I had to double check that it WAS a Master lock lol.
I'm a simple man. I see a teardown of a lock, and I hit that like button.
What's even more amazing is LPL puts them back together in working order.
I mean with the Master Locks, he might as well just huck em in the bin 😅.
"I do commend Master Lock" Truly a sign of the apocalypse.
Finally a video featuring picking and gutting. I missed these. That's the single reason why I sub this channel. Keep it up.
Very nice demonstration.
Took him longer to get the pick and turner out of the covert companion
Oooo, I think, a 4:40 LPL video, maybe Masterlock has raised its game. Then, ten seconds later, "we got this open"!
I see a video over 2 minutes, i am astounded by the lock and instantly intrigued.
I love spool pins. They tell you exactly what they are, and exactly what's going on with them.
Old school lock pick and gut! Miss seeing these.
Permanently closed- that means master lock is more afraid of you opening the cylinder than the lock
Then why didn't they wrap it in duck tape? (-:
Master Lock should know by now that nothing is closed to LPL! 😂🤪
You know, Masterlock executives only heard LPL say "I do commend Masterlock".
The fact it took you three times as long to get the hex screw out compared to picking it is hilarious
LPL: "Definitely an improvement ..."
Masterlock: "Mass produce them! NOW!"
Good joke, but Master Lock doesn’t make anything not mass produced. Maybe double the production rate instead?
Awesome to see another disassembly!
Well, at least it took more than a gentle raking, I suppose
A Master Lock that doesn't just melt in his presence is a big improvement !
I especially enjoy the videos in which he takes the lock apart and shows us what's inside.
I don't think I've seen a gutting video since Bosnian Bill was active, much appreciated!
Lock Noob does a ton of them still
I love how concise your videos are. Thanks.
Yesterday someone had trouble with a Master lock combination lock where I was. Even with the correct combination it wasn't opening. I tried myself but couldn't get it, then I remembered your videos where locks had been struck with a mallet and opened that way and asked if there was something solid we could use. A person had a Swiss Army tool and managed to use it to pry the lock open, not quite the same result but none the less a problem avoided thanks to your teachings LPL.
What a boss. Setting 5 spools like it's nothing. The pro series is just like this but 6 pin (if the locksmith puts in all 6)
it'd actually be a little more difficult if it had 3 or 4 spools, because you have to be careful when pulling the spools out of a false set to not drop pins that are fully set.
Still a nice improvement from masterlock though, and likely wouldn't be able to be raked open with most bittings, which is likely all this needs to protect against in reality.
Nice lock, great picking and tools, but then it's you !!!!!
have a great day
I am amazed after all the years of lock makers making locks you can still pick locks this easily. Especially from master lock.
Good job Master lock for adding security pins that will at least make simple picking techniques like raking more challenging.
Damn! You can't trust your dirty secrets to any lock if this guy is around
Love seeing a tear down!
So instead of making it meaningfully harder to pick, they just made it slightly harder to take apart to show why it's so easy to pick. Bravo, Masterlock.
Amazing! I don't think I've ever heard charitable words for Master on this channel.
Would love to see a full size Pinning Tray, similar to the ones you've used on the Covert Instruments store!
Thank you, I always learn something from your videos.
"If someone knows what theyre doing, dont expect this to last more than 30 seconds or a minute." He said, after picking it in like 10 seconds.
On the next MasterLock commercial and all over every website they own:
"I do commend MasterLock" - LockPickingLawyer, October 2023
Seeing the speed he pick and disassemble a lock, I think LPL would be the style of thief that leaves a key impression of the key and a note on why the lock wasn't secure after a break-in just to taunt even more the victim.
22 seconds from beginning to end, a remarkable improvement for Masterlock. Thank you to all the people who emailed him about this lock. 😅
An effort by ML. Outstanding. Now let’s see them populate the sixth pin location.
Good old Master Lock! Rave reviews from LPL!
"Hex screw down the shackle hole" now lives rent-free in my head.
You have some good damn tools and you plug them just as good
It took longer to get ready to pick than the actual picking itself. Way to go, Masterlock.
"down the shackle hole" sounds like a LPL movie title
I'd love to explore how you choose which tools from your kit to use. As an very amateur hobbyist, choosing the tools and using the tools are the two variables I need to work on. Thanks : }
You upload so regularly. Thank yoiu.
I find it so interesting how easy a master picker can open what should be a strong average lock. It must be sad and boring for LPL to not have a serious challenge to go through from time to time. Thank you for sharing the video that you create.
All spools. Ahhhh master. Never stop being you. 😘
Master lock... We came out with a new design, its un pickable!!
LPL... Hold my wiskey and watch this!!
At least it actually required single pin picking and not the good ole wave rake! I'm still a bit surprised the spools didn't slow him down a tiny bit more.
"Obviously an improvement." Champagne corks popping over at master lock.
Without watching the video, my first thought was: "Oh, it cannot be opened with just anything now? I'm officially intrigued!"
This would be the closest to a “Master Lock sponsored” video by LPL I can think of.
Wow over 4 minutes. Masterlock must had really improved their pins. Oh nvm....he just spends 2 1/2 minutes taking the lock apart to prove his point
Masterlock: New and improved!
LPL: That's cute
Nice to see a disassemble again. I've missed those.
Monumental occasion, masterlock improved something
Master lock decides to improve their lock, does the bare minimum. One small step for master lock. That’s it, that’s all I got. One small step.
So a terrible lock is a little less terrible now…got it! The fact that it took more time for LPL to OCD the pin orientation on the plate than it took him to pick the lock says it all.
I just bought this the other day and had a lot of trouble picking it (I'm a bit of a noob)
I watched a few videos of the older revision and it looked so much easier, and they didn't have spools! I thought I was really bad if I had trouble getting standard pins open.
Glad to know it was spools! I've picked it once but this will be a good lock to improve my skills
Random thought here:
Lockpicking Lawyer is probably REALLY good with chopsticks.
Just saying 😂
Great Video btw!
😂
Chopsticks are ez to use for someone with good dexterity with their hands such as a puzzle enthusiast or a competitive or professional lockpicker I wouldn't doubt it.
I just bought one of these on 1/4/23. Picked it blind in one attempt, about 8 seconds. Gutted and found 5 standard pins.
Interesting to see what you are talking about when you say a spool pin. I enjoy your work and seeing the details helps.
MasterLock: "We need security pins in our locks!!!" - "just lets make 'em all spools! Those are tricky!!" - "great Idea! And we can mass produce 'em"
Thanks LPL
* grabs chest *
A praise for Master lock?!
Not used to that
Perhaps there is hope.
WOW, It took you longer to get the hex head screw out than it did for you to pick the lock. Well done!
Master Lock actually made a lock that lasted longer than a split second before it was picked! This one takes 5 to open! Impressive!
Funny part for me, at about the start of the picking, I was picking an Abus 80TI/50 and got though it at almost the same time. My end is definitely just familiarity though, I know I'm not that good. I just found it to be a funny coincidence
Master Lock made a lock with all security pins, and LPL blazed through it in one pass faster than other Master locks he basically just shakes his head in disappointment at to open.
I'm going to have to use the phrase "right down the shackle hole" in a conversation.😂
“Clearly 5 spools…” after picking it in like 9sec. 😂😂 wth man! 😅 1:20
oh good, master bought some spool pins. anyways...
When I first saw that this was a 4 minute and 40 second video about a Master Lock, I got a little excited. Turns out that 3 mins and 20 secs out of the 4 mins and 40 seconds are just him tearing the lock down. Oh well, I should've known 🤣.
Congrats on your weight loss, hope you're doing well.
Dang man you took it completely apart faster than most people could pick it. Not to mention you picked it faster than I could have raked it with all standard pins lol
I liked seeing the disassembly of the lock
I've said this before, but I genuinely think spool pins are actually easier to pick. There is no doubt about when you set a spool pin.
LPL- looks at the lock sternly. Lock in a sorrowful tone, "Fine." Lock opens up.
"I do commend MasterLock." -LPL
🍾
New product suggestion: a notched follower that will work on cylinders like that.
Missing episode numbers?
The previous episode, from a few days earlier, was [1567] yet this jumped to [1578] - why where 10 skipped?
I saw that it was an almost 5 minute video and thought holy crap did master lock upgrade their lock? Nope! It’s just him disassembling it.
At first I thought the video was 23 mins long and thought "Wow, finally a good lock". Then I realized I read it wrong that the video was only 4 mins long and was POSTED 23 mins ago.
Any lock keeps an honest man honest, thieves will defeat locks quickly.