@@EmtremeNips153 yes the ebay seller sent me a new one but I'm still having trouble accessing all the options like clocks etc. But I can now fully access the engines ECU
Same issue here. I had a working one, it stopped working, now all I get is the communication error, not powered from car message. Bought a new one, same issue
@@subsalza Win Xp. 1)First start program ( Run as Admin) the clone needs hacked FTDI drivers to work and this is the only way to run the hacked drivers also untick prevent from using un certified drivers... 2) Without conectict to car conect USB and Opcom clone.. Settings... Test interface... Click OK... Then click save settings.. 3)Don't conect it to car untill after you press (diagnose the part you want to diagnose) example after engine.... That works for mine... 1.99
Creo que pone que compro una nueva, yo tengo el mismo problema con dos diferentes, vamos a comprar una nueva, si as logrado solucionarlo tu dime como y si logro yo solucionarlo te digo. Gracias.
I found leaving op-com unplugged, get same error of not being powered or connected, go back and retry with op-com still disconnected and most will then skip through to initializing ECU and at that point plug in to OBD2 port... if you're lucky it will negotiate a connection and then that particular control module should be readable and programmable.
@@bezaleeluk3696 I could only get the 2010 software to work in my car. 2012 and 2014 will not work. But I managed to program a key with 2010. And clear codes. Even though my car is 2011!
Error while creating license dat??? The list of supported ecus cannot be loaded ??? Interface communication error or interface not powered from car.. what should I do ???
@@scott2735 cool thanks Scott it's just I get .. vaux then this 120309a+131223dgb then China clone .. (3 programs) .. would I need the car running I'm guessing you don't
It turned out the tool was at fault
scott alexander did you get it fixed ??
@@EmtremeNips153 yes the ebay seller sent me a new one but I'm still having trouble accessing all the options like clocks etc. But I can now fully access the engines ECU
Same issue here. I had a working one, it stopped working, now all I get is the communication error, not powered from car message. Bought a new one, same issue
Hola que hicistes al final con la interface, yo también tengo mismo problema
There’s a trick to get it to connect, u don’t have it plugged in untill u hear the click.
At 2:00 u mentioned a click, that’s when u plug it in.
I know video is old and probably you forgot about it but today I make mine working perfect on win7 and win10. I had exactly the same issues like you.
How ?
Hi, I am struggling with the same error . V1.99 and windows 10. How did you solve the issue?
So it's not just me having this problem
I can't seem to work this out
Can you please tell us how to fix it?
@@subsalza Win Xp.
1)First start program ( Run as Admin) the clone needs hacked FTDI drivers to work and this is the only way to run the hacked drivers also untick prevent from using un certified drivers...
2) Without conectict to car conect USB and Opcom clone..
Settings... Test interface... Click OK... Then click save settings..
3)Don't conect it to car untill after you press (diagnose the part you want to diagnose) example after engine.... That works for mine... 1.99
Hello Scoot.First you have to install the latest driver from the disc. After that test the interfaceAfter that diagnostic.Good luck.
I just got mine it's doing exactly whats ur doing
Hello have firmware 1.99 for download ?
Ive got same issue any idea how to get ut right
Put the China clone soft in the desk
„Timeout occured” how to solve this one?
Someone said use 2008 / 2010 software not this latest software
I've found 1.99 to be hit and miss... I use 1.95, no problems whatsoever
Is that the genuine one from opcom
Hi mine I can’t find usb. I don’t now why
Hola amigo que hicistes al final con la interface, la cambiastes? O la hicistes funcionar, gracias
INSTALAR LOS DRIVERS CORECTAMENTE
Ich habe gleiches Problem. Don't work!!
Tengo el mismo problema no hay manera de conectar si algún sabe la solución en Español
Creo que pone que compro una nueva, yo tengo el mismo problema con dos diferentes, vamos a comprar una nueva, si as logrado solucionarlo tu dime como y si logro yo solucionarlo te digo.
Gracias.
chicos, habeis conseguido que os funcione en el w10?
I can't see how the unit can be faulty when it passes the interface test. Others have said leave the car unplugged. Not tried this yet though.
I found leaving op-com unplugged, get same error of not being powered or connected, go back and retry with op-com still disconnected and most will then skip through to initializing ECU and at that point plug in to OBD2 port... if you're lucky it will negotiate a connection and then that particular control module should be readable and programmable.
@@bezaleeluk3696 I could only get the 2010 software to work in my car. 2012 and 2014 will not work. But I managed to program a key with 2010. And clear codes. Even though my car is 2011!
WHATS THIS THE PROBLEM ?
Hello Scott , i have exactly same problem. Have you solve it ? could you reply please?
It's the tool that's at fault send it back and get a new one
Error while creating license dat??? The list of supported ecus cannot be loaded ??? Interface communication error or interface not powered from car.. what should I do ???
Contact the seller, explain the situation and send it back as its probably faulty like mine was.
@@scott2735 cool thanks Scott it's just I get .. vaux then this 120309a+131223dgb then China clone .. (3 programs) .. would I need the car running I'm guessing you don't
@@shivt91 you need the ignition on
@@scott2735 actually running 3rd position?? (Engine running) thanks
@@shivt91 no just second position on the key you dont need the engine running you just need power to the ECU