thank you very much there for the good tip i was getting aggravated because it wouldnt dump that good and i was spilling my dirt out thanks again very much helpful................got a question is there anyway to make the loader arms raise any higher
Hey Juice man v were, did ubuy ur excavator, an bulldozer? 1 more thing: is, the full metal dump truck way better then the plastic, and alloy material?
Neat video, thank you. And a very nice mod, well thought out. Have you had any other problems with the machine? Do you use a dump truck of any kind, if so which one? I'm keen on a Huina 580 excav. but I'm struggling to find the same scale in Volvo 6WD tipper. Again a great video with a nifty resolution to a design fault. Thankyou
Thanks and the only other problem is that my rear axle motor burned out but after that no more problems and I have the huina tipper it’s ok for paved surfaces but not that good in the dirt
I am still waiting the loading video There is a mistake on there design the at the bigining of the arm hing it is the same axis with bucket actuater axis
MrBlackbirdrider honestly I tried to replace the motor but is just burned my controller board even with the same voltage motor like off of a MINI-Z racer
@@datssan and i just meant like a 1mm bit, just to get rid of the "clang" sound when the bucket falls back, dont think that could harm anything, there will still be plenty of room behind the bucket
MrKeys57 the thing is that there is a limiting switch the the ram has to touch so it stops if the switch doesn’t get pressed by the servo the mother board will keep sending power and they will both burn out
This will be my first upgrade thanks for the video
no problem thanks for watching
Same didn't even know thanks
GOOD JOB!
Good shit man.. now I Kno wat to do wen I get mines.. 👍
MR.Sinister 1 thanks
beautiful video what size was thankful mm
Good video 👍 my friend 🤗
thank you very much there for the good tip i was getting aggravated because it wouldnt dump that good and i was spilling my dirt out thanks again very much helpful................got a question is there anyway to make the loader arms raise any higher
Yes you will need arm extensions I 3D printed some I’ll see if a can make a vid
How long was the new bar???
About 3/8” longer
Hey Juice man v were, did ubuy ur excavator, an bulldozer? 1 more thing: is, the full metal dump truck way better then the plastic, and alloy material?
Thanks for video could u tell me what size the arm is u put in there
It was about 3/8” of and inch longer
Great video, well explained, thanks
thanks
Were, did you get that metal rod an how, log does it need to be?
Neat video, thank you. And a very nice mod, well thought out. Have you had any other problems with the machine?
Do you use a dump truck of any kind, if so which one? I'm keen on a Huina 580 excav. but I'm struggling to find the same scale in Volvo 6WD tipper.
Again a great video with a nifty resolution to a design fault. Thankyou
Thanks and the only other problem is that my rear axle motor burned out but after that no more problems and I have the huina tipper it’s ok for paved surfaces but not that good in the dirt
@@datssan thanks brother, very helpful. Best wishes.
How long did you make the new dogbone? I just got a new 583 and that’s a mod I’d like to do along with fixing the free play in the bucket.
it would help if would if you would provide the measurements of the new dog bone thanks
wilson bonilla it’s about 3/8” longer
I am still waiting the loading video
There is a mistake on there design the at the bigining of the arm hing it is the same axis with bucket actuater axis
ruclips.net/video/6ydFxFoJUHo/видео.html
Is there any mods for speeding up the turning of the loader?
MrBlackbirdrider honestly I tried to replace the motor but is just burned my controller board even with the same voltage motor like off of a MINI-Z racer
w@@datssan
What is the measurement between the holes (centre of holes) on the new dogbone?
Goolge Hatter it’s a half inch longer then the original one
Thank you@@datssan
👏👏
i think i will just put a bit of foam behind the bucket... :D
MrKeys57 you can burn the motherboard and the servo like that
@@datssan oh! sounds serious! i will get mine later this week, just ordered it, greets, Levi
@@datssan and i just meant like a 1mm bit, just to get rid of the "clang" sound when the bucket falls back, dont think that could harm anything, there will still be plenty of room behind the bucket
MrKeys57 the thing is that there is a limiting switch the the ram has to touch so it stops if the switch doesn’t get pressed by the servo the mother board will keep sending power and they will both burn out
@@datssan ok, i really dont understand, but i dont want to destroy my loader, will put nothing ;)
How much price
Around 250 USD
@@datssan that product prices
How much is it?
RC-Cambodia about 250ish
Juice man uneed a link for this video,.)
Cuanto cuesta el cargador frontal
Check out my custom upgraded 583!!
ruclips.net/video/cELq7CN-pUs/видео.html
Русские здесь есть?🙄🙄🙄
No