Interesting video,makes you appreciate the skill of the designer to craft all these intricate parts to make this pistol all those years ago,thanks for the video..
Колодка и детали УСМ сделаны методом литья, до сих пор встречал только фрезерованные варианты. Детали настолько идеально сделаны, что это напоминает современную копию.
It would be beneficial if the warning below was added to the video. The coupling that holds the spring in can be inserted upside down, and the lock assembly and the gun fully assembled. BUT THE FIRST TIME THE SLIDE IS RACKED, THE GUN WILL JAM AND CANNOT BE UNJAMMED NOR DISASSEMBLED. Only an expert gunsmith very familiar with Broomhandles can drill a hole through the frame, use a special pick to lift the upside down coupling enough to allow disassembley, and braze the hole closed afterwards.
A few years ago there was a video about a special pick being sold which allowed reaching and moving that part without drilling the hole. I don't remember who was making them, and haven't even seen the video iteself in years, but the pick does exist.
Ахуеть ? На заре двадцатого века , когда люди жили при свечах , керосиновая лампа считалась роскошью , лошадь была основным средством передвижения , а тут целая куча точных , фрезерованных деталей , собранных в единый , безотказный механизм ! Умели же люди , делать ВЕЩИ !!!
thanks for this video. i got my c96 yesterday and while field stripping the disconector fell of but when i put it back on i had trouble with hammer not staying cocked and trigger not working. then from this video i figured out the hammer spring and disconector were in wrong spot then i got it working. i will try to fully dissasemble and reassemble lock frame later
my pistol is M712 mauser germen that ha charger and there is diffrence between M712 locking frame and c96 i want M712 locking frame assembly and disambly
This video was invaluable as I replaced the main spring and needed to reassemble the works. Yours is the only video I could find to not mess up. Most just said don’t disassemble any further...Well, I wanted to replace the spring so I needed your video. THANK YOU much!
Interesting video,makes you appreciate the skill of the designer to craft all these intricate parts to make this pistol all those years ago,thanks for the video..
Колодка и детали УСМ сделаны методом литья, до сих пор встречал только фрезерованные варианты.
Детали настолько идеально сделаны, что это напоминает современную копию.
Nice, keep the good work. I learn a lot about disassembling and reassembling this gun.
It would be beneficial if the warning below was added to the video.
The coupling that holds the spring in can be inserted upside down, and the lock assembly and the gun fully assembled. BUT THE FIRST TIME THE SLIDE IS RACKED, THE GUN WILL JAM AND CANNOT BE UNJAMMED NOR DISASSEMBLED. Only an expert gunsmith very familiar with Broomhandles can drill a hole through the frame, use a special pick to lift the upside down coupling enough to allow disassembley, and braze the hole closed afterwards.
A few years ago there was a video about a special pick being sold which allowed reaching and moving that part without drilling the hole. I don't remember who was making them, and haven't even seen the video iteself in years, but the pick does exist.
Ахуеть ? На заре двадцатого века , когда люди жили при свечах , керосиновая лампа считалась роскошью , лошадь была основным средством передвижения , а тут целая куча точных , фрезерованных деталей , собранных в единый , безотказный механизм ! Умели же люди , делать ВЕЩИ !!!
thanks for this video. i got my c96 yesterday and while field stripping the disconector fell of but when i put it back on i had trouble with hammer not staying cocked and trigger not working. then from this video i figured out the hammer spring and disconector were in wrong spot then i got it working. i will try to fully dissasemble and reassemble lock frame later
Thanks for posting. Video is good tutorial, very clear and concise.
Good job and thank you 🙏
M712 mauser loking frame assembly?this is c96 locking frame assembly
i want m712 locking frame assembly and disimbly
this is c96 assembly and disambly
there is diffrence between c96 and M712 locking frame
my pistol is M712 mauser germen that ha charger and there is diffrence between M712 locking frame and c96 i want M712 locking frame assembly and disambly
И не такой уж он и сложный в разборке сборке ..классный пистолет 👍
M712 mauser germen loking frame assembly and dessembly i want
This is c96 and i have M712 pistol plz upload M712
Hallo
nice video for explain the C96.
Which part is the contact breaker ?
THX for the information
This video was invaluable as I replaced the main spring and needed to reassemble the works. Yours is the only video I could find to not mess up. Most just said don’t disassemble any further...Well, I wanted to replace the spring so I needed your video. THANK YOU much!
100% useful video.
closing video but clear and understand i want?
intersting video
the channel admin not answer my question
not necessarily true. i did that myself and i got it out. it is a pain in the ass but i did it but you are right that part is the most tricky part