Use the orange/orange white for one balun and the green/green white for the other the twist rates on these cables are for transmitting data ( if using a cat 5 cable for an ip network the blue and orange pairs transmit data, the blue and brown power). If you look at the cable you should see the wires on the blue and orange pairs are twisted more than the other two. I always run an additional cable for the power for non poe devices ( 4 core or figure of 8). Make sure your cables aren't running parallel to power cables, if they are you need to have a gap of at least 100mm. If everything else fails install a ground loop isolator on affected Camaras.
good am sir pearson, you mean for otp cable orange/orange white for one balun means this two wire for one camera? and green/green white for onother balun of camera?
There is no problem using cats6 for for power & video, we do it all the time with no issues at all. A few things to remember is video baluns on both sides(camera side/dvr) & always use single pairs for video, otherwise you will get interference sometimes called "ghosting". So say you have 2cams next to each other use orange/orange-white for 12vdc positive, brown/brown-white for 12vdc negative, blue + on balun, blue-white - on balun for one cam & green + on balun, green-white - on balun for 2nd cam, you can use the same power for both cams if it's not long distances or run an extra power cable 2x0.75.
Pede yan gagana boss pag ganyan ang problema yung negative na connected sa videoballon then yung negative ng power..kukuha ka ng negative dun mismo sa power supply tapos series mo dun sa negative dun sa videoballon
Yung gamit nyo po bang cat6 ay cca po? Hanggang ilang metro kaya yung dc power? Yung kasama kasi sa package nmin is 12v8a adaptor kaso 8x5mp camera i kakabit doon.
boss ano kaya sira, bigla nawawala lahat ng video sa 11 camera na nakalagay, tapos tapos balik na naman lahat mga 7-10 seconds posible po kaya yung supply ang probz Specs Hikvision analog centralized power supply
sir nag install ako ng cctv sa apartment ko pure copper utp cat 6 ang ginamit ko at walang electrical wire naman kasama sa pvc bakit ne interference ang video? at 30 amps naman ang central power supply. try ko din today gumamit ng external adaptor every camera para malamat kung ang power supply ang nag produce ng interference baka pangit ang filtration ng dc power nya. palagay wala sa utp kase pure copper na sya.
Use the orange/orange white for one balun and the green/green white for the other the twist rates on these cables are for transmitting data ( if using a cat 5 cable for an ip network the blue and orange pairs transmit data, the blue and brown power). If you look at the cable you should see the wires on the blue and orange pairs are twisted more than the other two. I always run an additional cable for the power for non poe devices ( 4 core or figure of 8). Make sure your cables aren't running parallel to power cables, if they are you need to have a gap of at least 100mm. If everything else fails install a ground loop isolator on affected Camaras.
Thank you for your feedback
good am sir pearson, you mean for otp cable orange/orange white for one balun means this two wire for one camera? and green/green white for onother balun of camera?
There is no problem using cats6 for for power & video, we do it all the time with no issues at all. A few things to remember is video baluns on both sides(camera side/dvr) & always use single pairs for video, otherwise you will get interference sometimes called "ghosting". So say you have 2cams next to each other use orange/orange-white for 12vdc positive, brown/brown-white for 12vdc negative, blue + on balun, blue-white - on balun for one cam & green + on balun, green-white - on balun for 2nd cam, you can use the same power for both cams if it's not long distances or run an extra power cable 2x0.75.
Thank you
hello do you have any tutorial video for that
Pede yan gagana boss pag ganyan ang problema yung negative na connected sa videoballon then yung negative ng power..kukuha ka ng negative dun mismo sa power supply tapos series mo dun sa negative dun sa videoballon
Salamat sir
Galing Master Diskarte Lang talaga
Salamat masta, GODBLESS
video balun ang gagamitin sa kabilaan, basta utp ang gamit mo...ok ang wiring nyo..
Salamat sir
Yung gamit nyo po bang cat6 ay cca po? Hanggang ilang metro kaya yung dc power? Yung kasama kasi sa package nmin is 12v8a adaptor kaso 8x5mp camera i kakabit doon.
Oo sir cca lang..50 meters sir kaya yan.
Kapag may dugtong Yung Rg9 coaxial cable nagkakaroon Ng interference dahil ba sa dugtong?
Yes sir pero try mu lagyan individual na power supply kung may pagbabgi ba
boss ano kaya sira, bigla nawawala lahat ng video sa 11 camera na nakalagay, tapos tapos balik na naman lahat mga 7-10 seconds
posible po kaya yung supply ang probz
Specs
Hikvision analog
centralized power supply
O try mu sir lagyan nang ibang supply...check mu baka mat nag loose
My friend I tried those screw bnc connectors and they don’t work it gets to much interference. You have to used v balun a pair
Thanks sir
Video balun gamitin mo pag Utp cable hindi BNC connector. Bnc pag RG6
Salamat idol
Balun na yan idol both ends
Video balun both ends. Hindi lang sa camera
Balun should be there on both the ends.
Thank you for your feedback sir
sir nag install ako ng cctv sa apartment ko pure copper utp cat 6 ang ginamit ko at walang electrical wire naman kasama sa pvc bakit ne interference ang video? at 30 amps naman ang central power supply. try ko din today gumamit ng external adaptor every camera para malamat kung ang power supply ang nag produce ng interference baka pangit ang filtration ng dc power nya. palagay wala sa utp kase pure copper na sya.
Ok sir try mu taasan ang amperahe lagyan mu nang proper ground yung dvr or pudy narin try and error ka lagyan mu supply bawat camera
so pano ba?