L298n Dual H-Bridge Motor Driver : DC Motors : PWM : Stepper Motors : Eye-On-Stuff
HTML-код
- Опубликовано: 5 окт 2024
- L298n Dual H-Bridge Motor Driver : DC Motors : PWM : Stepper Motor : Eye-On-Stuff
Please consider donating to my channel so I can make more videos for you:
www.eyeonstuff....
All my videos are here: / @eye-on-stuff5248
www.eyeonstuff.com
Please Subscribe and Support my channel.
Thank You
#eyeonstuff #maker #arduino
Short, accurate, and to the point for most. Thank you!
I don't understand why it's so hard for people to make a tutorial like this. Thank you! :D
have you ever made one?
Thanks for the brief and accurate video!
Thanks for this, I didn't realise 5v was needed on power supply and 5v when driving DC motors from Arduino.
Good video on L 298.board. Without arduino. Simple to understand.
You said you need to remove the jumper in order to turn the 5V output to 5V in. Then you show how a yellow 5V input is connected to the 5V header, while the jumper is still on. ???
I learned I could make stepper motors go faster by ramping up to the max speed specified and then go quicker with the signals which made the stepper go quicker.
new subscriber thank you for sharing always watching your video
great video. learned so much about these little buggers. thank you
Well done, thank you so much sir.
Great ! Thank you !
Thank you sir this might help me solve my robot problems
heyy wassup, im also doing a arduino projecct. what was you rrobot about
thank you very much sir ❤
Enjoyed learning from you.
Just to be clear folks, the contol inputs only support up to 1.5V according to the DataSheet. 5V is too much.
Thank you my dude❤
Superb and Thank you
Good video, very well explained 👍
may I ask, what is the purpose of this PIC12F683 microcontroller in this circuit for?
Thanks
Hello , i made an arduino controlled car using this motor driver and im able to control speed without pwm , how ?? Please explain
what should the frequency be, for controlling the speed of the DC motor?
can i power 2 L298N motor drivers with one battery/powerplug(12volt) or should i use 2 separate?
Can I bridge 2 L298n Dual H-Bridge Motor Drivers together to use 4 DC Motors Seperately?
Yes, two of those will in fact drive four motors. Technically, you can have four motors run of a single driver, though each of the the two extra motors will have the same output as each of the other two, due to the phisical pins they are screwed into.
Can you provide the code link and a circuit diagram of clockwise and counter clowise motor
7:13 your welcome!!
Hello, If I need to drive a NEMA 17 stepper motor having a phase current about 1.8Amps, is this module can be connected to the stepper motor driver controller module 36820? If so how?
If you want to melt things or want to catch things on fire then please go ahead and use this with a stepper motor... Recommending that somebody uses for a stepper motor is a dangerous proposition because as you know it gets extremely hot with even the slightest of use of any separate motor. The manufacturer of this device should stop advertising that it can be used for a stepper motor although it can be used for separate motor it's very dangerous to do so and should not ever ever be used for a super motor.
You convinced me to use this, and drive the fan with a Arduino, hahaha😁
Stepper Motor = Seperate Motor = Super Motor 😅
@@red2fire2haha
Question, i’ve been searching for an answer to my inrush current problems with a couple projects. I’ve been trying to rebuild a couple old cordless vacs with some lion cells. But the issue I run into is the BMS I’m using for these cuts power because of the inrush. All cells are balanced and high drain. Of course research yielded PWM. But I would like to use a controller without a pot that is 100% on all the time. Could I use this Module and leave motor one jumper in place for the 100% duty cycle and overcome my inrush issues? Or will this provide the same issue?
Thanks!
hey boss. im wanting to build a tattoo machine using a strepper motor but i know nothing about programing them. would you be willing to help me? i can of course pay you.
This is epic! Me likey 🥰
Circuit