Didn't you need to know core characteristics? I mean , how did you know how many turns to need to on primary side . The other thing is ,I did not see any auxiliary winding or optocoupler, don't you have feedback loop?
Hi. If I want to make 24v. 20A SMPS do I need to modify only transformer windings or some other parts as well. How many turns of what no magnetic wire do i need if transformer modification is needed. Thanks
If the frequency is higher you will make more variation of the magnetic flux in one second, look at the Faraday’s law and the way power transformers are designed you will understand ;)
Better than others that I've searched for... btw what is the specification of choke (output inductor)? Core size, winding numbers and size of wire please?
The 15k resistor from pin no 2 of the IC whether it is ground or connect to the IC's pin no 3 ? In pcb layout it is on pin no 3 and in circuit diagram it is grounded.plz reply.
12v x 10A so its 120 watt supply .... and if im not mistaken most amplifiers work on low amperage i don't know what you want this for but you can look on your product chip how much amperage its pulling every product have its requirements im sure that you wanna run some texas instrutments amplifier which most work from 500mAh to 2A this one is not for amps and its not a game im not sure for your electronic skills on transformers even a small transformer can do alot when its not made right its not worth the time or your safety even the 120w is not that small current it will slowly convert your lectricity into bills better hook up some walmart thing 24v max 2A to a 50-100w amplifier depend on the chip req some can run even on 12v !!!
Hello, i want to design an SMPS with 5v USB input and dual output of 12v and 5V for Battery and Ardunio respectively. I would request you to suggest a PCB board or an IC. Thanks and Regards
sir how can i identify the size of the ferrite core of a smps transformer. i am planning to re use the existing transformer ferrite core to wind new one.
@@CarlosFilmagem2008 Isso explode ao ligar!IR2153 sem soft start na entrada explode ao ligar,não monte.Tanto que ele usou uma lampada em série,senão iria explodir alí mesmo.E outra,12v sem regulação pra que?Qualquer variação na entrada elevará a tensão para mais de 17 volts,ou menos de 10volts.
Sir will you sale one smps?if yes for how many rupees? Plz tell me I want just one smps but I am a mechanical engineering student so I want that ready made. Plz plz
if you have science exhibition and you don't know what to do then quit your job youtube is most for hobbyists you could do this only cause you want to do it not cause your knowledge is low and you go to exhibitions in science ....
Search were there is a short circuit in your primary part of your smps (emi filter, rectifier, capacitor ... well every part where there is hot tension)
@@raphaelcoti692 thanks man I figured out that the ic was fake so I got a new genuine one and completed the project Today but there few Problems like unstable voltage maybe because I used bridge rectifier 35a at output?
@@anmolkumar6704 if it is unstable the probleme can provide from : - feedback system - output filter Or an omission of a part of the system Like forgot to put a « clamp » ...
@@raphaelcoti692 it's the same circuit as in the video but the output part is a bit different. I only have 1 mbr20100 dual diode (Rated for 10a each leg) and 2 other dual diode (rated for 5a each leg) which I don't know how to connect together in such a configuration to handle about 20a . I saw another schematic that was same but instead it used a full bridge rectifier at output. I winded my transformer 40v 16a in EE 42 core. The problem can be the slow rectification of the full bridge rectifier I used but I am not sure. Can u suggest a way to put the three double diodes for 20a??
Please download all file ( PCB file, lay file, PDF file, Gerber file ) here: drive.google.com/file/d/1UjW-VHvbHSNWNfw00ue3HTzWt3pBR8py/view Hope you get good power supply. Thanks
I really like a beautiful project. Possible to have the circuit diagram of the circuit? The IC is not written in the PDF file. in contrast DIP-8. I await the scheme if possible. Thank you so much .
Long Technical Ok, I'm waiting tomorrow for everything. I wanted to ask you if you could make a step-down dc-dc converter from 60vdc to 13.8vdc with SMPS mode is a current of 30 A. By chance could you help me in this project? . Thank you very much for your attention 😉
Sorry for the late reply. This is design of SMPS. I use IC IR2153 with R=15k and C= 1n it run at 47kHZ. Schematic below drive.google.com/file/d/1DSGv6t_E1NIaPafM3SMBRHerA2clo-yI/view?usp=sharing
Long Technical excellent you have been very kind and professional. I wanted to ask you what happens if I use 0.5mm wire for winding? Then I wanted to ask if you had any idea for a step-down SMPS dc-dc variable. Thank you very much for the attention.
Didn't you need to know core characteristics? I mean , how did you know how many turns to need to on primary side . The other thing is ,I did not see any auxiliary winding or optocoupler, don't you have feedback loop?
Why do you isolate the transistors from the radiator?
Which type or type is suitable for the IC?
Hi. If I want to make 24v. 20A SMPS do I need to modify only transformer windings or some other parts as well. How many turns of what no magnetic wire do i need if transformer modification is needed. Thanks
These people do for themselves to get views and likes only.
Hi
Thanks your good videos
How can reach this pcb schematic?
I remember i shared in description of this video, please check
very good. But you can use Acetone or Nail polish remover to wipe off the toner from the pcb instead. this will not thin out the copper traces.
Thanks you
APURBA DAS a elegir
How did you calculate the turns of transformer, What if i use different size or shape transformer any good source to know about its calculation ?
Check the software for calculate the turns of transformer when use ir2153 on google. I don"t remember the name of software
Can you make a list of what you used in this circuit?
Ah, inductor soup! Reminds me of my childhood! Special occasions. We always had inductor soup!!
Inductor soup !!!! LOL
Is there an explanation for as increasing frequency would give more power for a switching mode power supply ?
If the frequency is higher you will make more variation of the magnetic flux in one second, look at the Faraday’s law and the way power transformers are designed you will understand ;)
@@raphaelcoti692
Thank you for your answer.
How can I measure board size in Sprint Layout 6.0
The definition of hand made.
Resistor value in transistor gate ??? 27 ohm or 27 kohm
27r
@@LongTechnical 27 ohm or 27 k ohm
How can I add LED to show if it is connected to load..The LED show come on whenever it sense load connected.
I know I'm little late, but, please, can you tell me what kind of glue did you use for this transformer (to glue the core)?
aparently it's super glue, it's not that impotant
Good work. Thanks. But where is feedback? Where is optocoupler?
Better than others that I've searched for... btw what is the specification of choke (output inductor)? Core size, winding numbers and size of wire please?
which ic used in it ?
IR2153 bro
Please share smps transformer design calculations
without feedback opto ?
Pcb see extra coper print hatane ke liye Kon sa acid use Kiya please batao
@2:27 rats?
funciona para 110v ??? works for 110v???
The 15k resistor from pin no 2 of the IC whether it is ground or connect to the IC's pin no 3 ? In pcb layout it is on pin no 3 and in circuit diagram it is grounded.plz reply.
15k resistor from pin no 2 connect to pin no 3
has commercial for JCpcb then literally makes his own pcb hahaha
can it be used for amps?
and what is the maximum wattage amp
12v x 10A so its 120 watt supply .... and if im not mistaken most amplifiers work on low amperage i don't know what you want this for but you can look on your product chip how much amperage its pulling every product have its requirements im sure that you wanna run some texas instrutments amplifier which most work from 500mAh to 2A this one is not for amps and its not a game im not sure for your electronic skills on transformers even a small transformer can do alot when its not made right its not worth the time or your safety even the 120w is not that small current it will slowly convert your lectricity into bills better hook up some walmart thing 24v max 2A to a 50-100w amplifier depend on the chip req some can run even on 12v !!!
Hi
What is the inductor capacity of this circuit?
Thanks😍😍😍
hello sir
i got psu atx 12v 16a
how to reduce the max current to 10a pleasee
please give the simple way
pwm tl494
Con ic tạo dao động là gì vậy anh
Ir2153
I don't see voltage feedback in your design. Does it have short circuit protection ?
No feeback. Only fuse for short circuit protection
i want to make that but im confuse in secondary winding.
Hello I need the picture of the circuit diagram
IC details not mentioned which IC is that
Hello, i want to design an SMPS with 5v USB input and dual output of 12v and 5V for Battery and Ardunio respectively. I would request you to suggest a PCB board or an IC.
Thanks and Regards
Just buy boot converter about 1 usd
@@LongTechnical γονημουκα
Could you make 32v 5A from part of atx psu?
why are you scrubbing it?
sir how can i identify the size of the ferrite core of a smps transformer. i am planning to re use the existing transformer ferrite core to wind new one.
Try with any core
Why every project is limited to 10 15A
a cho e hỏi nếu e muốn chỉnh thành 5v 30a thì thay đổi ntn ạ
Thì quấn lai biến áp e
IC ke pin no 2 se jo 15k hai wo ground hai ya pin no 3 ko gaya hai.Diagram mai ground hai aur aapne pin 3 mai diya hai.plz reply.
English please, !
component list?
Sir u provide pcb and componant layout pdf
whats driver ic model?
The music makes me cry.
Sorry for that ☺
We can't see the readings in your multimeter.
how do you adjust the voltage output?
Put a potentiometer/variable resistor on the output side. Similar to volume knobs.
Nice build!
Thank
Half through the video and subbed
Bro I want this 12 v 10 a smps ic number if video.
sir i didnt find that ic detail in doc what ic it is please tell me
Ir2153
master ? if it to changing or modif to be 12vdc 60 a. how to changing ?
O DIAGRAMA, ONDE ESTAR ? SÓ ESTAR DISPONIVEL O DESENHO DA PLACA DE CIRCUITO IMPRESSO. VOCÊ PODERIA DISPONIBILIZAR O DIAGRAMA ?
ta na descrição
@@CarlosFilmagem2008 Isso explode ao ligar!IR2153 sem soft start na entrada explode ao ligar,não monte.Tanto que ele usou uma lampada em série,senão iria explodir alí mesmo.E outra,12v sem regulação pra que?Qualquer variação na entrada elevará a tensão para mais de 17 volts,ou menos de 10volts.
sir what modification to be done for output short circuit protection
In the next time
hi thanks for the vedeo can you give me the name of the ic that you have used
IR2153
I learned a lot .. thanks!!! 110V mains overthere?
220V
Sir will you sale one smps?if yes for how many rupees? Plz tell me I want just one smps but I am a mechanical engineering student so I want that ready made. Plz plz
how to do the transformer calculations ?
I use IC IR2153 with R=15k and C= 1n it run at 47kHZ. schematic bewlow
drive.google.com/file/d/1DSGv6t_E1NIaPafM3SMBRHerA2clo-yI/view?usp=sharing
thanks for the link , can you make a video about simple short circuit protection circuit ?
Good job man but lot of wasting water don't ignore
Which paper is used for printing???
calendar paper
Long ơi sao mình download về điện thoại sao ko được vậy ta
I thought you were gonna make an smps transformer....not an smps circuit dawg..
Your trans and emi is very big for 120w smps
IC type please sir....
not list in pdf file
thanks
Ir2153 bro
@@LongTechnical thank's...👍
Thank you . Wonderful Circuit
What are you makeing
PSU
bro please help . with in 14 days iam having national science exhibition .I need 40v 10+ amp smps . iam having. a atx
if you have science exhibition and you don't know what to do then quit your job youtube is most for hobbyists you could do this only cause you want to do it not cause your knowledge is low and you go to exhibitions in science ....
The SMPS just failed with no output and the ac bulb is glowing
What should I do
Search were there is a short circuit in your primary part of your smps (emi filter, rectifier, capacitor ... well every part where there is hot tension)
@@raphaelcoti692 thanks man
I figured out that the ic was fake so I got a new genuine one and completed the project Today but there few Problems like unstable voltage maybe because I used bridge rectifier 35a at output?
@@anmolkumar6704 if it is unstable the probleme can provide from :
- feedback system
- output filter
Or an omission of a part of the system
Like forgot to put a « clamp » ...
Maybe i should see your scematic of your smps to help you a better way
@@raphaelcoti692 it's the same circuit as in the video but the output part is a bit different.
I only have 1 mbr20100 dual diode
(Rated for 10a each leg) and 2 other dual diode (rated for 5a each leg) which I don't know how to connect together in such a configuration to handle about 20a .
I saw another schematic that was same but instead it used a full bridge rectifier at output.
I winded my transformer 40v 16a in EE 42 core.
The problem can be the slow rectification of the full bridge rectifier I used but I am not sure.
Can u suggest a way to put the three double diodes for 20a??
Excellent project
thank you
Please download all file ( PCB file, lay file, PDF file, Gerber file ) here: drive.google.com/file/d/1UjW-VHvbHSNWNfw00ue3HTzWt3pBR8py/view
Hope you get good power supply. Thanks
circuit diagram please
Awesome bro very well!!!!1
keep it up and nice work
Circuit diagram please
220v to 12 or 110 to 12
Circuit diagram?
I really like a beautiful project. Possible to have the circuit diagram of the circuit? The IC is not written in the PDF file. in contrast DIP-8. I await the scheme if possible. Thank you so much .
I will upload tomorrrow. Thank for watch my video
Long Technical Ok, I'm waiting tomorrow for everything. I wanted to ask you if you could make a step-down dc-dc converter from 60vdc to 13.8vdc with SMPS mode is a current of 30 A. By chance could you help me in this project? . Thank you very much for your attention 😉
Sorry for the late reply. This is design of SMPS. I use IC IR2153 with R=15k and C= 1n it run at 47kHZ. Schematic below
drive.google.com/file/d/1DSGv6t_E1NIaPafM3SMBRHerA2clo-yI/view?usp=sharing
Long Technical excellent you have been very kind and professional. I wanted to ask you what happens if I use 0.5mm wire for winding? Then I wanted to ask if you had any idea for a step-down SMPS dc-dc variable. Thank you very much for the attention.
0.5mm good for winding. For your project i think you can use iC SG3525
Circuit please
Bad project.IR2153 without soft start blowup at start.And 12v without regulation no way.
blow up. LOL
please modify psu 12v 35A or 40A for amplifiers
ok next time
for a minimum of 300 watts
thanks master 🙏🙏
please explain what the name is menit 4.24 and how to make it
AC Line filter Common Mode Choke. Take from old power supply
I got a pull from a used TV, but the shape is rather small than that, is it the same?
And how can I contact you?
Sir ic name
cho em xin link kênh tiếng việt của anh ạ
Please give me brother your Gerber files
5:19 Mom yelling: HOW MANY TIMES DO I HAVE TO TELL YOU NOT TO USE THE COOKWARE FOR YOUR SCIENCE PROJECTS!!!
V.v..v.v nice brother..
Very nice job
Why all are using yello tape?
sir je yeh Fec13 kaha milega
FECL3
You not 8pin IC number.....this is very important switching IC.......
smps 12v to 60A or more please
DRIVER IC KA NO. NAHIN HAI
Nice build.
Thanks
Nice... 👍👍👍
ทำใด้ด้วยหรอคับเก่งจิงๆ
Circuit diagram
Ic model please
Ir2153
@@LongTechnical thanks big like
Please build 12v 30A smps.
Very Nice!
No file,
i m like layout black.white paper
Save water